Skip to content
Backyard fiberglass pool with a smooth light blue shell and clear water
Guide: fiberglass pool repair

Fiberglass Pool Repair: Diagnose Cracks, Blisters and Bulges, Then Fix or Claim

Fiberglass pool repair starts with the symptom: spider cracks and chips take a $300 to $400 gelcoat patch (Angi, 2026), leaks and blisters go to the maker's warranty, and the water stays above the skimmer.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓Symptom by symptomCause, warranty position, fix and cost from four maker warranties.
  • ✓Patch specsCatalyst ratios, cure times and sanding grits from repair instructions.
  • ✓Dated pricesKit, repair and resurfacing prices read in November 2026.
Quick answer
Most fiberglass damage is cosmetic: spider cracks and chips are patched with gelcoat at 2% MEKP for $300 to $400 by a pro (Angi, July 2026). Leaking cracks and osmotic blisters are warranty claims with written notice due in 10 to 30 days. Never let the water drop below the skimmer: that voids Latham, River and Thursday warranties.
$300 to $400
Pro gelcoat repair
2% MEKP
Gelcoat catalyst
$7,000 to $15,000
Resurfacing

Key takeaways

  • Spider and star cracks stop in the 27 to 30 mil gelcoat (River Pools) and are excluded from the Latham, River and Thursday warranties, so they are the owner’s repair: about $300 to $400 by a pro, per Angi (July 2026).
  • A pool gelcoat patch is catalyzed at 2% MEKP, 20 ml per litre, hardens in 1 to 3 hours and is sanded at 400, 800 and 1,200 grit, per the 1st Direct Pools repair guide written for Leisure Pools shells.
  • Never lower the water below the skimmer to reach a repair: that voids the Latham, River Pools and Thursday Pools warranties in their own words.
  • Leaking cracks and osmotic blisters are the maker’s problem if you report them in time: written notice within 10 days for Latham, 30 days for River and Thursday, and 15 days by registered mail for San Juan.
  • River Pools’ 2026 care guide blames most fading and whitening on calcium combined with high pH and chlorine, and says to correct pH before it reaches 7.6.
  • Resurfacing a whole shell runs from about $1,500 for pro epoxy paint to $10,000 to $13,000 for a polymer coating (River Pools), and $7,000 to $15,000 in HomeGuide‘s range.

Can a fiberglass pool be repaired?

Yes. Gelcoat cracks, chips, fading and stains are field repairs, and leaking cracks and osmotic blisters are warranty repairs when the maker’s terms are met. The catch is who may do the work: Latham excludes repairs by anyone but its authorized representative or an approved contractor (section 8h), and San Juan voids coverage if anyone other than the manufacturer repairs the shell.

Fiberglass pool repair by symptom: cause, warranty position, fix and cost, from maker documents and dated prices
SymptomCause named in the maker documentWarranty positionFixDIY costPro cost (source, date)
Spider or star cracks: fine web or star lines in the gelcoatPressure beyond what the gelcoat can flex: installation (most common), uneven base, manufacturing or shipping (River Pools, Apr 2026); impact (1st Direct Pools)Excluded: hairline cracks (River, Thursday, Latham 8j); spider cracks in the beam (Latham 8p); gelcoat cracking (San Juan)Grind along the crack to gelcoat depth, fill with gelcoat at 2% MEKP, sand 400, 800, 1200 grit, compound$76.97 kit (Evercoat 108000, Fisheries Supply, Nov 2026)$300 to $400 gel coat repair (Angi, Jul 2026)
Chips and gouges from an impactImpact or excessive movement (1st Direct Pools)Not a structural or blister defect; cosmetic exclusions applyGel paste with 4 drops hardener per teaspoon, cover with release film about 1 hour, wet sand 600 grit (Evercoat)$76.97 kit$300 to $400 (Angi, Jul 2026)
Crack that leaks: water loss beyond evaporationStructural failure: fracture, void or crack from a manufacturing defect (Latham section 2)Covered for defects: Latham lifetime (original buyer), River no end date, Thursday 35 years, San Juan 25 yearsWritten notice to the maker; repair by its authorized representative; underwater epoxy putty only as a stopgapWaterWeld putty sets in 15 to 25 minutes (J-B Weld); price not published on the page we read$1,000 to $5,000 out of warranty (American Fiberglass Pools, Mar 2025)
Osmotic blisters: raised bubbles, dime size or smallerWater passes the gelcoat, reacts with polyester resin and cannot pass back out (River Pools; West System)Covered: Latham lifetime (original buyer), River and Thursday 15 years; San Juan excludes gelcoat bubblingSurface warranty claim first; out of warranty, grind open, dry and refill, or resurfaceNot a DIY job across a whole shell$7,000 to $15,000 to resurface (HomeGuide, Apr 2025)
Fading, chalking or whiteningpH above 7.6, calcium with high pH and chlorine (River care guide, 2026); salt systems raise whitening risk (Thursday)Excluded by Latham, River and Thursday; San Juan covers staining, discoloration and excessive fading from defects for 10 yearsRebalance water; San Juan allows a professional boat polish for uniform dulling; recoat if rough$257.99 per 2 gal epoxy kit (Ramuc EP Hi-Build, YourPoolHQ, Nov 2026)About $1,500 epoxy paint (River Pools, 2020) to $10,000 to $13,000 polymer (River Pools)
Wall bulging inwardSaturated sand backfill liquefies and pushes harder than the water inside (River Pools, Jul 2025)Excluded when backfill was not to spec (River, Thursday)Excavate behind the wall, brace, refill with crushed stone; keep water above the skimmerNot a DIY jobNo published price found; get written bids
Stains: rust, brown, green or black spotsMetals and calcium in the water (River care guide, 2026)Excluded: staining (Latham 8j, River, Thursday)In-water ascorbic acid treatment, no draining (see our pool stains guide)Doses by pool size in our pool stains guideService call at $45 to $65 per hour (Angi)

