
Pool Algaecide: Which Type to Use, EPA Label Doses and How to Use It
Pool algaecide is an EPA-registered chemical that kills or prevents algae alongside chlorine: polyquat 60 labels use 11 to 18 fl oz per 10,000 gallons for visible algae, then 2 to 4 fl oz every 5 to 7 days.
- ✓175 registrations counted65 simple quats, 50 polyquats and 36 copper products lead EPA's active pool algaecide list, by PC&S's November 2026 count.
- ✓13 labels, one tableDose, maintenance, key restriction and swim rule for each product type, with the EPA Reg. No. and label file.
- ✓Copper math shownA 4 oz Swimtrine dose adds about 0.27 ppm copper per 10,000 gallons; Leslie's says staining may start above 0.6 ppm.
Key takeaways
- Of 175 active EPA registrations named algaecide or algicide with a swimming pool use site, 65 are simple quats, 50 are polyquats and 36 are copper-only, by PC&S’s count of the EPA Pesticide Product and Label System on November 1, 2026.
- The 2024 Model Aquatic Health Code Annex says simple quats tend to foam when overdosed, polyquats do not foam even at the maximum label dose, and copper products can stain when pH is not controlled.
- Label swim waits run from none on Swimtrine (EPA Reg. No. 8959-2) to 15 minutes on BioGuard Algae Complete (5185-513) to 6 hours of filtration with swimmers out on Clor Mor Maintenance Algaecide (69681-20).
- A 4 oz opening dose of Swimtrine adds about 0.27 ppm of copper to 10,000 gallons by PC&S arithmetic; if no copper leaves, the label program passes Leslie’s 0.6 ppm staining line at week 6 and EPA’s 1.0 mg/L secondary standard at week 12.
- Algaecide supplements chlorine: HASA, which makes both, says a pool with enough free chlorine for its CYA level may not need a routine algaecide, and the HTH Algae Stop label (1258-1288) says pools with heavy algae growth must be cleaned before use.
- EPA reviews an algaecide’s toxicology but not its efficacy at registration; California requires efficacy studies, according to the MAHC Annex.
What is pool algaecide, and does your pool need it?
Pool algaecide is an EPA-registered pesticide that kills or prevents algae and works alongside chlorine, not instead of it. HASA says a pool that holds enough free chlorine for its cyanuric acid level, above CDC’s 1 ppm floor (2 ppm with CYA), may not need a routine dose. Algaecide earns its place with chlorine-tolerant mustard or black algae, shady or warm pools that keep relapsing, vacations and winter closing.
Chlorine is itself an algaecide. The 2024 MAHC Annex notes that chlorine and bromine can be registered and used as algaecides, and that most algaecides work when applied at label directions together with frequent, thorough brushing. HASA puts the order plainly: algaecides are supplemental, and the common mistake is pouring one into a pool already taken over by algae and expecting it to clear the water.
Registration is not a performance test. Section 5.7.4.4.4 of the MAHC Annex says EPA does not consider pool algae a public health threat, so it reviews toxicology but does not require an efficacy package; California requires efficacy studies before products are sold there. Every legal product carries an EPA Reg. No., and you can look it up in EPA’s Pesticide Product and Label System to read the accepted label.
What types of pool algaecide are there?
Four families cover almost every product: simple quats (65 of 175 active pool registrations named algaecide), polyquats (50), copper compounds (36 alone, 8 more in blends) and a few chlorine, bromide and silver products. The type decides the side effect: quats can foam, copper can stain, polyquats do neither, and sodium bromide is banned from outdoor pools.
