Skip to content
Residential pool with faint brownish stains on a white plaster floor near the shallow end
Pool care: water chemistry

Pool Stains: How to Identify, Remove and Prevent Them by Color

Pool stains are organic or metal: hold chlorine on the spot, then vitamin C. If vitamin C lifts it, treat the water with ascorbic acid at 1 lb per 10,000 gallons and follow with a sequestrant.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓Two tablets sort most stainsChlorine lightens organic stains; vitamin C lightens metal stains within 2 minutes (Natural Chemistry).
  • ✓Label doses, not guesses1 lb ascorbic acid per 10,000 gallons, then 1 L of METALfree per 20,000 gallons and no shock for 1 week.
  • ✓Iron stains at 0.3 mg/LEPA lists reddish staining above 0.3 mg/L iron, black above 0.05 mg/L manganese, blue-green above 1.0 mg/L copper.
Quick answer
Most pool stains are organic (green or brown, from leaves) or metal (rust brown from iron, blue-green from copper, black from manganese). Chlorine lightens organic stains; vitamin C lightens metal ones within 2 minutes. For metal, drop chlorine to 1 ppm, add ascorbic acid at 1 lb per 10,000 gallons, then a sequestrant.
Vitamin C, 2 minutes
Stain test
1 lb per 10,000 gal
Ascorbic acid dose
0.3 mg/L
Iron staining level
Source: EPA (2026)
1 week
No shock after

Key takeaways

  • A vitamin C tablet held on a stain for at least 2 minutes separates metal (it lightens) from non-living organic (no change), per Natural Chemistry, a pool chemical maker.
  • Natural Chemistry’s metal stain procedure lowers chlorine to 1 ppm, keeps pH at 7.2 to 7.6, doses 1 lb of ascorbic acid per 10,000 gallons and bans shock for at least 1 week (Natural Chemistry procedure).
  • EPA lists reddish or orange staining above 0.3 mg/L iron, black staining above 0.05 mg/L manganese and blue-green staining above 1.0 mg/L copper (EPA secondary standards, updated May 2026).
  • The 2024 Model Aquatic Health Code Annex names the usual metal sources: copper from algaecides or corroded pipes, and iron and manganese from fill water (2024 MAHC Annex).
  • Latham’s 2026 fiberglass warranty does not cover staining and is voided if water drops below the skimmer outlet, so fiberglass stains are treated in the water, not by draining (Latham warranty).

What do pool stain colors mean?

Color gives a suspect, and a 2 minute test confirms it. Green or brown under leaves is organic. Yellow, brown or reddish brown is generally iron, blue-green is copper, and gray or black is oxidized copper, per Pinch A Penny’s 2022 guide. River Pools adds manganese for brown, black or purple hues, and EPA ties black staining to manganese above 0.05 mg/L.

Pool stains by color and location: likely cause, field test result and first fix, with the source for each row
Stain color and where it showsMost likely causeField test resultFirst fixSource
Green or brown flat patch under leaves, acorns or wormsNon-living organic (tannin)Chlorine lightens it; vitamin C does notRaise chlorine to breakpoint and scrubNatural Chemistry; Pinch A Penny
Green film or fuzz that brushes off and returnsGreen algaeNot a stain: it is alive and spreadsShock and filter (green pool steps)Natural Chemistry; BioGuard
Yellow-brown powder on shady walls that brushes off easilyMustard algaeReturns within days after brushingMustard algae treatmentBioGuard; Algae Complete label 5185-513
Raised, rough blue-black spots on plasterBlack algae (cyanobacteria)Vitamin C does not change it; nylon brush barely moves itStainless steel brush on plaster, then a labeled productNatural Chemistry; Pentair; EPA labels
Yellow, brown, orange or reddish-brown, often near steps, fittings or the floorIronVitamin C lightens itAscorbic acid, then a sequestrantPinch A Penny; River Pools; EPA (iron: reddish or orange staining)
Blue, blue-green or tealCopperVitamin C or a citric acid product lightens itCitric or ascorbic acid stain remover, then a sequestrantPinch A Penny; River Pools; EPA (copper: blue-green staining)
Gray or black flat stainOxidized copper or manganeseA non-chlorine shock spot test turns copper yellow or reddishStain ID kit first, then the matching treatmentPinch A Penny (gray or black: oxidized copper); EPA (manganese: black staining)
Brown, black or purple huesManganeseVitamin C lightens it if it is metalAscorbic acid, then a sequestrantRiver Pools; EPA
White, crusty, rough to the touchCalcium scale, not a stainA drop of muriatic acid makes carbonate foamScale method by tile or finish typeLatham (via our tile cleaning guide); Pinch A Penny
Dark spots in fiberglass that ignore every treatmentCobalt staining beneath the gelcoatNo reaction to brushing, vitamin C or ascorbic acidHave a fiberglass pro evaluate itRiver Pools (fiberglass maker)

