
Fiberglass Pool Repair: Diagnose Cracks, Blisters and Bulges, Then Fix or Claim
Fiberglass pool repair starts with the symptom: spider cracks and chips take a $300 to $400 gelcoat patch (Angi, 2026), leaks and blisters go to the maker's warranty, and the water stays above the skimmer.
- ✓Symptom by symptomCause, warranty position, fix and cost from four maker warranties.
- ✓Patch specsCatalyst ratios, cure times and sanding grits from repair instructions.
- ✓Dated pricesKit, repair and resurfacing prices read in November 2026.
Key takeaways
- Spider and star cracks stop in the 27 to 30 mil gelcoat (River Pools) and are excluded from the Latham, River and Thursday warranties, so they are the owner’s repair: about $300 to $400 by a pro, per Angi (July 2026).
- A pool gelcoat patch is catalyzed at 2% MEKP, 20 ml per litre, hardens in 1 to 3 hours and is sanded at 400, 800 and 1,200 grit, per the 1st Direct Pools repair guide written for Leisure Pools shells.
- Never lower the water below the skimmer to reach a repair: that voids the Latham, River Pools and Thursday Pools warranties in their own words.
- Leaking cracks and osmotic blisters are the maker’s problem if you report them in time: written notice within 10 days for Latham, 30 days for River and Thursday, and 15 days by registered mail for San Juan.
- River Pools’ 2026 care guide blames most fading and whitening on calcium combined with high pH and chlorine, and says to correct pH before it reaches 7.6.
- Resurfacing a whole shell runs from about $1,500 for pro epoxy paint to $10,000 to $13,000 for a polymer coating (River Pools), and $7,000 to $15,000 in HomeGuide‘s range.
Can a fiberglass pool be repaired?
Yes. Gelcoat cracks, chips, fading and stains are field repairs, and leaking cracks and osmotic blisters are warranty repairs when the maker’s terms are met. The catch is who may do the work: Latham excludes repairs by anyone but its authorized representative or an approved contractor (section 8h), and San Juan voids coverage if anyone other than the manufacturer repairs the shell.
| Symptom | Cause named in the maker document | Warranty position | Fix | DIY cost | Pro cost (source, date) |
|---|---|---|---|---|---|
| Spider or star cracks: fine web or star lines in the gelcoat | Pressure beyond what the gelcoat can flex: installation (most common), uneven base, manufacturing or shipping (River Pools, Apr 2026); impact (1st Direct Pools) | Excluded: hairline cracks (River, Thursday, Latham 8j); spider cracks in the beam (Latham 8p); gelcoat cracking (San Juan) | Grind along the crack to gelcoat depth, fill with gelcoat at 2% MEKP, sand 400, 800, 1200 grit, compound | $76.97 kit (Evercoat 108000, Fisheries Supply, Nov 2026) | $300 to $400 gel coat repair (Angi, Jul 2026) |
| Chips and gouges from an impact | Impact or excessive movement (1st Direct Pools) | Not a structural or blister defect; cosmetic exclusions apply | Gel paste with 4 drops hardener per teaspoon, cover with release film about 1 hour, wet sand 600 grit (Evercoat) | $76.97 kit | $300 to $400 (Angi, Jul 2026) |
| Crack that leaks: water loss beyond evaporation | Structural failure: fracture, void or crack from a manufacturing defect (Latham section 2) | Covered for defects: Latham lifetime (original buyer), River no end date, Thursday 35 years, San Juan 25 years | Written notice to the maker; repair by its authorized representative; underwater epoxy putty only as a stopgap | WaterWeld putty sets in 15 to 25 minutes (J-B Weld); price not published on the page we read | $1,000 to $5,000 out of warranty (American Fiberglass Pools, Mar 2025) |
| Osmotic blisters: raised bubbles, dime size or smaller | Water passes the gelcoat, reacts with polyester resin and cannot pass back out (River Pools; West System) | Covered: Latham lifetime (original buyer), River and Thursday 15 years; San Juan excludes gelcoat bubbling | Surface warranty claim first; out of warranty, grind open, dry and refill, or resurface | Not a DIY job across a whole shell | $7,000 to $15,000 to resurface (HomeGuide, Apr 2025) |