| Type | Active ingredient on the label | Active pool registrations (of 175) | Foams? | Stains? | Example EPA Reg. Nos. |
|---|---|---|---|---|---|
| Quat | Alkyl dimethyl benzyl ammonium chloride (ADBAC) or DDAC | 65 | Yes, when overdosed | No | 1258-1077 HTH Algaecide; 69681-20 Clor Mor Maintenance |
| Polyquat | Poly[oxyethylene(dimethyliminio)ethylene(dimethyliminio)ethylene dichloride] | 50 | No, even at maximum dose | No | 1258-1080 HTH Non-Foaming 60; 7616-73 Kem Tek; 57787-2 Combat 30 |
| Copper | Copper triethanolamine or ethanolamine complex, or copper sulfate | 36 | No | Yes, if misused or pH is off | 8959-2 Swimtrine; 3525-141 Pool Trol; 45729-5 SeaKlear 90-Day |
| Chlorine | Trichlor, dichlor, calcium or sodium hypochlorite | 9 | No | Bleaching if granules sit on vinyl | 42177-67 Olympic Granular Algae-Out |
| Quat + copper | Copper complex plus ADBAC | 5 | Low quat share | Yes | 5185-382 BioGuard MSA II; 8959-14 Black Algaetrine |
| Sodium bromide | Sodium bromide | 5 | No | No | 8959-52 Yellowtrine (indoor pools only) |
| Polyquat + copper | Copper plus polyquat | 2 | No | Full strength stains porous surfaces | 5185-513 BioGuard Algae Complete; 57787-25 Combat Extra |
| Bromine (BCDMH) | Bromochlorodimethylhydantoin | 1 | No | No | 5185-420 BioGuard Master BCDMH |
| Silver | Nanosilver | 1 | No | Concentrate can stain | 68161-1 Algaedyn |
| Copper + chlorine | Copper sulfate plus dichlor | 1 | No | Yes | 7364-46 Tabex Algae Out |
| Total | 175 | Names containing 'algaecide' or 'algicide', status active, swimming pool use site |
Sources: EPA PPLS search ALGAECIDE and ALGICIDE, 223 registration records read November 1, 2026, classified by PC&S; foam and stain columns from the 2024 MAHC Annex 5.7.4.4.4 and the EPA labels named. Download CSV
Source: U.S. EPA Pesticide Product and Label System, product name searches ALGAECIDE and ALGICIDE; classified by PC&S. Download chart data (CSV)
Method: we pulled every product name containing ‘algaecide’ or ‘algicide’ from EPA’s label system, kept the 1,427 active names, reduced them to 223 base registrations and kept the 175 whose record lists a swimming pool use site. Products named otherwise, such as some ‘algae killer’ brands, are not in the count, and store brands sold under a distributor number count once under the base registration.
The chemistry names are long, so read the active ingredient line. Polyquat appears as poly[oxyethylene(dimethyliminio)ethylene(dimethyliminio)ethylene dichloride], and EPA’s 2025 and 2026 label amendments call it polixetonium chloride. Simple quats appear as alkyl dimethyl benzyl ammonium chloride. Copper appears as a triethanolamine or ethanolamine complex, or as copper sulfate pentahydrate.
What do EPA algaecide labels say about dose, stains and swimming?
The labels differ more than the bottles suggest. Visible-algae doses per 10,000 gallons run from 4 oz of a copper product to 36 fl oz of a 30% polyquat, maintenance from 1.3 fl oz every 3 to 5 days to 16 fl oz every three months, and swim waits from none to 6 hours. The table lists 13 current labels by type.