Sources: Natural Chemistry; Pinch A Penny stain guide (June 6, 2022); River Pools (updated April 9, 2026); BioGuard; EPA secondary standards. Download CSV

A rust-brown stain on white plaster steps is the classic iron suspect. Iron stains above 0.3 mg/L per EPA, and steps are where Natural Chemistry points its milder STAINfree product.
A rust-brown stain on white plaster steps is the classic iron suspect. Iron stains above 0.3 mg/L per EPA, and steps are where Natural Chemistry points its milder STAINfree product.

Two colors mislead often. A raised, rough blue-black spot on plaster is usually black algae, which our black algae in pool guide separates from metal with the same vitamin C test. A dark fiberglass spot that ignores every product can be cobalt staining beneath the gelcoat, which River Pools, a fiberglass pool maker, says brushing, vitamin C and ascorbic acid treatments will not remove. Both fail the 2 minute vitamin C test.

Pool stains: the key numbers and where each comes from
NumberWhat it isSource and date
2 minutesMinimum time a vitamin C tablet sits on a stain before you read the resultNatural Chemistry staining guide
1 lb per 10,000 galAscorbic acid (STAINfree Extra Strength) dose for surface metal stainsNatural Chemistry metal stain removal procedure
1 ppmChlorine level to lower to before an ascorbic acid treatmentNatural Chemistry procedure
1 L per 20,000 galMETALfree sequestrant dose added after the stain liftsNatural Chemistry procedure
1 weekMinimum wait before shocking after a metal stain treatmentNatural Chemistry procedure; Jack's Magic FAQ
65FWater temperature the pool must exceed before a stain treatment programPinch A Penny stain guide, June 2022
0.3 mg/LIron level above which EPA lists reddish or orange stainingEPA secondary standards, page updated May 2026
1.0 mg/LCopper level above which EPA lists blue-green stainingEPA secondary standards, page updated May 2026
0.05 mg/LManganese level above which EPA lists black stainingEPA secondary standards, page updated May 2026
28 daysWindow in which new plaster is most susceptible to stainingNational Plasterers Council start-up card, rev. 03-2021

Sources: Natural Chemistry; Natural Chemistry procedure; Jack’s Magic FAQ; Pinch A Penny; EPA; NPC start-up card. Download CSV

How do you test a pool stain before treating it?

Run two spot tests in order. Pinch A Penny says chlorine placed over an organic stain usually removes it. If chlorine does nothing, hold a vitamin C tablet on the stain for at least 2 minutes: Natural Chemistry reads lightening as metal. If neither works, a stain ID kit tests several acid products, and a water test for iron and copper comes next.

  1. Balance firstPinch A Penny wants water above 65F, free chlorine 3.0 ppm or below and pH 7.4 or below before any stain test.
  2. Turn the pump offLet the water stand 30 minutes so the test product stays on the spot (Pinch A Penny).
  3. Chlorine on the spotHold chlorine over a small stain on plaster. On vinyl, skip the tablet: EPA label 5185-441 warns against undissolved granules resting on a liner.
  4. Vitamin C on the spotIf chlorine did nothing, hold a vitamin C tablet on the stain for at least 2 minutes (Natural Chemistry). Lighter means metal.
  5. Test the waterTest iron and copper. Jack’s Magic says a stain can exist at 0 ppm, and any reading above 0 should be sequestered first.
Two-tablet test: the four result combinations and what to do next
Chlorine on the spotVitamin C on the spotWhat it meansNext stepSource
LightensNo changeOrganic stain (leaves, debris, algae residue)Breakpoint chlorine and scrubbing; skim debris dailyPinch A Penny; Natural Chemistry
No changeLightens in 2 minutes or lessMetal stain, usually iron or copperAscorbic acid treatment, then a sequestrant; no shock for 1 weekNatural Chemistry procedure
No changeNo changeScale, cobalt, a deep or mixed stain, or a reagent problemStain ID kit with several acid products; check scale with a muriatic acid dropPinch A Penny; Jack's Magic FAQ; River Pools
No changeDarkens or changes colorPossible copper or mixed metals; Pinch A Penny's non-chlorine shock spot test turns copper yellow or reddishStop; test the water for copper and iron, then use a stain ID kitPinch A Penny; Jack's Magic FAQ