| Fading, chalking or whitening | pH above 7.6, calcium with high pH and chlorine (River care guide, 2026); salt systems raise whitening risk (Thursday) | Excluded by Latham, River and Thursday; San Juan covers staining, discoloration and excessive fading from defects for 10 years | Rebalance water; San Juan allows a professional boat polish for uniform dulling; recoat if rough | $257.99 per 2 gal epoxy kit (Ramuc EP Hi-Build, YourPoolHQ, Nov 2026) | About $1,500 epoxy paint (River Pools, 2020) to $10,000 to $13,000 polymer (River Pools) |
| Wall bulging inward | Saturated sand backfill liquefies and pushes harder than the water inside (River Pools, Jul 2025) | Excluded when backfill was not to spec (River, Thursday) | Excavate behind the wall, brace, refill with crushed stone; keep water above the skimmer | Not a DIY job | No published price found; get written bids |
| Stains: rust, brown, green or black spots | Metals and calcium in the water (River care guide, 2026) | Excluded: staining (Latham 8j, River, Thursday) | In-water ascorbic acid treatment, no draining (see our pool stains guide) | Doses by pool size in our pool stains guide | Service call at $45 to $65 per hour (Angi) |
Sources: Latham CWP107.26 rev. 4/26, River Pools Rev0423, Thursday Pools Rev. 10.1.26, San Juan warranty, River Pools (Apr 2026), River care guide 2026, 1st Direct Pools, Angi, Fisheries Supply, American Fiberglass Pools, HomeGuide, YourPoolHQ; read November 2026. Download CSV
| Fact | Figure | Source | Date |
|---|---|---|---|
| Gelcoat thickness sprayed at the factory | 27 to 30 mils | River Pools manufacturing page | Read Nov 2026 |
| Vinyl ester barrier behind the gelcoat | About 100 to 120 mils | River Pools, osmotic blister article | Read Nov 2026 |
| MEKP catalyst for a pool gelcoat patch | 2% (20 ml per litre of gelcoat) | 1st Direct Pools repair guide (Leisure Pools distributor) | 2008 |
| Pro gel coat repair of dings, scratches and cracks | $300 to $400 | Angi | Updated Jul 9, 2026 |
| Pool repair labor | $45 to $65 per hour | Angi | Updated Jul 9, 2026 |
| DIY gelcoat repair kit (Evercoat 108000) | $76.97 | Fisheries Supply | Nov 10, 2026 |
| Fiberglass pool resurfacing | $7,000 to $15,000 | HomeGuide | Apr 25, 2025 |
| Water level that voids Latham, River and Thursday warranties | Below the skimmer | Maker warranties | Rev. 4/26; Rev0423; Rev. 10.1.26 |
| Written notice deadline after you find a defect | 10 days (Latham), 15 days (San Juan), 30 days (River, Thursday) | Maker warranties | Current documents |
Sources: River Pools, River Pools osmotic blisters, 1st Direct Pools, Angi, Fisheries Supply, HomeGuide, Latham, River Pools Rev0423, Thursday, San Juan. Download CSV
Each row maps a symptom to the cause the maker itself names, because that cause decides who pays. River Pools lists its four most common problems as mismatched repairs on colored gelcoats, spider cracks, bulging walls and plumbing leaks from settling (River Pools, updated April 9, 2026). Only one of those, a leak from a manufacturing defect, is a warranty item; the rest trace to installation, backfill or water chemistry.
Color is the hidden cost of any patch. River Pools says metallic and flake finishes are hard to match outside the factory, while solid gelcoats go on in one layer and match more easily, and Latham’s warranty (section 8q) accepts shade variance after its own repairs. Before a patch, ask the repairer to test the color on a hidden spot such as the back of a step.
How do you tell a cosmetic crack from a structural one?
Check two things: depth and water loss. A spider crack stays inside the 27 to 30 mil gelcoat and the water level holds. A structural crack runs through the laminate, and Latham defines structural failure as water loss from a fracture, void or crack caused by a manufacturing defect. If the pool drops faster than evaporation, treat the crack as structural until a leak test says otherwise.