Sources: Latham CWP107.26 rev. 4/26, River Pools Rev0423, Thursday Pools Rev. 10.1.26, San Juan warranty, River Pools (Apr 2026), River care guide 2026, 1st Direct Pools, Angi, Fisheries Supply, American Fiberglass Pools, HomeGuide, YourPoolHQ; read November 2026. Download CSV

Fiberglass pool repair: key numbers with source and date
FactFigureSourceDate
Gelcoat thickness sprayed at the factory27 to 30 milsRiver Pools manufacturing pageRead Nov 2026
Vinyl ester barrier behind the gelcoatAbout 100 to 120 milsRiver Pools, osmotic blister articleRead Nov 2026
MEKP catalyst for a pool gelcoat patch2% (20 ml per litre of gelcoat)1st Direct Pools repair guide (Leisure Pools distributor)2008
Pro gel coat repair of dings, scratches and cracks$300 to $400AngiUpdated Jul 9, 2026
Pool repair labor$45 to $65 per hourAngiUpdated Jul 9, 2026
DIY gelcoat repair kit (Evercoat 108000)$76.97Fisheries SupplyNov 10, 2026
Fiberglass pool resurfacing$7,000 to $15,000HomeGuideApr 25, 2025
Water level that voids Latham, River and Thursday warrantiesBelow the skimmerMaker warrantiesRev. 4/26; Rev0423; Rev. 10.1.26
Written notice deadline after you find a defect10 days (Latham), 15 days (San Juan), 30 days (River, Thursday)Maker warrantiesCurrent documents

Sources: River Pools, River Pools osmotic blisters, 1st Direct Pools, Angi, Fisheries Supply, HomeGuide, Latham, River Pools Rev0423, Thursday, San Juan. Download CSV

Each row maps a symptom to the cause the maker itself names, because that cause decides who pays. River Pools lists its four most common problems as mismatched repairs on colored gelcoats, spider cracks, bulging walls and plumbing leaks from settling (River Pools, updated April 9, 2026). Only one of those, a leak from a manufacturing defect, is a warranty item; the rest trace to installation, backfill or water chemistry.

Color is the hidden cost of any patch. River Pools says metallic and flake finishes are hard to match outside the factory, while solid gelcoats go on in one layer and match more easily, and Latham’s warranty (section 8q) accepts shade variance after its own repairs. Before a patch, ask the repairer to test the color on a hidden spot such as the back of a step.

How do you tell a cosmetic crack from a structural one?

Check two things: depth and water loss. A spider crack stays inside the 27 to 30 mil gelcoat and the water level holds. A structural crack runs through the laminate, and Latham defines structural failure as water loss from a fracture, void or crack caused by a manufacturing defect. If the pool drops faster than evaporation, treat the crack as structural until a leak test says otherwise.

Five defects by the shell layer they reach: gelcoat 27 to 30 mils and vinyl ester barrier about 100 to 120 mils (River Pools); backfill specs from River Pools (July 2025) and Thursday Pools (Rev. 10.1.26).
Five defects by the shell layer they reach: gelcoat 27 to 30 mils and vinyl ester barrier about 100 to 120 mils (River Pools); backfill specs from River Pools (July 2025) and Thursday Pools (Rev. 10.1.26).
Which layer each defect reaches, and where the repair happens
DefectLayer it reachesWhat you seeWhere the repair happensSource
1 Spider or star crackGelcoat only (27 to 30 mils)Fine web or star linesRegrind and refill the gelcoatRiver Pools; 1st Direct Pools
2 Osmotic blisterGelcoat and the resin behind itRaised bubble, dime size or smallerGrind open, dry, refill; surface warranty claimRiver Pools; West System
3 Structural crackThrough the laminateWater lossMaker's authorized repairLatham warranty section 2
4 Fading, chalking, whiteningTop of the gelcoatChalky, faded or white filmWater balance, polish or recoatRiver care guide 2026; San Juan; Thursday
5 Wall bulgeWhole wall, from the backfill sideWall pushed inwardExcavate and regravel behind the shellRiver Pools (Jul 2025); Thursday warranty