| Product type | Product | EPA Reg. No. | Active ingredient | Visible algae or opening dose per 10,000 gal | Maintenance dose per 10,000 gal | Key label restriction | Swim again | Label file | Label URL |
|---|---|---|---|---|---|---|---|---|---|
| Quat 10% | HTH Algaecide | 1258-1077 | ADBAC 9.96% + 0.04% | 26 fl oz | 6.4 fl oz every 3 to 5 days | Vacuum after 24 hours; maintenance more often in heat or heavy use | Spa use: 15 minutes; pool claim 'immediately swim ready' is optional label text | Jan 14, 2021 | https://www3.epa.gov/pesticides/chem_search/ppls/001258-01077-20210114.pdf |
| Quat 30% | HTH Algae Stop | 1258-1288 | ADBAC 15% + ethylbenzyl ADBAC 15% | 8 fl oz | 2 fl oz every 3 to 5 days | Pools with heavy algae must be cleaned first; pump on for several hours | 15 minutes | Jun 21, 2022 | https://www3.epa.gov/pesticides/chem_search/ppls/001258-01288-20220621.pdf |
| Quat 50% | Clor Mor Maintenance Algaecide | 69681-20 | ADBAC 49.8% + 0.2% | 5.2 fl oz (26 oz per 50,000 gal) | 1.3 fl oz every 3 to 5 days (6.5 oz per 50,000) | Free chlorine 1 to 3 ppm first; not with concentrated chlorine | After at least 6 hours of filtration | Dec 22, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/069681-00020-20251222.pdf |
| Polyquat 60% | HTH Non-Foaming Algaecide 60 | 1258-1080 | Polyquat 60% | 11 to 17 fl oz | 2 to 4 fl oz every 5 to 7 days | Remove settled algae debris by cleaning | Optional claim: 'Swim Immediately' | Sep 16, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/001258-01080-20250916.pdf |
| Polyquat 60% | Kem Tek Algaecide | 7616-73 | Polyquat 60% | 16 oz after shocking to 5 ppm | 2 to 4 oz weekly | Wear waterproof gloves; keep pH 7.2 to 7.6 | 15 minutes, only at 3 ppm chlorine or less | May 20, 2026 | https://www3.epa.gov/pesticides/chem_search/ppls/007616-00073-20260520.pdf |
| Polyquat 30% | Combat 30 | 57787-2 | Polyquat 30% | 24 to 36 fl oz | 4 to 9 fl oz every 5 to 7 days | Do not mix with concentrated chlorine | Not stated | Jan 21, 2026 | https://www3.epa.gov/pesticides/chem_search/ppls/057787-00002-20260121.pdf |
| Copper | Swimtrine Algaecide | 8959-2 | Copper ethanolamine complex (7.41% copper) | 4 oz | 2 oz every 2 weeks | Do not exceed label dosing; 0.72 lb copper per gallon | Immediately, no waiting | Apr 14, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/008959-00002-20250414.pdf |
| Copper | Pool Trol Copper Algaecide | 3525-141 | Copper triethanolamine complex 23.5% (7.1% copper) | 4 oz (2 oz per 5,000 gal) | 2 oz (1 oz per 5,000 gal) | Do not mix with other chemicals; 0.76 lb copper per gallon | Immediately, no waiting | Jul 7, 2026 | https://www3.epa.gov/pesticides/chem_search/ppls/003525-00141-20260707.pdf |
| Copper | SeaKlear 90-Day Algae Prevention and Remover | 45729-5 | Copper sulfate pentahydrate 11.8% (3.0% copper) | 32 fl oz for severe algae | 16 fl oz every 3 months | pH 7.2 to 7.8, alkalinity 80 to 120 ppm; use with an EPA-registered sanitizer | Not stated | Aug 26, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/045729-00005-20250826.pdf |
| Copper | Algae Kil CB 7 | 57787-17 | Copper triethanolamine complex 23.4% (7% copper) | 4 fl oz light, 10 fl oz heavy | 2 to 5 oz every other week | pH 7.2 to 7.6; never mix products in one pail | Immediately, once chlorine is 4 ppm or less | Mar 28, 2024 | https://www3.epa.gov/pesticides/chem_search/ppls/057787-00017-20240328.pdf |
| Copper + polyquat | BioGuard Algae Complete | 5185-513 | Copper sulfate pentahydrate 13.07% + polyquat 6.5% | 16 fl oz, 1 hour after a shock | 1.5 fl oz weekly | Test for metals first; not for biguanide or peroxide pools; full strength stains porous surfaces | Prevention: 15 minutes; treatment: chlorine 1 to 4 ppm | Jul 16, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/005185-00513-20250716.pdf |
| Copper + quat | BioGuard MSA Algaecide II | 5185-382 | Copper triethanolamine 23.6% + ADBAC 2.5% | 8 fl oz, diluted | 2 fl oz every 2 weeks | Stain and scale control 2 days after the final treatment | 15 minutes after a preventive dose | Aug 6, 2026 | https://www3.epa.gov/pesticides/chem_search/ppls/005185-00382-20260806.pdf |
| Sodium bromide | Yellowtrine | 8959-52 | Sodium bromide 98% | 4 oz, then 1 lb dry chlorine | 4 oz weekly above 80 F; 2 oz below | Not for use in outdoor pools | A few hours after treatment | Apr 15, 2025 | https://www3.epa.gov/pesticides/chem_search/ppls/008959-00052-20250415.pdf |
Sources: EPA-accepted labels on the EPA Pesticide Product and Label System: 1258-1077, 1258-1288, 69681-20, 1258-1080, 7616-73, 57787-2, 8959-2, 3525-141, 45729-5, 57787-17, 5185-513, 5185-382, 8959-52. Doses printed per 5,000 or 50,000 gallons were scaled by PC&S. Download CSV
Three patterns stand out. Strength drives volume: Combat 30 at 30% polyquat calls for 24 to 36 fl oz where HTH Non-Foaming 60 calls for 11 to 17. Copper products are dosed in ounces, not cups, because a gallon of Swimtrine holds 0.72 lb of elemental copper. And several ‘swim immediately’ lines are optional marketing text in brackets on the master label, so the retail bottle may print a stricter rule; the bottle you buy wins.