Sources: Pinch A Penny; Natural Chemistry; Jack’s Magic FAQ; River Pools. Download CSV

Pool stain flowchart: chlorine test, vitamin C test, water test, then treatment. The two-tablet table above holds the same logic as text.
Pool stain flowchart: chlorine test, vitamin C test, water test, then treatment. The two-tablet table above holds the same logic as text.

Where do metal stains in a pool come from?

Mostly from four places: fill water, corroded equipment, copper algaecides and copper ionizers. The 2024 MAHC Annex names copper from algaecides or corroded pipes and iron and manganese from fill water. BioGuard adds corroded heater parts and says a pH rise or a shock dose is what drops dissolved metals onto the surface.

Where pool metals come from, how they get in and what to check
Where the metal comes fromHow it gets into the waterWhat to checkSource
Fill water, especially well waterIron and manganese arrive dissolved in source waterTest fill water for metals before filling (NPC); iron above 0.3 mg/L and manganese above 0.05 mg/L stain fixtures (EPA)MAHC Annex; Natural Chemistry; NPC; EPA
Corroded heater parts, pipes and metal fittingsLow pH, low alkalinity or low calcium make aggressive water that dissolves metal partsKeep pH 7.2 to 7.6 during treatment and 7.0 to 7.8 at home pools; bypass the heater during stain treatments where possibleBioGuard; MAHC Annex; Natural Chemistry; CDC; Jack's Magic
Copper algaecidesEach label dose adds copper; 4 oz of Swimtrine adds about 0.27 ppm per 10,000 galLeslie's says staining may occur above 0.6 ppm copperMAHC Annex; EPA label 8959-2; Leslie's
Copper ionizersIon systems hold copper in the water on purposeMAHC Annex cites a 1.3 ppm copper standard and warns against adding copper algaecidesMAHC Annex; Jack's Magic
A pH rise or a shock doseDissolved metals turn insoluble and drop onto the surfaceTest metals before shocking; this is when stains appearBioGuard
FloodwaterHurricane or canal flooding leaves orange-brown stains from mixed organics and inorganicsDrain and replace the water, then use a stain ID kitJack's Magic FAQ

Sources: 2024 MAHC Annex; BioGuard; Natural Chemistry; NPC; EPA; EPA label 8959-2; Leslie’s; Jack’s Magic; CDC. Download CSV

Copper algaecide is the source owners add themselves. A 4 oz opening dose of Swimtrine adds about 0.27 ppm of copper per 10,000 gallons, and Leslie’s warns that staining may start above 0.6 ppm, as our pool algaecide guide charts dose by dose. Ion systems hold copper on purpose: the MAHC Annex cites a 1.3 ppm copper standard for them, and our pool ionizer guide covers how they are dosed.

Metal levels linked to staining, by source
Metal and limitLevel (ppm or mg/L)What the source says happens above itSource
Manganese, EPA secondary standard0.05Black to brown color; black stainingEPA secondary standards (updated May 26, 2026)
Iron, EPA secondary standard0.3Rusty color; reddish or orange stainingEPA secondary standards (updated May 26, 2026)
Copper, staining caution before a copper algaecide0.6Staining may occurLeslie's black algae guide
Copper, EPA secondary standard1.0Metallic taste; blue-green stainingEPA secondary standards (updated May 26, 2026)
Copper, ion system standard cited in the MAHC Annex1.3Operating outside the maker's range can cause staining2024 MAHC Annex 5.7.3.2.3

Sources: EPA Secondary Drinking Water Standards (updated May 26, 2026); Leslie’s; 2024 MAHC Annex 5.7.3.2.3. Download CSV