Sources: River Pools manufacturing page, River Pools osmotic blisters, Latham warranty section 2, West System (2004), River Pools sand vs gravel (Jul 2025), Thursday warranty. Download CSV

  1. Mark and measure the water levelPut tape at the waterline and read it after 24 hours with the pump off; compare the drop with your local evaporation rate before blaming the shell.
  2. Look at where the crack sitsCracks on the beam under the coping are excluded by Latham (section 8p: crazing, spider cracks and chips in the beam are not cause for a claim).
  3. Watch it for 7 daysA crack that weeps, stains or lengthens, or a water loss that continues with the pump off, needs a leak test before a warranty claim.
  4. Photograph it with a coin for scaleLatham and River both ask for photos with the claim; date every photo and keep your water test records.

Leak tests on plumbing, skimmers and lights come before a shell claim, since River Pools names plumbing leaks from settling as one of its 4 most common fiberglass problems. The dye and bucket tests are laid out in our pool leak detection guide.

How can I fix cracks in my fiberglass pool?

Grind the crack out to the depth of the gelcoat, tape around it, fill it with matching gelcoat catalyzed at 2% MEKP, then sand and buff. The 1st Direct Pools guide, written for Leisure Pools shells, says the patch hardens in 1 to 3 hours and must pass an acetone rub before water touches it; an uncured patch turns white underwater.

  1. Keep the water above the skimmerWork only on cracks above the waterline, on steps or benches you can dry with the water at normal level; Latham, River and Thursday void their warranties below the skimmer.
  2. Grind along the crackUse a die grinder down to the thickness of the original gelcoat, about 27 to 30 mils on a River shell, so the new gelcoat locks into a clean groove.
  3. Tape and mixMask around the groove to allow for shrinkage. Mix gelcoat with 2% MEKP: 20 ml per litre, or 12 drops per ounce for Evercoat One Step Gel-Kote.
  4. Fill and screed flatApply with a blade and screed level with the tape. Evercoat gives about 15 minutes of working time at 72 to 75F.
  5. Let it hardenPull the tape and wait 1 to 3 hours, longer when cool. Cover small chip repairs with clear release film for about 1 hour so the surface cures tack free.
  6. Sand and buffWet sand at 400 grit until level, then 800 and 1,200 grit; finish with cutting compound. Evercoat’s chip kit instructions stop at 600 grit, compound and wax.
  7. Check the cureRub with acetone on a white rag. Color on the rag means wait an hour and retest; no cure after 6 hours means grind it out and start again.
Fiberglass pool repair materials compared: mix ratios, times and prep from maker documents
Product or methodUsed forMix or catalystWorking, set and fill timesFinish and prepSource and date
Pool gelcoat patch (1st Direct Pools guide)Star cracks2% MEKP: 20 ml per litreHard in 1 to 3 hours; acetone rub test; regrind if not cured at 6 hoursWet sand 400, then 800, then 1,200 grit; cutting compound1st Direct Pools, 2008
Evercoat One Step Finishing Gel-KoteGouges, chips, scratches12 drops MEKP per 1 ozAbout 15 minutes working time at 72 to 75FNo mold release needed for a full cureEvercoat training portal, read Nov 2026
Evercoat gelcoat repair kits 100668 and 108000Small chips4 drops hardener per teaspoon of gel pasteAbout 15 minutes working; remove film after about 1 hourClear release film; 600 grit wet sand; rubbing compound; waxEvercoat via Wholesale Marine (2009); $76.97 at Fisheries Supply, Nov 2026
J-B Weld WaterWeld epoxy puttyStopgap leak plug, sets under waterKnead two-part puttySets in 15 to 25 minutes, hard in 1 hourCan be sanded and paintedJ-B Weld, read Nov 2026
Insl-X Epoxy Pool Paint IG-40XXFull repaint1:1 by volume; 30 minute induction at 77FPot life 6 hours at 77F; fill after 7 days outdoors, 14 indoors; surface 50 to 100FScuff sand bare fiberglass with 150 to 180 grit; 350 to 400 sq ft per gallonBenjamin Moore TDS (2020); product page read Nov 2026
Ramuc EP Hi-Build epoxyFull repaintTwo parts, mechanically mixed3 hour pot life; fill after 5 to 7 days outdoors, 10 to 14 indoors150 to 200 sq ft per 2 gal kit bare, 300 to 350 recoat; $257.99YourPoolHQ listing, Nov 10, 2026

Sources: 1st Direct Pools (2008), Evercoat One Step Gel-Kote, Evercoat kit instructions via Wholesale Marine, Fisheries Supply, J-B Weld WaterWeld, Insl-X IG-40XX TDS, YourPoolHQ Ramuc listing; read November 10, 2026. Download CSV

Can you repair a fiberglass pool without draining it?