Mustard and black algae have their own labeled products and doses, such as Black Algaetrine (8959-14) at 12 oz per 10,000 gallons, listed in our mustard algae guide and our black algae treatment guide. The chlorine doses EPA labels set for green water are in our guide on how to clear a green pool. Which algae you have, and how long each type takes to clear, is covered in our guide on how to get rid of algae in a pool.
How much algaecide should you add for your pool size?
Multiply the label’s per-10,000-gallon dose by your gallons divided by 10,000. A 20,000 gallon pool with visible algae takes 22 to 34 fl oz of HTH Non-Foaming 60 or 48 to 72 fl oz of Combat 30, then 4 to 8 or 8 to 18 fl oz per maintenance dose. At Leslie’s $37.99 quart price, a 16-week season of weekly polyquat maintenance costs $75.98 to $151.96.
| Product and dose | 10,000 gal | 15,000 gal | 20,000 gal | 30,000 gal | Unit |
|---|---|---|---|---|---|
| HTH Non-Foaming 60 (polyquat 60%), visible algae | 11 to 17 | 16.5 to 25.5 | 22 to 34 | 33 to 51 | fl oz |
| HTH Non-Foaming 60, maintenance every 5 to 7 days | 2 to 4 | 3 to 6 | 4 to 8 | 6 to 12 | fl oz |
| Combat 30 (polyquat 30%), visible algae | 24 to 36 | 36 to 54 | 48 to 72 | 72 to 108 | fl oz |
| Combat 30, maintenance every 5 to 7 days | 4 to 9 | 6 to 13.5 | 8 to 18 | 12 to 27 | fl oz |
| HTH Algaecide (quat 10%), initial | 26 | 39 | 52 | 78 | fl oz |
| HTH Algaecide, maintenance every 3 to 5 days | 6.4 | 9.6 | 12.8 | 19.2 | fl oz |
| Swimtrine (copper), opening | 4 | 6 | 8 | 12 | fl oz |
| Swimtrine, every 2 weeks | 2 | 3 | 4 | 6 | fl oz |
| BioGuard Algae Complete, visible algae after shock | 16 | 24 | 32 | 48 | fl oz |
| BioGuard Algae Complete, weekly | 1.5 | 2.25 | 3 | 4.5 | fl oz |
Sources: EPA labels 1258-1080, 57787-2, 1258-1077, 8959-2, 5185-513. Columns other than 10,000 gallons are scaled by PC&S. Download CSV
| Step | Input | Calculation | Result |
|---|---|---|---|
| Product | Leslie's Algae Control, 60% polyquat, 1 qt (32 fl oz) at $37.99 (Wayback capture, Sept 16, 2026) | 37.99 / 32 | $1.19 per fl oz |
| Visible algae, 20,000 gal | Label: 11 to 16 fl oz per 10,000 gal | 22 to 32 fl oz x $1.19 | $26.12 to $37.99 |
| One maintenance dose, 20,000 gal | Label: 2 to 4 fl oz per 10,000 gal every 5 to 7 days | 4 to 8 fl oz x $1.19 | $4.75 to $9.50 |
| Swim season | Median 114 days of 80 F highs across 60 metros (NOAA 1991 to 2020 normals) | 114 / 7 = 16.3; use 16 weekly doses | 16 doses |
| Season of maintenance | 16 doses | 16 x $4.75 to 16 x $9.50 | $75.98 to $151.96 |
Sources: Leslie’s Algae Control 1 qt, Wayback capture September 16, 2026; PC&S pool season length index (NOAA 1991 to 2020 normals). Arithmetic by PC&S. Download CSV
The quart price comes from our pool equipment and chemical price index, which tracked the same $37.99 Leslie’s quart listing in captures from May 2024 to September 2026. The 16 weeks come from our swim season index, where the median of 60 metros has 114 days a year with normal highs of 80 F or more; Sun Belt pools run longer seasons and more doses.