Metal levels linked to pool and fixture staining, by source (US, 2024 to 2026)ppm (mg/L); EPA figures are drinking water aesthetic standards, not pool rules
Metal levels linked to pool and fixture staining, by source (US, 2024 to 2026)Bar chart: manganese stains black above 0.05 ppm, iron reddish above 0.3, copper may stain above 0.6 per Leslie's, EPA lists blue-green staining above 1.0 and the MAHC cites 1.3 for ion systems.Manganese, EPA (black staining): 0.05Manganese, EPA (black staining)0.05Iron, EPA (reddish or orange staining): 0.3Iron, EPA (reddish or orange staining)0.3Copper, Leslie's caution: 0.6Copper, Leslie's caution0.6Copper, EPA (blue-green staining): 1Copper, EPA (blue-green staining)1Copper, MAHC ion systems: 1.3Copper, MAHC ion systems1.3

Manganese and iron stain at far lower levels than copper, which is why a fill water test matters more than the copper reading alone.

Source: EPA Secondary Drinking Water Standards (updated May 26, 2026); Leslie's black algae guide; 2024 MAHC Annex 5.7.3.2.3. Download chart data (CSV)

Floodwater is the odd case. Jack’s Magic, a stain treatment maker, says hurricane or canal flooding leaves orange-brown stains and floodwater up to 10 times saltier than a salt pool, so the water has to be drained and replaced before any stain test. Our pool hurricane rules research shows official Florida guidance agrees on keeping water in the pool before a storm, which protects the shell.

How do you remove metal pool stains without draining?

Treat the water, not the shell. Natural Chemistry’s procedure balances pH to 7.2 to 7.6, lowers chlorine to 1 ppm, adds 1 lb of ascorbic acid per 10,000 gallons near the stains with the pump off overnight, then adds METALfree at 1 L per 20,000 gallons and skips shock for at least 1 week. River Pools gives the same 1 lb rate.

  1. Balance and lower chlorinepH 7.2 to 7.6 (7.2 works best), alkalinity 80 to 120 ppm, calcium 200 to 400 ppm, phosphates under 100 ppb, chlorine 1 ppm.
  2. Pick the productSTAINfree (citric acid) for minor stains on small areas or steps; STAINfree Extra Strength (ascorbic acid) for older stains on floors and walls.
  3. Dose near the stain1 lb per 10,000 gallons as close to the stains as possible, pump off overnight. For discolored water, broadcast it and circulate 1 hour.
  4. Brush and vacuumUse bristles that suit the surface, vacuum walls and floor, then let it sit overnight.
  5. Lock up the metalPump on, add METALfree at 1 L per 20,000 gallons around the perimeter, then add pulp filter aid.
  6. Clean the filterSand: backwash at least 3 minutes and rinse 2 minutes. Cartridge: clean the cartridge and tank.
  7. Rebalance slowly, no shockBack to normal pH and alkalinity; no shock for at least 1 week; then 4 oz of METALfree per 10,000 gallons weekly.
Natural Chemistry metal stain removal procedure (read November 2, 2026): the chlorine target, the 1 lb per 10,000 gallon dose, the METALfree rate and the one week shock ban, boxed in red.
Natural Chemistry metal stain removal procedure (read November 2, 2026): the chlorine target, the 1 lb per 10,000 gallon dose, the METALfree rate and the one week shock ban, boxed in red.

How much vitamin C for pool stains? Dose by pool size

One pound of ascorbic acid per 10,000 gallons is the label rate from Natural Chemistry and the rate River Pools gives for fiberglass, so a 20,000 gallon pool takes 2 lb and a 30,000 gallon pool 3 lb. The sequestrant follows at 1 L per 20,000 gallons. Measure your volume first; a 25% error in gallons is a 25% error in dose.