Yes for anything above the waterline, and that is the rule, not a shortcut. Latham, River and Thursday void their warranties if the water drops below the skimmer, and San Juan warns the shell may crack or buckle and tells owners not to drain it themselves. Below the waterline, a two-part epoxy putty such as J-B Weld WaterWeld, which sets under water in 15 to 25 minutes, holds as a stopgap.

A drained fiberglass shell is held in place only by its backfill, so groundwater can push it up. That is why Latham’s warranty puts draining, bracing and removing groundwater on the buyer when a covered repair needs an empty pool (section 10), and River Pools prints “Do not drain the pool!” in its owner warranty. Our how to drain a pool guide covers hydrostatic valves and discharge rules for the cases where a pro must do it.

What several fiberglass repair guides say vs what the maker documents say
What a repair guide saysWho says itWhat the primary document saysPrimary source
Drain the pool to 6 inches below the damaged areaPool Doctor of the Palm Beaches repair articleWater below the skimmer voids the warranty; San Juan says never drain it yourselfLatham 11a; River Rev0423; Thursday Rev. 10.1.26; San Juan
Apply gelcoat in 5 mil coats to 20 to 25 milsPool Doctor of the Palm BeachesFactory gelcoat is sprayed to 27 to 30 milsRiver Pools manufacturing page
Fiberglass gelcoat can only be applied in a factoryHomeGuide (Apr 2025)Field gelcoat patches at 2% MEKP are standard for star cracks; whole-shell recoats use paint or polymer1st Direct Pools guide (2008)
Epoxy paint only bonds to a bare surfaceRiver Pools resurfacing article (2020)Insl-X and Ramuc both list application over previous epoxy coatings in sound conditionInsl-X TDS; Ramuc listing
Keep calcium hardness at 150 to 200 ppmRiver Pools owner warranty Rev0423River's 2026 care guide says under 120 ppm; Latham asks for 250 to 350 ppmRiver care guide 2026; Latham CWP107.26

Sources: Pool Doctor of the Palm Beaches, HomeGuide, River Pools (2020), Latham, River Pools Rev0423, Thursday, San Juan, River Pools manufacturing, 1st Direct Pools, Insl-X TDS, Ramuc listing, River care guide 2026. Download CSV

The calcium row matters for repairs, because the wrong water undoes a new patch or paint job. River Pools’ 2026 care guide asks for calcium under 120 ppm and pH 7.2 to 7.4, its older Rev0423 warranty lists 150 to 200 ppm, and Latham asks for 250 to 350 ppm, so follow the current document from your own maker. Target ranges for every reading are in our pool chemical levels chart.

What should you do about fiberglass pool blisters?

File a surface warranty claim before anyone grinds them. Osmotic blisters are raised bubbles, usually dime size or smaller, that form when water passes the gelcoat and reacts with polyester resin behind it. Latham covers them for the original buyer for life, River and Thursday for 15 years; San Juan’s structural warranty excludes gelcoat bubbling.

River Pools says blisters were common before vinyl ester resin became standard and are now “all but extinct in new pools”, which it credits to a vinyl ester layer of about 100 to 120 mils (River Pools). West System, a marine epoxy maker, explains the chemistry in its 2004 repair manual: water reaching unreacted resin forms an acidic solution that breaks ester links, and warmer water speeds it up (West System).

Molded steps and benches sit above the skimmer line, so cracks there can be repaired with the pool full, the only water level the Latham, River and Thursday warranties allow.
Molded steps and benches sit above the skimmer line, so cracks there can be repaired with the pool full, the only water level the Latham, River and Thursday warranties allow.

Out of warranty, the West System boat method shows why a full repair is a pro job: abrade with 80 grit, grind or peel the gelcoat off, dry the laminate while monitoring moisture readings, keep the surface temperature under 50C, then rebuild with epoxy and fairing. For a pool, that work happens in an empty shell, so it is usually priced as resurfacing at $7,000 to $15,000 (HomeGuide, April 2025).

Why is my fiberglass pool fading, chalky or white?

Most often the water. River Pools’ 2026 care guide says calcium combined with high pH and chlorine causes most discoloration, and tells owners to correct pH before 7.6 because damage past that point is permanent and not covered. Thursday Pools warns that salt systems greatly raise the risk of whitening when chemistry drifts, and whitening is excluded from its warranty.