How to use algaecide in a pool, step by step
Balance the water, brush, shock first if algae is visible, then add the algaecide with the pump running and keep it running 24 hours. Brush the next day, vacuum, repeat if the label allows, then switch to the maintenance dose. Each step below carries the figure from the label behind it.
- Test and balanceSet pH to 7.2 to 7.6 (Algae Complete, Kem Tek) and free chlorine to your normal range; Clor Mor’s quat label wants 1 to 3 ppm before dosing.
- Check metals before copperThe Algae Complete label says test for metals first. Above 0.6 ppm copper, Leslie’s warns staining may occur; pick a polyquat instead.
- Brush and vacuumLabels start with cleaning: HTH Non-Foaming 60 says remove settled algae debris, and HTH Algae Stop says pools with heavy growth must be cleaned before use.
- Shock first if algae is visibleAlgae Complete: add a shock, circulate 1 hour, then the algaecide. Kem Tek: shock to 5 ppm, then 16 oz per 10,000 gallons.
- Dose with the pump runningPour the measured dose where growth is heaviest or around the edge, never premixed with chlorine. Pro Algaecide bars mixing with concentrated chlorine.
- Circulate 24 hoursAlgae Complete asks for continuous circulation for 24 hours; Clor Mor for at least 6 hours with no swimmers.
- Brush, vacuum and repeat if neededBrush the next day and vacuum dead algae after 24 hours. Algae Complete repeats after 2 to 4 days; MSA II adds a stain and scale control 2 days after the last dose.
- Switch to maintenancePolyquat 60%: 2 to 4 fl oz per 10,000 gallons every 5 to 7 days. Algae Complete: 1.5 fl oz weekly. Swimtrine: 2 oz every 2 weeks.
| What a guide says | What the label or primary source says | Sources |
|---|---|---|
| Simplified Pools: add algaecide 24 to 48 hours after shocking, once chlorine is back to 2 to 5 ppm | BioGuard Algae Complete label: shock, circulate 1 hour, then add 16 fl oz; Kem Tek label: shock to 5 ppm, then the 16 oz algaecide dose | Simplified Pools; EPA labels 5185-513 and 7616-73 |
| Poolonomics: wait 10 to 15 minutes before swimming; Hunker: about 30 minutes | Labels run from no wait (Swimtrine) to 15 minutes (Algae Complete) to 6 hours of filtration (Clor Mor Maintenance) | Poolonomics; Hunker; EPA labels 8959-2, 5185-513, 69681-20 |
| Beatbot: the typical dose is 1 to 4 oz per 10,000 gallons | Label doses per 10,000 gal run from 1.3 fl oz (Clor Mor maintenance) to 36 fl oz (Combat 30, visible algae) | Beatbot; EPA labels 69681-20 and 57787-2 |
| Pool Research: most algaecides on the market have a copper base | 44 of 175 active pool registrations named algaecide or algicide contain copper; 115 are quats or polyquats | Pool Research; EPA PPLS count by PC&S |
| HTH Algae Guard Advanced page: chlorine above 5 ppm can deactivate algaecide; wait 24 hours after shocking | HASA: high chlorine can oxidize polyquat; the Algae Complete label still doses 1 hour after a shock | HTH; HASA; EPA label 5185-513 |
Sources: Simplified Pools; Poolonomics; Hunker; Beatbot; Pool Research; HTH Algae Guard Advanced; HASA; EPA labels 5185-513, 7616-73, 8959-2, 69681-20, 57787-2; EPA PPLS count by PC&S. Accessed November 2026. Download CSV
The shock-then-algaecide timing is where makers disagree most. The HTH Algae Guard Advanced page says chlorine above 5 ppm can deactivate algaecide and to wait 24 hours, and HASA says high chlorine can oxidize polyquat, yet the Algae Complete label doses 1 hour after a shock. Follow the label of the product you hold; our pool shock guide gives the chlorine side of the dose.