| Defect | Layer it reaches | What you see | Where the repair happens | Source |
|---|---|---|---|---|
| 1 Spider or star crack | Gelcoat only (27 to 30 mils) | Fine web or star lines | Regrind and refill the gelcoat | River Pools; 1st Direct Pools |
| 2 Osmotic blister | Gelcoat and the resin behind it | Raised bubble, dime size or smaller | Grind open, dry, refill; surface warranty claim | River Pools; West System |
| 3 Structural crack | Through the laminate | Water loss | Maker's authorized repair | Latham warranty section 2 |
| 4 Fading, chalking, whitening | Top of the gelcoat | Chalky, faded or white film | Water balance, polish or recoat | River care guide 2026; San Juan; Thursday |
| 5 Wall bulge | Whole wall, from the backfill side | Wall pushed inward | Excavate and regravel behind the shell | River Pools (Jul 2025); Thursday warranty |
Sources: River Pools manufacturing page, River Pools osmotic blisters, Latham warranty section 2, West System (2004), River Pools sand vs gravel (Jul 2025), Thursday warranty. Download CSV
- Mark and measure the water levelPut tape at the waterline and read it after 24 hours with the pump off; compare the drop with your local evaporation rate before blaming the shell.
- Look at where the crack sitsCracks on the beam under the coping are excluded by Latham (section 8p: crazing, spider cracks and chips in the beam are not cause for a claim).
- Watch it for 7 daysA crack that weeps, stains or lengthens, or a water loss that continues with the pump off, needs a leak test before a warranty claim.
- Photograph it with a coin for scaleLatham and River both ask for photos with the claim; date every photo and keep your water test records.
Leak tests on plumbing, skimmers and lights come before a shell claim, since River Pools names plumbing leaks from settling as one of its 4 most common fiberglass problems. The dye and bucket tests are laid out in our pool leak detection guide.
How can I fix cracks in my fiberglass pool?
Grind the crack out to the depth of the gelcoat, tape around it, fill it with matching gelcoat catalyzed at 2% MEKP, then sand and buff. The 1st Direct Pools guide, written for Leisure Pools shells, says the patch hardens in 1 to 3 hours and must pass an acetone rub before water touches it; an uncured patch turns white underwater.
- Keep the water above the skimmerWork only on cracks above the waterline, on steps or benches you can dry with the water at normal level; Latham, River and Thursday void their warranties below the skimmer.
- Grind along the crackUse a die grinder down to the thickness of the original gelcoat, about 27 to 30 mils on a River shell, so the new gelcoat locks into a clean groove.
- Tape and mixMask around the groove to allow for shrinkage. Mix gelcoat with 2% MEKP: 20 ml per litre, or 12 drops per ounce for Evercoat One Step Gel-Kote.
- Fill and screed flatApply with a blade and screed level with the tape. Evercoat gives about 15 minutes of working time at 72 to 75F.
- Let it hardenPull the tape and wait 1 to 3 hours, longer when cool. Cover small chip repairs with clear release film for about 1 hour so the surface cures tack free.
- Sand and buffWet sand at 400 grit until level, then 800 and 1,200 grit; finish with cutting compound. Evercoat’s chip kit instructions stop at 600 grit, compound and wax.
- Check the cureRub with acetone on a white rag. Color on the rag means wait an hour and retest; no cure after 6 hours means grind it out and start again.
| Product or method | Used for | Mix or catalyst | Working, set and fill times | Finish and prep | Source and date |
|---|---|---|---|---|---|
| Pool gelcoat patch (1st Direct Pools guide) | Star cracks | 2% MEKP: 20 ml per litre | Hard in 1 to 3 hours; acetone rub test; regrind if not cured at 6 hours | Wet sand 400, then 800, then 1,200 grit; cutting compound | 1st Direct Pools, 2008 |
| Evercoat One Step Finishing Gel-Kote | Gouges, chips, scratches | 12 drops MEKP per 1 oz | About 15 minutes working time at 72 to 75F | No mold release needed for a full cure | Evercoat training portal, read Nov 2026 |
| Evercoat gelcoat repair kits 100668 and 108000 | Small chips | 4 drops hardener per teaspoon of gel paste | About 15 minutes working; remove film after about 1 hour | Clear release film; 600 grit wet sand; rubbing compound; wax | Evercoat via Wholesale Marine (2009); $76.97 at Fisheries Supply, Nov 2026 |
| J-B Weld WaterWeld epoxy putty | Stopgap leak plug, sets under water | Knead two-part putty | Sets in 15 to 25 minutes, hard in 1 hour | Can be sanded and painted | J-B Weld, read Nov 2026 |
| Insl-X Epoxy Pool Paint IG-40XX | Full repaint | 1:1 by volume; 30 minute induction at 77F | Pot life 6 hours at 77F; fill after 7 days outdoors, 14 indoors; surface 50 to 100F | Scuff sand bare fiberglass with 150 to 180 grit; 350 to 400 sq ft per gallon | Benjamin Moore TDS (2020); product page read Nov 2026 |
| Ramuc EP Hi-Build epoxy | Full repaint | Two parts, mechanically mixed | 3 hour pot life; fill after 5 to 7 days outdoors, 10 to 14 indoors | 150 to 200 sq ft per 2 gal kit bare, 300 to 350 recoat; $257.99 | YourPoolHQ listing, Nov 10, 2026 |
Sources: 1st Direct Pools (2008), Evercoat One Step Gel-Kote, Evercoat kit instructions via Wholesale Marine, Fisheries Supply, J-B Weld WaterWeld, Insl-X IG-40XX TDS, YourPoolHQ Ramuc listing; read November 10, 2026. Download CSV
Can you repair a fiberglass pool without draining it?