  • Chalky film that wipes off: check calcium and pH first; River’s 2026 guide recommends a chelating stain and scale product when calcium is above 120 ppm.
  • Even dulling from sun: San Juan says uniform dulling of its Iridium finish can be re-polished with a professional boat polish.
  • Faded paint on a previously painted shell: Insl-X states that its epoxy pool coating, like any epoxy, will chalk and fade over time under ultraviolet light.
  • Spots of color: metals or organics, treated in the water; see our pool stains guide for the ascorbic acid test and doses.

San Juan is the one maker here with a finish-color promise: its surface warranty covers staining, discoloration and excessive fading from defects for 10 years, but not gradual change from chemicals or weather, and it needs notice within 5 days of discovery by registered mail. Latham’s section 8j excludes fading, staining and discoloration outright.

How do you fix a bulging fiberglass pool wall?

From the outside. River Pools traced its own bulges to sand backfill: saturated sand liquefies and, being heavier than the water inside, pushes the wall in. The fix is to excavate behind the wall with the pool full, brace it, and refill with clean crushed stone, 3/4 in or smaller per River, or 3/8 in to 1 1/2 in washed chip stone per Thursday’s warranty.

  1. Keep the pool fullThe water inside is what holds the wall’s shape; lowering it to inspect the bulge adds load and voids the Latham, River and Thursday warranties.
  2. Check the drainage firstThursday requires an 8 in perforated well pipe set 12 in below the deep end on 2 in of gravel; if it is missing or clogged, groundwater will refill the backfill.
  3. Excavate behind the bulgeThe installer removes the saturated backfill along the affected wall, down past the bulge.
  4. Brace and refillPush the wall back to line and refill with crushed stone, which River says performs the same wet or dry; Thursday’s warranty has backfill placed, alternating, to within 12 in of the water level.
  5. Replace the deck sectionDeck or coping removed for access is outside every warranty here; price it in the same bid.

We found no published price for bulge repair, and forum figures are not a source. Ask for a written bid that names the backfill material and size (River: crushed stone 3/4 in or smaller; Thursday: 3/8 in to 1 1/2 in washed chip stone), the well pit depth and whether deck and coping replacement are included, then compare it with the shell’s warranty status before you sign.

Get quotes for fiberglass pool repair

How much does it cost to fix a fiberglass pool?

A spot gelcoat repair costs $300 to $400 from a pro (Angi, July 2026) or $76.97 for a DIY kit (Fisheries Supply, November 2026). Out-of-warranty structural crack and leak repairs run $1,000 to $5,000 (American Fiberglass Pools, 2025). A whole-shell resurface ranges from about $1,500 for pro epoxy paint to $10,000 to $13,000 for a polymer coating (River Pools).

What a spot repair costs, from a $77 kit to a structural fixUS dollars; DIY kit price on November 10, 2026
What a spot repair costs, from a $77 kit to a structural fixRange chart: DIY gelcoat kit $76.97; pro gel coat repair $300 to $400; repaint after repair about $800; refill and chemicals $300 to $700; structural crack or leak repair $1,000 to $5,000.$0$1,250$2,500$3,750$5,000DIY gelcoat kit (Evercoat 108000): $77.0 to $77.0DIY gelcoat kit (Evercoat 108000)Pro gel coat repair (Angi 2026): $300 to $400Pro gel coat repair (Angi 2026)Repaint after a repair (Angi 2026): $800 to $800Repaint after a repair (Angi 2026)Refill and chemicals (AFP 2025): $300 to $700Refill and chemicals (AFP 2025)Structural crack or leak (AFP 2025): $1,000 to $5,000Structural crack or leak (AFP 2025)

Structural figures are out-of-warranty prices; a covered defect is repaired by the maker.

Source: Fisheries Supply (Nov 10, 2026), Angi (updated Jul 9, 2026), American Fiberglass Pools (Mar 8, 2025). Download chart data (CSV)

Fiberglass pool repair costs by job, with publisher and date
JobPriceWho published itDate
Gelcoat repair kit, DIY (Evercoat 108000)$76.97Fisheries Supply (retailer)Nov 10, 2026
Pro gel coat repair of dings, scratches, cracks$300 to $400AngiUpdated Jul 9, 2026
Repaint after a gel coat repairAbout $800 moreAngiUpdated Jul 9, 2026
Pool repair labor$45 to $65 per hourAngiUpdated Jul 9, 2026
Structural repairs (cracks, leaks)$1,000 to $5,000American Fiberglass Pools (contractor)Mar 8, 2025
Water refill and chemicals after a repair$300 to $700American Fiberglass PoolsMar 8, 2025
San Juan warranty service visit$75 trip charge per visitSan Juan Pools warrantyCurrent page

Sources: Fisheries Supply, Angi (Wayback capture, Aug 2026), American Fiberglass Pools, San Juan Pools. Download CSV