How long after adding algaecide can you swim?
As long as the label says, which runs from no wait to 6 hours. Swimtrine and Pool Trol allow swimming immediately, HTH Algae Stop, Algae Complete and MSA II say 15 minutes, Kem Tek allows 15 minutes only at 3 ppm chlorine or less, and Clor Mor Maintenance keeps swimmers out for 6 hours of filtration.
| Product (EPA Reg. No.) | Type | What the label says about swimming | Minutes (for the chart) |
|---|---|---|---|
| Swimtrine (8959-2) | Copper | Treated water can be used immediately, no waiting | 0 |
| Pool Trol Copper Algaecide (3525-141) | Copper | Can be used immediately, no waiting | 0 |
| Algae Kil CB 7 (57787-17) | Copper | Resume immediately when chlorine is at or below 4 ppm | 0 |
| HTH Algae Stop (1258-1288) | Quat 30% | Wait 15 minutes before entering pool | 15 |
| BioGuard Algae Complete (5185-513), prevention | Copper + polyquat | Wait at least 15 minutes; after a treatment dose, chlorine 1 to 4 ppm | 15 |
| BioGuard MSA Algaecide II (5185-382), prevention | Copper + quat | Wait at least 15 minutes | 15 |
| Kem Tek Algaecide (7616-73) | Polyquat 60% | 15 minutes, only when chlorine is 3 ppm or less | 15 |
| Yellowtrine (8959-52) | Sodium bromide | Swimming may resume a few hours after treatment | |
| Clor Mor Maintenance Algaecide (69681-20) | Quat 50% | Run the filter at least 6 hours; no swimmers during that time | 360 |
Sources: EPA labels 8959-2, 3525-141, 57787-17, 1258-1288, 5185-513, 5185-382, 7616-73, 8959-52, 69681-20. Accessed November 1, 2026. Download CSV
Source: EPA labels 8959-2, 3525-141, 57787-17, 1258-1288, 5185-513, 5185-382, 7616-73, 69681-20. Accessed November 1, 2026. Download chart data (CSV)

After a shock-plus-algaecide treatment, the chlorine sets the wait, not the algaecide: Algae Complete bars re-entry until free chlorine is 1 to 4 ppm. How fast a shock drops to that level is covered in our guide on how long after shocking a pool you can swim.
Why does algaecide foam, and how do you avoid it?
Foam comes from simple quats, which are surfactants. The 2024 MAHC Annex says simple quats tend to foam when overdosed, especially in pools with fountains or waterfalls, while polyquats do not foam even at the maximum label dose. Avoid it by measuring the dose for your real gallons or by using a polyquat where water splashes.
- Measure gallons first: an initial dose of HTH Algaecide (quat 10%) is 26 fl oz per 10,000 gallons, so guessing 15,000 gallons in a 10,000 gallon pool adds 13 fl oz more than the label rate.
- Stronger quat, smaller pour: HTH Algae Stop at 30% quat starts at 8 fl oz per 10,000 gallons and Clor Mor at 50% at 5.2 fl oz; the same cup of the wrong bottle is a large overdose.
- Water features: the MAHC Annex singles out fountains and waterfalls for quat foam; Pro Algaecide markets its polyquat as ideal for pools with attached spas.