Worked arithmetic: ascorbic acid and sequestrant doses for six pool sizes at the label rates
Pool volume (gallons)Ascorbic acid, STAINfree Extra Strength (lb)METALfree start dose (liters)METALfree start dose (fl oz)Weekly METALfree after treatment (fl oz)Jack's Magic Blue or Purple Stuff start dose (quarts)
10,00010.516.941
15,0001.50.7525.461.5
20,0002133.882
25,0002.51.2542.3102.5
30,00031.550.7123
40,0004267.6164

Sources: Natural Chemistry procedure (1 lb per 10,000 gal; 1 L per 20,000 gal; 4 oz per 10,000 gal weekly); Jack’s Magic FAQ (1 qt per 10,000 gal); NIST (1 fl oz = 29.57 mL). PC&S arithmetic. Download CSV

Ascorbic acid for metal pool stains, pounds by pool size (label rate, 2026)STAINfree Extra Strength at 1 lb per 10,000 gallons
Ascorbic acid for metal pool stains, pounds by pool size (label rate, 2026)Bar chart: 1 lb of ascorbic acid for 10,000 gallons rising to 1.5, 2, 2.5, 3 and 4 lb for 15,000 to 40,000 gallons.0123410,000 gal: 110,000 gal15,000 gal: 1.515,000 gal20,000 gal: 220,000 gal25,000 gal: 2.525,000 gal30,000 gal: 330,000 gal40,000 gal: 440,000 gal

River Pools gives the same 1 lb per 10,000 gallons for fiberglass pools.

Source: Natural Chemistry metal stain removal procedure (read November 2, 2026); PC&S arithmetic for each pool size. Download chart data (CSV)

Gallons drive every number in that table, so measure before dosing: a pool you think holds 20,000 gallons but really holds 25,000 gets 2 lb where the label calls for 2.5 lb. Ascorbic acid also uses up chlorine and pulls pH down, which is why Natural Chemistry’s step 9 rebalances to pH 7.2 to 7.6 and alkalinity 80 to 120 ppm before chlorine goes back up.

Four maker and retailer procedures for metal stains, compared step by step
StepNatural Chemistry (STAINfree procedure)River Pools (fiberglass maker blog, Apr 2026)Pinch A Penny (Suncoast program, Jun 2022)Jack's Magic (FAQ)
Chlorine before treatingLower to 1 ppmLower to 0.0 ppm3.0 ppm or belowLow; raise gradually after a #1 treatment
pH before treating7.2 to 7.6, low end preferredAbout 7.27.4 or belowBalanced
Other targetsAlkalinity 80 to 120 ppm, calcium 200 to 400 ppm, phosphates under 100 ppbNot statedAlkalinity 80 ppm or below, calcium 400 ppm or below, CYA 70 ppm or below, water above 65FWater above 65F; test iron and copper first
Stain remover dose1 lb per 10,000 gal near the stain, pump off overnightAbout 1 lb ascorbic acid per 10,000 gal, run 24 hoursSpot test with a stain ID kit, then a store procedure (A to D)Stain ID kit decides the product
SequestrantMETALfree 1 L per 20,000 gal, then 4 oz per 10,000 gal weeklyAdd a metal sequestering agentUse a metal control product periodicallyBlue or Purple Stuff, 1 qt per 10,000 gal start dose
Shock afterNot for at least 1 weekNot statedNot statedNot for at least 1 week

Sources: Natural Chemistry; River Pools (April 9, 2026); Pinch A Penny (June 6, 2022); Jack’s Magic FAQ. Download CSV

The four procedures agree on the order: low chlorine, low pH, stain remover, sequestrant, no shock. They disagree on the chlorine floor, from 0.0 ppm at River Pools to 1 ppm at Natural Chemistry and 3.0 ppm or below at Pinch A Penny. Follow the label of the product you bought, since its dose was set for its own chlorine target.

How do you remove algae and organic stains from pool walls?

With chlorine and a brush. Natural Chemistry raises chlorine to breakpoint, scrubs the stain, then expects chlorine back below 5 ppm within 24 hours before an enzyme dose. Live algae is a separate job: green water, mustard powder and black spots each have their own treatment. On fiberglass, River Pools says many organic stains fade within a few weeks to a couple of months. Our pool algae guide routes each type to its treatment with a flowchart.

Leaves, acorns and worms release tannins that leave green or brown marks, and Natural Chemistry notes they often look like algae, and vitamin C leaves them unchanged after 2 minutes. The difference is that an organic stain is flat and does not regrow. If the spot is fuzzy, slimy or spreading, start with how to clear a green pool; a yellow powder that brushes off and returns in the shade is covered in our mustard algae guide. Why earthworms end up in the pool after rain, and how to keep them out, is covered in worms in pool water.