Published prices to resurface a fiberglass pool, by methodUS dollars per pool; single published figures plotted as a point
Published prices to resurface a fiberglass pool, by methodRange chart: epoxy paint pro about $1,500; DIY resurfacing $1,500 to $4,000; gel coat resurfacing $5,000 to $8,000; full resurfacing about $6,500; epoxy or polymer $7,000 to $12,000; HomeGuide $7,000 to $15,000; ecoFINISH $10,000 to $13,000.$0$3,750$7,500$11,250$15,000Epoxy paint, pro (River Pools 2020): $1,500 to $1,500Epoxy paint, pro (River Pools 2020)DIY resurfacing (AFP 2025): $1,500 to $4,000DIY resurfacing (AFP 2025)Gel coat resurfacing (AFP 2025): $5,000 to $8,000Gel coat resurfacing (AFP 2025)Full resurfacing (Angi 2026): $6,500 to $6,500Full resurfacing (Angi 2026)Epoxy or polymer coating (AFP 2025): $7,000 to $12,000Epoxy or polymer coating (AFP 2025)Fiberglass resurfacing (HomeGuide 2025): $7,000 to $15,000Fiberglass resurfacing (HomeGuide 2025)ecoFINISH polymer (River Pools): $10,000 to $13,000ecoFINISH polymer (River Pools)

Each publisher prices a different pool and scope; none states a sample size.

Source: River Pools (2020), American Fiberglass Pools (Mar 2025), Angi (Jul 2026), HomeGuide (Apr 2025); read November 2026. Download chart data (CSV)

Fiberglass pool resurfacing options: published prices and claimed life
OptionPublished priceLife or wait claimedWho published itDate
Epoxy pool paint, proAbout $1,500Up to 5 years; pool usable after up to 2 weeksRiver PoolsMar 25, 2020
Epoxy pool paint, DIY materials$257.99 per 2 gal Ramuc kitUp to eight or more years (seller claim); fill after 5 to 7 daysYourPoolHQNov 10, 2026
DIY resurfacing, all in$1,500 to $4,0003 to 5 days of laborAmerican Fiberglass PoolsMar 8, 2025
Basic gel coat resurfacing, pro$5,000 to $8,000Not statedAmerican Fiberglass PoolsMar 8, 2025
Full resurfacing, proAbout $6,500Not statedAngiJul 9, 2026
Epoxy or polymer coating, pro$7,000 to $12,000Not statedAmerican Fiberglass PoolsMar 8, 2025
Fiberglass resurfacing, pro$7,000 to $15,000Not statedHomeGuideApr 25, 2025
ecoFINISH thermoplastic polymer, pro$10,000 to $13,000 minimumRefill right awayRiver PoolsMar 25, 2020

Sources: River Pools (Mar 25, 2020), YourPoolHQ, American Fiberglass Pools, Angi, HomeGuide. Download CSV

The spread is wider than the jobs. River Pools prices pro epoxy paint at about $1,500 while American Fiberglass Pools puts epoxy or polymer at $7,000 to $12,000, and Angi adds about $800 to repaint after a spot repair. None states a pool size or sample. Ask each bidder for square footage, number of coats and the product data sheet.

Worked example: epoxy paint for a 14 x 28 ft fiberglass pool, two coats
LineInput or resultHow it is worked out
Pool size (example)14 x 28 ft, 4.5 ft average depthPC&S example, not a model
Floor area392 sq ft14 x 28
Wall area378 sq ft2 x (14 + 28) x 4.5
Surface to coat770 sq ft392 + 378; steps and curves ignored
Coat 1 at the bare rate (150 to 200 sq ft per kit)4 to 6 kits770 / 200 = 3.9; 770 / 150 = 5.1; rounded up
Coat 2 at the recoat rate (300 to 350 sq ft per kit)3 kits770 / 350 = 2.2; 770 / 300 = 2.6; rounded up
Kits for two coats7 to 9 kits4 + 3 to 6 + 3
Paint cost at $257.99 per kit$1,805.93 to $2,321.917 x 257.99 to 9 x 257.99
Compare: pro epoxy paint (River Pools, 2020)About $1,500Published figure
Compare: pro polymer coating (River Pools)$10,000 to $13,000Published minimum

Sources: coverage and price from the Ramuc EP Hi-Build listing at YourPoolHQ (Nov 10, 2026); pro figures from River Pools. PC&S arithmetic; the listing does not state a coat count. Download CSV

Paint is not a gelcoat: a painted fiberglass pool becomes a painted pool, with Insl-X calling for a scuff sand at 150 to 180 grit, 7 days before filling and stripping once 4 or more aged layers build up. New shell prices for a replacement, if repair stops making sense, are in our fiberglass pool cost guide, and finishes for concrete pools are compared in pool resurfacing cost.

Does a repair void your fiberglass pool warranty?