Yes for anything above the waterline, and that is the rule, not a shortcut. Latham, River and Thursday void their warranties if the water drops below the skimmer, and San Juan warns the shell may crack or buckle and tells owners not to drain it themselves. Below the waterline, a two-part epoxy putty such as J-B Weld WaterWeld, which sets under water in 15 to 25 minutes, holds as a stopgap.
A drained fiberglass shell is held in place only by its backfill, so groundwater can push it up. That is why Latham’s warranty puts draining, bracing and removing groundwater on the buyer when a covered repair needs an empty pool (section 10), and River Pools prints “Do not drain the pool!” in its owner warranty. Our how to drain a pool guide covers hydrostatic valves and discharge rules for the cases where a pro must do it.
| What a repair guide says | Who says it | What the primary document says | Primary source |
|---|---|---|---|
| Drain the pool to 6 inches below the damaged area | Pool Doctor of the Palm Beaches repair article | Water below the skimmer voids the warranty; San Juan says never drain it yourself | Latham 11a; River Rev0423; Thursday Rev. 10.1.26; San Juan |
| Apply gelcoat in 5 mil coats to 20 to 25 mils | Pool Doctor of the Palm Beaches | Factory gelcoat is sprayed to 27 to 30 mils | River Pools manufacturing page |
| Fiberglass gelcoat can only be applied in a factory | HomeGuide (Apr 2025) | Field gelcoat patches at 2% MEKP are standard for star cracks; whole-shell recoats use paint or polymer | 1st Direct Pools guide (2008) |
| Epoxy paint only bonds to a bare surface | River Pools resurfacing article (2020) | Insl-X and Ramuc both list application over previous epoxy coatings in sound condition | Insl-X TDS; Ramuc listing |
| Keep calcium hardness at 150 to 200 ppm | River Pools owner warranty Rev0423 | River's 2026 care guide says under 120 ppm; Latham asks for 250 to 350 ppm | River care guide 2026; Latham CWP107.26 |
Sources: Pool Doctor of the Palm Beaches, HomeGuide, River Pools (2020), Latham, River Pools Rev0423, Thursday, San Juan, River Pools manufacturing, 1st Direct Pools, Insl-X TDS, Ramuc listing, River care guide 2026. Download CSV
The calcium row matters for repairs, because the wrong water undoes a new patch or paint job. River Pools’ 2026 care guide asks for calcium under 120 ppm and pH 7.2 to 7.4, its older Rev0423 warranty lists 150 to 200 ppm, and Latham asks for 250 to 350 ppm, so follow the current document from your own maker. Target ranges for every reading are in our pool chemical levels chart.
What should you do about fiberglass pool blisters?
File a surface warranty claim before anyone grinds them. Osmotic blisters are raised bubbles, usually dime size or smaller, that form when water passes the gelcoat and reacts with polyester resin behind it. Latham covers them for the original buyer for life, River and Thursday for 15 years; San Juan’s structural warranty excludes gelcoat bubbling.
River Pools says blisters were common before vinyl ester resin became standard and are now “all but extinct in new pools”, which it credits to a vinyl ester layer of about 100 to 120 mils (River Pools). West System, a marine epoxy maker, explains the chemistry in its 2004 repair manual: water reaching unreacted resin forms an acidic solution that breaks ester links, and warmer water speeds it up (West System).

Out of warranty, the West System boat method shows why a full repair is a pro job: abrade with 80 grit, grind or peel the gelcoat off, dry the laminate while monitoring moisture readings, keep the surface temperature under 50C, then rebuild with epoxy and fairing. For a pool, that work happens in an empty shell, so it is usually priced as resurfacing at $7,000 to $15,000 (HomeGuide, April 2025).