Wet leaves resting on a light plaster floor: the source of the flat brown tannin stains that chlorine lightens. Natural Chemistry lists leaves, worms and acorns as the usual causes.
Wet leaves resting on a light plaster floor: the source of the flat brown tannin stains that chlorine lightens. Natural Chemistry lists leaves, worms and acorns as the usual causes.

Brown stains on pool steps can be either kind, so test before treating. Steps hold leaves in still water, and they are also where Natural Chemistry points its milder citric acid STAINfree for small metal stains. If chlorine lightens the step stain, it was organic; if vitamin C does within 2 minutes, it was metal.

How do you remove stains from a fiberglass pool or vinyl liner?

In the water, gently, and without draining. River Pools treats fiberglass metal stains with chlorine at 0.0 ppm, pH near 7.2 and about 1 lb of ascorbic acid per 10,000 gallons for 24 hours. Latham’s 2026 warranty is voided if water drops below the skimmer outlet, and GLI’s liner warranty is void against shrinkage if the pool is emptied.

Stain rules by pool surface: safe methods, what to avoid and the warranty or maker rule behind each
SurfaceSafe stain methodsAvoidWarranty or maker ruleSource
Plaster or other cement finishTwo-tablet test; ascorbic acid and sequestrant; breakpoint chlorine with a brush; stainless brush for black algaeAcid washing new plaster; LSI above plus 0.3NPC: first 28 days most stain-prone; LSI 0.0 to plus 0.3; positive LSI causes metal stainingNPC start-up card (rev. 03-2021)
Pebble or quartz aggregateIn-water treatments as for plaster; nylon brushTraditional acid wash (loosens aggregate); PoolDial suggests a 10:1 rinse at mostFollow the finish maker's start-up and care guidePoolDial acid wash guide; Leslie's (nylon on pebble)
Fiberglass gelcoatSoft sponge, fiberglass-safe eraser, ascorbic acid at about 1 lb per 10,000 gal, sequestrantAbrasive or wire brushes, steel wool, harsh chemicals, draining below the skimmerLatham's 2026 warranty excludes staining and is voided if water drops below the skimmer outletRiver Pools; Thursday Pools; Latham warranty
Vinyl linerAscorbic acid and sequestrant in the water; nylon brushResting chlorine tablets or undissolved granules on the liner; acid wash; emptying the poolGLI liner warranty covers seam separation, excludes improper chemical use and fading, and is void against shrinkage if the pool is emptiedGLI warranty card; EPA label 5185-441; Pinch A Penny

Sources: NPC start-up card (rev. 03-2021); PoolDial; Leslie’s; River Pools; Thursday Pools; Latham 2026 fiberglass warranty; GLI liner warranty card; EPA label 5185-441; Pinch A Penny. Download CSV

Read the warranty before treating, because neither maker promises the color. Latham’s fiberglass warranty excludes fading, staining and discoloration of the surface finish (section 8j), and GLI’s liner card covers seam separation, not stains, and excludes improper chemical use. What both protect is the structure, which is why draining for an acid wash is off the table on both surfaces; our how to drain a pool guide covers the rules. Pink or purple blotches inside a vinyl liner are a different case, a bacterial pigment that chlorine only bleaches for a while, as our guide to pink algae in pool water explains.

Which pool stain fix fits your pool? Decision table

Match the test result and the surface to one action. Organic stains get breakpoint chlorine. Metal stains get ascorbic acid at 1 lb per 10,000 gallons and a sequestrant, after metals in the water are sequestered to 0.00 ppm. Fiberglass spots that ignore everything may be cobalt. A stain that survives two full treatments on old plaster is an acid wash or resurfacing question.