It can. Latham does not cover repairs by anyone other than its authorized representative or an approved contractor (section 8h), River excludes repairs by anyone but its own authorized representative, and San Juan withdraws coverage entirely if anyone else repairs the shell. Report the defect in writing first, then wait for the maker to name the repairer.

How to file a fiberglass pool warranty claim, maker by maker
MakerNotice deadline and methodWhat to sendWho pays to drain and refillRepairs by others
Latham (and Narellan)Written notice within 10 days of discovery; 5 days for transport damage; email or online claim formName and contact, serial number (on the second step), install date and builder, description and photosBuyer drains, braces and removes groundwater (section 10); no refill compensation (8r)Not covered unless by an authorized representative or approved contractor (8h)
River PoolsIn writing within 30 days of the defectDated proof of purchase, photos, a regularly updated operation and service recordBuyer empties and refills; pool must be empty for serviceExcluded unless by an authorized River representative
Thursday PoolsIn writing within 30 days of identifying the defectDated proof of purchase, operation and service records, photos if inspection is requestedThursday not liable for refill water and chemicalsDamage caused by third parties voids coverage
San Juan PoolsRegistered mail within 15 days; surface claims within 5 daysGet the authorized repairer's name in writing before any repairNot responsible for water or chemicals; $75 trip charge per visitNo warranty if anyone other than the manufacturer repairs the shell

Sources: Latham CWP107.26 rev. 4/26 sections 6, 8, 10; River Pools Rev0423; Thursday Pools Rev. 10.1.26; San Juan warranty page; read November 2026. Download CSV

Cosmetic patches above the waterline are the gray zone: the cracks themselves are excluded, so a careful owner repair rarely affects a claim, but a botched grind into the laminate can. Coverage terms, transfer rules and lifespans by maker are compared in our fiberglass pool guide. None of the 83 US pool product recalls in our pool product recalls registry involves a fiberglass shell.

Which fiberglass pool repair fits your situation?

Match the symptom to the row. Cosmetic cracks and chips are owner repairs; leaks and blisters go to the maker in writing within its deadline; chalking starts with water chemistry; a bulge is an excavation job with the pool kept full. Anything that needs the water below the skimmer waits for the maker’s written approval.

Fiberglass pool repair decision table
If your situation isDo thisWhy (source)
Fine web or star cracks above the waterline, no water lossPatch the gelcoat yourself or hire a $300 to $400 repair; or leave itCosmetic; excluded from Latham, River and Thursday warranties
Pool loses more water than evaporation and you can see a crackPhotograph it and send written notice to the maker before anyone repairs itLatham 10 days, River and Thursday 30 days, San Juan 15 days by registered mail
Raised bubbles, dime size or smallerFile a surface warranty claim; do not grind them open firstLatham lifetime (original buyer); River and Thursday 15 years
Surface chalky, faded or white but smoothBring pH to 7.2 to 7.4 and calcium under 120 ppm; polishRiver 2026 care guide; San Juan allows a professional boat polish
Surface rough, peeling or repainted 4 or more timesResurface: epoxy paint about $1,500 pro, polymer $10,000 to $13,000River Pools; Insl-X says 4 or more aged layers may need stripping
Wall bowed inwardCall the installer to excavate and regravel; never lower the water to lookRiver Pools (Jul 2025); Thursday backfill spec
Repair would need the water below the skimmerGet the maker's written approval and a braced, dewatered drain plan firstLatham, River and Thursday void the warranty below the skimmer

Sources: Latham, River Pools, Thursday Pools, San Juan, River care guide 2026, River Pools (Jul 2025), Insl-X TDS, Angi. Download CSV

The same decision logic as a flowchart: leak first, then blisters, bulges, cracks and chalking. Deadlines from the Latham, River, Thursday and San Juan warranties.
The same decision logic as a flowchart: leak first, then blisters, bulges, cracks and chalking. Deadlines from the Latham, River, Thursday and San Juan warranties.

Pump, heater and plumbing faults that look like shell problems are triaged in our pool repair guide, with labor rates for each trade.

How we compiled this

We read four fiberglass maker warranties (Latham, River Pools, Thursday Pools, San Juan), River Pools’ 2026 care guide and four of its technical articles, one pool gelcoat repair guide, two gelcoat product instructions, two epoxy pool paint data sheets or listings and five dated price pages, all in November 2026. We did not test products or inspect pools. Forum threads were used only for question wording.

Frequently Asked Questions

Can a fiberglass pool be repaired?

Yes. Spider cracks, chips and fading are field repairs with gelcoat or paint, and leaking cracks and osmotic blisters are warranty repairs when the defect came from manufacturing. Latham, River and San Juan restrict who may repair the shell, so send written notice to the maker before any structural work, and keep the water above the skimmer.

How much does it cost to fix a fiberglass pool?