Why is my fiberglass pool fading, chalky or white?
Most often the water. River Pools’ 2026 care guide says calcium combined with high pH and chlorine causes most discoloration, and tells owners to correct pH before 7.6 because damage past that point is permanent and not covered. Thursday Pools warns that salt systems greatly raise the risk of whitening when chemistry drifts, and whitening is excluded from its warranty.
- Chalky film that wipes off: check calcium and pH first; River’s 2026 guide recommends a chelating stain and scale product when calcium is above 120 ppm.
- Even dulling from sun: San Juan says uniform dulling of its Iridium finish can be re-polished with a professional boat polish.
- Faded paint on a previously painted shell: Insl-X states that its epoxy pool coating, like any epoxy, will chalk and fade over time under ultraviolet light.
- Spots of color: metals or organics, treated in the water; see our pool stains guide for the ascorbic acid test and doses.
San Juan is the one maker here with a finish-color promise: its surface warranty covers staining, discoloration and excessive fading from defects for 10 years, but not gradual change from chemicals or weather, and it needs notice within 5 days of discovery by registered mail. Latham’s section 8j excludes fading, staining and discoloration outright.
How do you fix a bulging fiberglass pool wall?
From the outside. River Pools traced its own bulges to sand backfill: saturated sand liquefies and, being heavier than the water inside, pushes the wall in. The fix is to excavate behind the wall with the pool full, brace it, and refill with clean crushed stone, 3/4 in or smaller per River, or 3/8 in to 1 1/2 in washed chip stone per Thursday’s warranty.
- Keep the pool fullThe water inside is what holds the wall’s shape; lowering it to inspect the bulge adds load and voids the Latham, River and Thursday warranties.
- Check the drainage firstThursday requires an 8 in perforated well pipe set 12 in below the deep end on 2 in of gravel; if it is missing or clogged, groundwater will refill the backfill.
- Excavate behind the bulgeThe installer removes the saturated backfill along the affected wall, down past the bulge.
- Brace and refillPush the wall back to line and refill with crushed stone, which River says performs the same wet or dry; Thursday’s warranty has backfill placed, alternating, to within 12 in of the water level.
- Replace the deck sectionDeck or coping removed for access is outside every warranty here; price it in the same bid.
We found no published price for bulge repair, and forum figures are not a source. Ask for a written bid that names the backfill material and size (River: crushed stone 3/4 in or smaller; Thursday: 3/8 in to 1 1/2 in washed chip stone), the well pit depth and whether deck and coping replacement are included, then compare it with the shell’s warranty status before you sign.
Get quotes for fiberglass pool repair
How much does it cost to fix a fiberglass pool?
A spot gelcoat repair costs $300 to $400 from a pro (Angi, July 2026) or $76.97 for a DIY kit (Fisheries Supply, November 2026). Out-of-warranty structural crack and leak repairs run $1,000 to $5,000 (American Fiberglass Pools, 2025). A whole-shell resurface ranges from about $1,500 for pro epoxy paint to $10,000 to $13,000 for a polymer coating (River Pools).
Structural figures are out-of-warranty prices; a covered defect is repaired by the maker.
Source: Fisheries Supply (Nov 10, 2026), Angi (updated Jul 9, 2026), American Fiberglass Pools (Mar 8, 2025). Download chart data (CSV)
| Job | Price | Who published it | Date |
|---|---|---|---|
| Gelcoat repair kit, DIY (Evercoat 108000) | $76.97 | Fisheries Supply (retailer) | Nov 10, 2026 |
| Pro gel coat repair of dings, scratches, cracks | $300 to $400 | Angi | Updated Jul 9, 2026 |
| Repaint after a gel coat repair | About $800 more | Angi | Updated Jul 9, 2026 |
| Pool repair labor | $45 to $65 per hour | Angi | Updated Jul 9, 2026 |
| Structural repairs (cracks, leaks) | $1,000 to $5,000 | American Fiberglass Pools (contractor) | Mar 8, 2025 |
| Water refill and chemicals after a repair | $300 to $700 | American Fiberglass Pools | Mar 8, 2025 |
| San Juan warranty service visit | $75 trip charge per visit | San Juan Pools warranty | Current page |
Sources: Fisheries Supply, Angi (Wayback capture, Aug 2026), American Fiberglass Pools, San Juan Pools. Download CSV
Each publisher prices a different pool and scope; none states a sample size.