If your situation is X, do Y: pool stain decision table with the rule behind each row
If your situation isDo thisRule behind it (source)
Green or brown flat stain under leaves, and chlorine lightens itRaise chlorine to breakpoint, scrub, and let chlorine fall below 5 ppm within 24 hoursNatural Chemistry organic stain method
Brown, rust or blue-green stain that vitamin C lightensLower chlorine to 1 ppm and pH to 7.2, add ascorbic acid at 1 lb per 10,000 gal, then a sequestrantNatural Chemistry metal stain procedure
Water test shows iron or copper above 0 ppm before treatingPre-treat with a sequestrant until metals read 0.00 ppm, then treat the stainJack's Magic FAQ
Copper reads 0.6 ppm or moreSkip copper algaecides; use a polyquat if you need oneLeslie's; our pool algaecide guide
Pool has a copper ionizerUse a sequestrant made for ion systems, not a standard oneJack's Magic FAQ; MAHC Annex 5.7.3.2.3
Fiberglass with dark spots that ignore vitamin C and ascorbic acidStop treating; ask a fiberglass pro about cobalt stainingRiver Pools
Raised blue-black spots on plaster that vitamin C does not touchTreat as black algae, not a stainNatural Chemistry; our black algae guide
Plaster under 28 days old shows a stainCall the plasterer before treating; follow the NPC start-up routineNPC start-up card
Stain survives two full metal treatments on old plasterPrice an acid wash or resurfacing; check the plaster firstPinch A Penny; our acid wash guide

Sources: Natural Chemistry; Natural Chemistry procedure; Jack’s Magic FAQ; Leslie’s; MAHC Annex; River Pools; NPC; Pinch A Penny. Download CSV

The last row is the expensive one. Pinch A Penny describes acid washing as the step for stains that chemical treatment cannot fix, and it removes a thin layer of plaster each time, about 1/16 inch by PoolDial’s estimate. Our pool acid wash guide shows how many washes a 3/8 inch plaster coat can take and when resurfacing is the better buy.

How do you keep pool stains from coming back?

Control metals at the source and hold the water balance. Test fill water for metals before filling, as the National Plasterers Council card directs, keep pH at 7.2 to 7.6 during treatment and inside CDC’s 7.0 to 7.8 at home, hold the saturation index at 0.0 to plus 0.3, and dose a sequestrant weekly: Natural Chemistry’s rate is 4 oz per 10,000 gallons.

  • Test fill water for pH, alkalinity, calcium and metals and record it (NPC start-up card); well water is the usual iron source (Natural Chemistry).
  • Keep the saturation index at 0.0 to plus 0.3; NPC says a positive index causes mineral scaling and metal staining, and our calcium hardness guide shows the math.
  • Test copper before a copper algaecide and skip it at 0.6 ppm or more (Leslie’s); never add one to a pool with an ionizer (MAHC Annex).
  • Test metals before shocking: BioGuard says a shock dose or a pH rise is what drops dissolved metal onto the surface.
  • Skim leaves daily so tannins never sit, and brush the steps weekly.
  • Partial drains dilute metals; a 20,000 gallon refill cost $39.00 to $649.98 across 25 cities in October 2026, median $215.09 (cost to fill a pool research).

How we compiled this

In November 2026 we read 21 primary and maker documents: stain procedures and FAQs from Natural Chemistry, BioGuard, Jack’s Magic and Pinch A Penny, a fiberglass maker’s stain guide and care sheet, two warranties, two EPA labels, EPA’s secondary standards, the 2024 MAHC Annex, the NPC start-up card, CDC guidance, a city plaster specification and NIST conversions, plus two PC&S research reports, and compared seven competing guides. Doses for other pool sizes are our arithmetic. We did not test any product, and forum posts were used for question wording only.

Frequently Asked Questions

How do I get rid of stains in my pool?

Identify the stain first. If chlorine lightens it, raise chlorine to breakpoint and scrub. If a vitamin C tablet lightens it within 2 minutes, it is metal: lower chlorine to 1 ppm, add ascorbic acid at 1 lb per 10,000 gallons, then a sequestrant, per Natural Chemistry. White crust is scale, not a stain.

Does vitamin C remove pool stains?

It removes many metal stains, mostly iron, because vitamin C is ascorbic acid. Natural Chemistry uses a tablet as the test and sells ascorbic acid at 1 lb per 10,000 gallons for floor and wall stains. It does nothing to organic stains, black algae or cobalt staining under fiberglass gelcoat (River Pools).

Will shock remove pool stains?

Only organic ones. Natural Chemistry treats leaf and debris stains by raising chlorine to breakpoint and scrubbing. Shock can make metal stains worse: BioGuard says a shock dose can turn dissolved metals insoluble so they drop onto the surface, and two makers say not to shock for at least 1 week after a metal treatment.

What causes brown stains on pool steps?