Angi puts a gel coat repair of dings, scratches and cracks at $300 to $400, updated July 2026, and a DIY Evercoat kit sold for $76.97 at Fisheries Supply on November 10, 2026. Out-of-warranty structural crack or leak repairs run $1,000 to $5,000 (American Fiberglass Pools, 2025); resurfacing runs $7,000 to $15,000 (HomeGuide).

How can I fix cracks in my fiberglass pool?

Grind the crack to the depth of the gelcoat, tape around it, fill with matching gelcoat mixed at 2% MEKP, about 20 ml per litre, and let it harden 1 to 3 hours. Wet sand at 400, 800 and 1,200 grit, buff, then pass an acetone rub test before the water touches it, per the 1st Direct Pools guide.

Will new fiberglass stick to old fiberglass?

Only to a clean, abraded surface. The 1st Direct Pools guide grinds a groove into old gelcoat before new gelcoat goes in, West System abrades with 80 grit before rebuilding, and Insl-X requires a 150 to 180 grit scuff sand on fiberglass before its epoxy paint. Paint or gelcoat over a glossy or chalky surface will not hold.

How long after a gelcoat repair can you swim?

Once the patch passes the acetone rub test: the 1st Direct Pools guide says gelcoat hardens in 1 to 3 hours, and a repair not cured after 6 hours must be ground out. Painted repairs take longer: Insl-X asks for 7 days before filling outdoors and 14 days indoors, and Ramuc lists 5 to 7 days outdoors.

Should I drain my fiberglass pool to fix a crack?

No. Latham, River Pools and Thursday Pools each void their warranties if the water falls below the skimmer, and San Juan warns the shell may crack or buckle if drained by anyone not authorized. Repair cracks above the waterline in place, use an underwater epoxy putty as a stopgap, and leave draining to the maker’s approved repairer.

Sources

  1. Latham Pool Products. Latham Fiberglass Pools Limited Lifetime Warranty (CWP107.26, rev. 4/26). Accessed 2026-11-08.
  2. River Pools. One-Time Transferable Limited Structural Warranty and 15-Year Surface Warranty (Rev0423). Accessed 2026-11-08.
  3. Thursday Pools. One-Time Transferable Limited 35 Year Structural Warranty (Rev. 10.1.26). Accessed 2026-11-08.
  4. San Juan Pools. Warranty. Accessed 2026-11-08.
  5. River Pools. Fiberglass Pool Care Guide (2026 update). Accessed 2026-11-10.
  6. River Pools. Top 4 Fiberglass Pool Problems and Solutions (updated April 9, 2026). Accessed 2026-11-08.
  7. River Pools. What Causes Osmotic Blisters on Fiberglass Pools. Accessed 2026-11-08.
  8. River Pools. Manufacturing: gel coat surface layer. Accessed 2026-11-10.
  9. River Pools. Fiberglass Pool Gel Coat Problems and Manufacturing Solutions (2011). Accessed 2026-11-10.
  10. River Pools. Installing a Fiberglass Pool on Sand vs Gravel (July 3, 2025). Accessed 2026-11-10.
  11. River Pools. How Much Does Inground Pool Resurfacing Cost? (March 25, 2020). Accessed 2026-11-10.
  12. West System. Gelcoat Blisters: A Guide to Osmosis Repair (5th ed., 2004). Accessed 2026-11-08.
  13. 1st Direct Pools. Repairing a Fibreglass Pool (2008). Accessed 2026-11-10.
  14. Evercoat. One Step Finishing Gel-Kote. Accessed 2026-11-10.
  15. Wholesale Marine. Instructions and Color Chart for Evercoat Gel Coat Repair (Evercoat text, 2009). Accessed 2026-11-10.
  16. Fisheries Supply. Evercoat 108000 gelcoat repair kit listing. Accessed 2026-11-10.
  17. J-B Weld. WaterWeld Epoxy Putty. Accessed 2026-11-10.
  18. Benjamin Moore. Insl-X Epoxy Pool Paint IG-40XX technical data sheet (2020). Accessed 2026-11-10.
  19. Benjamin Moore. Insl-X Epoxy Pool Paint product page. Accessed 2026-11-10.
  20. YourPoolHQ. Ramuc EP Hi-Build Epoxy Swimming Pool Paint, 2 gallon kit. Accessed 2026-11-10.
  21. Angi. How Much Do Swimming Pool Repairs Cost? (updated July 9, 2026; Wayback capture). Accessed 2026-11-10.
  22. American Fiberglass Pools. Fiberglass Pool Resurfacing Cost Guide (March 8, 2025). Accessed 2026-11-10.
  23. HomeGuide. How Much Does Pool Resurfacing Cost? (April 25, 2025). Accessed 2026-10-08.
  24. Pool Doctor of the Palm Beaches. Repair Your Damaged Fiberglass Pool. Accessed 2026-11-10.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.