Source: River Pools (2020), American Fiberglass Pools (Mar 2025), Angi (Jul 2026), HomeGuide (Apr 2025); read November 2026. Download chart data (CSV)
| Option | Published price | Life or wait claimed | Who published it | Date |
|---|---|---|---|---|
| Epoxy pool paint, pro | About $1,500 | Up to 5 years; pool usable after up to 2 weeks | River Pools | Mar 25, 2020 |
| Epoxy pool paint, DIY materials | $257.99 per 2 gal Ramuc kit | Up to eight or more years (seller claim); fill after 5 to 7 days | YourPoolHQ | Nov 10, 2026 |
| DIY resurfacing, all in | $1,500 to $4,000 | 3 to 5 days of labor | American Fiberglass Pools | Mar 8, 2025 |
| Basic gel coat resurfacing, pro | $5,000 to $8,000 | Not stated | American Fiberglass Pools | Mar 8, 2025 |
| Full resurfacing, pro | About $6,500 | Not stated | Angi | Jul 9, 2026 |
| Epoxy or polymer coating, pro | $7,000 to $12,000 | Not stated | American Fiberglass Pools | Mar 8, 2025 |
| Fiberglass resurfacing, pro | $7,000 to $15,000 | Not stated | HomeGuide | Apr 25, 2025 |
| ecoFINISH thermoplastic polymer, pro | $10,000 to $13,000 minimum | Refill right away | River Pools | Mar 25, 2020 |
Sources: River Pools (Mar 25, 2020), YourPoolHQ, American Fiberglass Pools, Angi, HomeGuide. Download CSV
The spread is wider than the jobs. River Pools prices pro epoxy paint at about $1,500 while American Fiberglass Pools puts epoxy or polymer at $7,000 to $12,000, and Angi adds about $800 to repaint after a spot repair. None states a pool size or sample. Ask each bidder for square footage, number of coats and the product data sheet.
| Line | Input or result | How it is worked out |
|---|---|---|
| Pool size (example) | 14 x 28 ft, 4.5 ft average depth | PC&S example, not a model |
| Floor area | 392 sq ft | 14 x 28 |
| Wall area | 378 sq ft | 2 x (14 + 28) x 4.5 |
| Surface to coat | 770 sq ft | 392 + 378; steps and curves ignored |
| Coat 1 at the bare rate (150 to 200 sq ft per kit) | 4 to 6 kits | 770 / 200 = 3.9; 770 / 150 = 5.1; rounded up |
| Coat 2 at the recoat rate (300 to 350 sq ft per kit) | 3 kits | 770 / 350 = 2.2; 770 / 300 = 2.6; rounded up |
| Kits for two coats | 7 to 9 kits | 4 + 3 to 6 + 3 |
| Paint cost at $257.99 per kit | $1,805.93 to $2,321.91 | 7 x 257.99 to 9 x 257.99 |
| Compare: pro epoxy paint (River Pools, 2020) | About $1,500 | Published figure |
| Compare: pro polymer coating (River Pools) | $10,000 to $13,000 | Published minimum |
Sources: coverage and price from the Ramuc EP Hi-Build listing at YourPoolHQ (Nov 10, 2026); pro figures from River Pools. PC&S arithmetic; the listing does not state a coat count. Download CSV
Paint is not a gelcoat: a painted fiberglass pool becomes a painted pool, with Insl-X calling for a scuff sand at 150 to 180 grit, 7 days before filling and stripping once 4 or more aged layers build up. New shell prices for a replacement, if repair stops making sense, are in our fiberglass pool cost guide, and finishes for concrete pools are compared in pool resurfacing cost.
Does a repair void your fiberglass pool warranty?