Usually leaves and debris, or iron. Steps hold leaves in still water, which leaves tannin stains that chlorine lightens. If vitamin C lightens the spot within 2 minutes instead, it is metal; Natural Chemistry suggests its citric acid STAINfree for minor stains on small areas or steps. EPA ties reddish staining to iron above 0.3 mg/L.

How do you remove iron stains from a pool floor?

Lower chlorine to 1 ppm and pH to 7.2 to 7.6, then add ascorbic acid at 1 lb per 10,000 gallons as close to the stain as possible with the pump off overnight, per Natural Chemistry. Brush, vacuum, add METALfree at 1 L per 20,000 gallons, clean the filter and do not shock for a week.

How do you remove pool stains without draining?

Treat the water. Organic stains respond to breakpoint chlorine and brushing; metal stains respond to ascorbic or citric acid in the water followed by a sequestrant, which holds the metal in solution so the filter can catch it. Draining is the step for stains that two in-water treatments do not move, and only on plaster.

What do copper stains in a pool look like?

Blue, blue-green or teal, per Pinch A Penny and River Pools, and EPA links blue-green staining to copper above 1.0 mg/L. Gray or black flat stains can be oxidized copper. Copper usually comes from algaecides, corroded heater parts or an ionizer; Leslie’s says staining may start above 0.6 ppm.

How do you remove stains from a fiberglass pool?

Wipe with a soft sponge first, then test. River Pools treats metal stains with chlorine at 0.0 ppm, pH near 7.2 and about 1 lb of ascorbic acid per 10,000 gallons for 24 hours, then a sequestrant. Avoid wire brushes and draining: Latham’s warranty is voided if water drops below the skimmer outlet.

Sources

  1. Natural Chemistry. Metal Stain Removal Procedure (STAINfree, METALfree). Accessed 2026-11-02.
  2. Natural Chemistry. Staining: stain identification and removal. Accessed 2026-11-02.
  3. BioGuard. Metal Staining. Accessed 2026-10-19.
  4. Pinch A Penny. How to Identify and Remove Pool Stains (June 6, 2022). Accessed 2026-11-02.
  5. Pinch A Penny. What is acid washing a pool? (June 13, 2018). Accessed 2026-11-02.
  6. Jack's Magic. Frequently Asked Questions. Accessed 2026-11-02.
  7. River Pools. How to Remove Stains from a Fiberglass Pool (updated April 9, 2026). Accessed 2026-11-02.
  8. River Pools. Fiberglass Pool Care Guide (2026 update). Accessed 2026-11-02.
  9. Latham Pool Products. Latham Fiberglass Pools Limited Lifetime Warranty (rev. 4/26). Accessed 2026-11-02.
  10. GLI Pool Products. 20 Year Liner Warranty Card. Accessed 2026-11-02.
  11. Thursday Pools. Fiberglass Pool Maintenance Tools and Cleaning Equipment (updated September 17, 2026). Accessed 2026-10-19.
  12. U.S. EPA Pesticide Product Label System. BioGuard Spot Kill, EPA Reg. No. 5185-441 (label May 22, 2024). Accessed 2026-10-19.
  13. U.S. EPA Pesticide Product Label System. Swimtrine, EPA Reg. No. 8959-2 (label April 14, 2025). Accessed 2026-11-01.
  14. U.S. EPA. Secondary Drinking Water Standards: Guidance for Nuisance Chemicals (updated May 26, 2026). Accessed 2026-11-01.
  15. CDC. 2024 Model Aquatic Health Code, 5th Edition, Annex. Accessed 2026-11-02.
  16. National Plasterers Council. Pool Start-Up Procedures card (rev. 03-2021). Accessed 2026-10-26.
  17. CDC. Home Pool and Hot Tub Water Treatment and Testing (May 10, 2024). Accessed 2026-11-01.
  18. Leslie's. How to Treat Black Algae in Your Pool. Accessed 2026-11-01.
  19. PoolDial. Acid Wash vs Replaster. Accessed 2026-11-02.
  20. City of Gulf Shores, Alabama. Swimming Pool Tile and Plaster Preparation, Gulf Shores Recreation Center pool resurfacing specification. Accessed 2026-11-02.
  21. NIST. Approximate Conversions from U.S. Customary Measures to Metric. Accessed 2026-11-01.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.