It can. Latham does not cover repairs by anyone other than its authorized representative or an approved contractor (section 8h), River excludes repairs by anyone but its own authorized representative, and San Juan withdraws coverage entirely if anyone else repairs the shell. Report the defect in writing first, then wait for the maker to name the repairer.
| Maker | Notice deadline and method | What to send | Who pays to drain and refill | Repairs by others |
|---|---|---|---|---|
| Latham (and Narellan) | Written notice within 10 days of discovery; 5 days for transport damage; email or online claim form | Name and contact, serial number (on the second step), install date and builder, description and photos | Buyer drains, braces and removes groundwater (section 10); no refill compensation (8r) | Not covered unless by an authorized representative or approved contractor (8h) |
| River Pools | In writing within 30 days of the defect | Dated proof of purchase, photos, a regularly updated operation and service record | Buyer empties and refills; pool must be empty for service | Excluded unless by an authorized River representative |
| Thursday Pools | In writing within 30 days of identifying the defect | Dated proof of purchase, operation and service records, photos if inspection is requested | Thursday not liable for refill water and chemicals | Damage caused by third parties voids coverage |
| San Juan Pools | Registered mail within 15 days; surface claims within 5 days | Get the authorized repairer's name in writing before any repair | Not responsible for water or chemicals; $75 trip charge per visit | No warranty if anyone other than the manufacturer repairs the shell |
Sources: Latham CWP107.26 rev. 4/26 sections 6, 8, 10; River Pools Rev0423; Thursday Pools Rev. 10.1.26; San Juan warranty page; read November 2026. Download CSV
Cosmetic patches above the waterline are the gray zone: the cracks themselves are excluded, so a careful owner repair rarely affects a claim, but a botched grind into the laminate can. Coverage terms, transfer rules and lifespans by maker are compared in our fiberglass pool guide. None of the 83 US pool product recalls in our pool product recalls registry involves a fiberglass shell.
Which fiberglass pool repair fits your situation?
Match the symptom to the row. Cosmetic cracks and chips are owner repairs; leaks and blisters go to the maker in writing within its deadline; chalking starts with water chemistry; a bulge is an excavation job with the pool kept full. Anything that needs the water below the skimmer waits for the maker’s written approval.
| If your situation is | Do this | Why (source) |
|---|---|---|
| Fine web or star cracks above the waterline, no water loss | Patch the gelcoat yourself or hire a $300 to $400 repair; or leave it | Cosmetic; excluded from Latham, River and Thursday warranties |
| Pool loses more water than evaporation and you can see a crack | Photograph it and send written notice to the maker before anyone repairs it | Latham 10 days, River and Thursday 30 days, San Juan 15 days by registered mail |
| Raised bubbles, dime size or smaller | File a surface warranty claim; do not grind them open first | Latham lifetime (original buyer); River and Thursday 15 years |
| Surface chalky, faded or white but smooth | Bring pH to 7.2 to 7.4 and calcium under 120 ppm; polish | River 2026 care guide; San Juan allows a professional boat polish |
| Surface rough, peeling or repainted 4 or more times | Resurface: epoxy paint about $1,500 pro, polymer $10,000 to $13,000 | River Pools; Insl-X says 4 or more aged layers may need stripping |
| Wall bowed inward | Call the installer to excavate and regravel; never lower the water to look | River Pools (Jul 2025); Thursday backfill spec |
| Repair would need the water below the skimmer | Get the maker's written approval and a braced, dewatered drain plan first | Latham, River and Thursday void the warranty below the skimmer |
Sources: Latham, River Pools, Thursday Pools, San Juan, River care guide 2026, River Pools (Jul 2025), Insl-X TDS, Angi. Download CSV

Pump, heater and plumbing faults that look like shell problems are triaged in our pool repair guide, with labor rates for each trade.
How we compiled this
We read four fiberglass maker warranties (Latham, River Pools, Thursday Pools, San Juan), River Pools’ 2026 care guide and four of its technical articles, one pool gelcoat repair guide, two gelcoat product instructions, two epoxy pool paint data sheets or listings and five dated price pages, all in November 2026. We did not test products or inspect pools. Forum threads were used only for question wording.
Frequently Asked Questions
Can a fiberglass pool be repaired?
Yes. Spider cracks, chips and fading are field repairs with gelcoat or paint, and leaking cracks and osmotic blisters are warranty repairs when the defect came from manufacturing. Latham, River and San Juan restrict who may repair the shell, so send written notice to the maker before any structural work, and keep the water above the skimmer.
How much does it cost to fix a fiberglass pool?
Angi puts a gel coat repair of dings, scratches and cracks at $300 to $400, updated July 2026, and a DIY Evercoat kit sold for $76.97 at Fisheries Supply on November 10, 2026. Out-of-warranty structural crack or leak repairs run $1,000 to $5,000 (American Fiberglass Pools, 2025); resurfacing runs $7,000 to $15,000 (HomeGuide).
How can I fix cracks in my fiberglass pool?
Grind the crack to the depth of the gelcoat, tape around it, fill with matching gelcoat mixed at 2% MEKP, about 20 ml per litre, and let it harden 1 to 3 hours. Wet sand at 400, 800 and 1,200 grit, buff, then pass an acetone rub test before the water touches it, per the 1st Direct Pools guide.
Will new fiberglass stick to old fiberglass?
Only to a clean, abraded surface. The 1st Direct Pools guide grinds a groove into old gelcoat before new gelcoat goes in, West System abrades with 80 grit before rebuilding, and Insl-X requires a 150 to 180 grit scuff sand on fiberglass before its epoxy paint. Paint or gelcoat over a glossy or chalky surface will not hold.
How long after a gelcoat repair can you swim?
Once the patch passes the acetone rub test: the 1st Direct Pools guide says gelcoat hardens in 1 to 3 hours, and a repair not cured after 6 hours must be ground out. Painted repairs take longer: Insl-X asks for 7 days before filling outdoors and 14 days indoors, and Ramuc lists 5 to 7 days outdoors.
Should I drain my fiberglass pool to fix a crack?
No. Latham, River Pools and Thursday Pools each void their warranties if the water falls below the skimmer, and San Juan warns the shell may crack or buckle if drained by anyone not authorized. Repair cracks above the waterline in place, use an underwater epoxy putty as a stopgap, and leave draining to the maker’s approved repairer.
Sources
- Latham Pool Products. Latham Fiberglass Pools Limited Lifetime Warranty (CWP107.26, rev. 4/26). Accessed 2026-11-08.
- River Pools. One-Time Transferable Limited Structural Warranty and 15-Year Surface Warranty (Rev0423). Accessed 2026-11-08.
- Thursday Pools. One-Time Transferable Limited 35 Year Structural Warranty (Rev. 10.1.26). Accessed 2026-11-08.
- San Juan Pools. Warranty. Accessed 2026-11-08.
- River Pools. Fiberglass Pool Care Guide (2026 update). Accessed 2026-11-10.
- River Pools. Top 4 Fiberglass Pool Problems and Solutions (updated April 9, 2026). Accessed 2026-11-08.
- River Pools. What Causes Osmotic Blisters on Fiberglass Pools. Accessed 2026-11-08.
- River Pools. Manufacturing: gel coat surface layer. Accessed 2026-11-10.
- River Pools. Fiberglass Pool Gel Coat Problems and Manufacturing Solutions (2011). Accessed 2026-11-10.
- River Pools. Installing a Fiberglass Pool on Sand vs Gravel (July 3, 2025). Accessed 2026-11-10.
- River Pools. How Much Does Inground Pool Resurfacing Cost? (March 25, 2020). Accessed 2026-11-10.
- West System. Gelcoat Blisters: A Guide to Osmosis Repair (5th ed., 2004). Accessed 2026-11-08.
- 1st Direct Pools. Repairing a Fibreglass Pool (2008). Accessed 2026-11-10.
- Evercoat. One Step Finishing Gel-Kote. Accessed 2026-11-10.
- Wholesale Marine. Instructions and Color Chart for Evercoat Gel Coat Repair (Evercoat text, 2009). Accessed 2026-11-10.
- Fisheries Supply. Evercoat 108000 gelcoat repair kit listing. Accessed 2026-11-10.
- J-B Weld. WaterWeld Epoxy Putty. Accessed 2026-11-10.
- Benjamin Moore. Insl-X Epoxy Pool Paint IG-40XX technical data sheet (2020). Accessed 2026-11-10.
- Benjamin Moore. Insl-X Epoxy Pool Paint product page. Accessed 2026-11-10.
- YourPoolHQ. Ramuc EP Hi-Build Epoxy Swimming Pool Paint, 2 gallon kit. Accessed 2026-11-10.
- Angi. How Much Do Swimming Pool Repairs Cost? (updated July 9, 2026; Wayback capture). Accessed 2026-11-10.
- American Fiberglass Pools. Fiberglass Pool Resurfacing Cost Guide (March 8, 2025). Accessed 2026-11-10.
- HomeGuide. How Much Does Pool Resurfacing Cost? (April 25, 2025). Accessed 2026-10-08.
- Pool Doctor of the Palm Beaches. Repair Your Damaged Fiberglass Pool. Accessed 2026-11-10.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.