- Read ‘non-foaming’ with care: the HTH Algaecide and Algae Stop master labels list ‘non-foaming’ as optional text even though both are simple quats, the type the MAHC Annex says foams when overdosed.
Will copper algaecide stain your pool?
It can, and the limits are close together. Leslie’s says staining may occur above 0.6 ppm copper, EPA links copper above 1.0 mg/L to blue-green staining, and the MAHC caps copper ion systems at 1.3 ppm. A 4 oz Swimtrine dose adds about 0.27 ppm to 10,000 gallons, so a full program can reach the first line in six weeks if no copper leaves. If blue-green marks have already formed, our pool stains guide shows how to confirm copper and lift it without draining.
| Product or limit | Dose per 10,000 gal | Copper in the label | Copper added (PC&S arithmetic) | Source |
|---|---|---|---|---|
| Swimtrine (8959-2), opening | 4 oz | 0.72 lb per gallon | 0.27 ppm | EPA label 8959-2 |
| Swimtrine, each 2-week maintenance | 2 oz | 0.72 lb per gallon | 0.13 ppm | EPA label 8959-2 |
| Pool Trol Copper (3525-141), initial | 4 oz | 0.76 lb per gallon | 0.28 ppm | EPA label 3525-141 |
| Black Algaetrine (8959-14), black algae | 12 oz | 0.27 lb per gallon | 0.30 ppm | EPA label 8959-14 (PC&S black algae guide) |
| Staining may occur above | 0.6 ppm | Leslie's black algae guide | ||
| EPA secondary standard (blue-green staining) | 1.0 mg/L | EPA secondary drinking water standards | ||
| MAHC maximum for copper ion systems | 1.3 ppm | 2024 MAHC 5.7.3.2.3.2 |
Sources: EPA labels 8959-2, 3525-141, 8959-14; Leslie’s black algae guide; EPA secondary standards (May 2026); 2024 MAHC 5.7.3.2.3.2; NIST conversions. Copper ppm is PC&S arithmetic: fl oz / 128 x lb copper per gallon x 453.6 g / 37,854 L. Download CSV
Source: EPA label 8959-2 (0.72 lb copper per gallon); Leslie's; EPA secondary standards (May 2026); 2024 MAHC 5.7.3.2.3.2; NIST conversions. Download chart data (CSV)
The chart is a ceiling, not a forecast: backwashing, splash-out, rain and precipitation all remove copper, so test it rather than assume. pH is the lever. The MAHC Annex calls pH control very important to minimize staining with copper algaecides, and the SeaKlear label (45729-5) sets pH 7.2 to 7.8 and alkalinity 80 to 120 ppm. Above that label’s 7.8 pH ceiling, hold off on copper until pH is back down.
Two setups should skip copper entirely. The MAHC Annex says copper-based algaecides should not go into pools with copper and silver ion systems, and that copper speeds the formation of trihalomethanes during chlorination. And the MSA Algaecide II label itself recommends a stain and scale control 2 days after the last treatment to pull leftover copper out of the water. Which copper ionizers hold an EPA registration, and the copper range each label sets, are listed in our pool ionizer guide.
Rather have a pro handle the algae?
Algaecide or shock: which does your pool need?
Shock kills a bloom; algaecide prevents the next one or finishes chlorine-tolerant growth. If the water is green or cloudy, shock and filter first. If chlorine holds and algae stays away, skip routine algaecide. Use a labeled algaecide for mustard or black algae, vacations and winter, and pick the type by your water features, a copper reading of 0.6 ppm or more, and your sanitizer.
| Number | What it means | Source |
|---|---|---|
| 175 | Active EPA registrations named algaecide or algicide with a swimming pool use site, November 1, 2026 | EPA PPLS, counted by PC&S |
| 11 to 17 fl oz | HTH Non-Foaming 60 dose per 10,000 gal for visible algae | EPA label 1258-1080 |
| 2 to 4 fl oz | Polyquat 60% maintenance per 10,000 gal every 5 to 7 days | EPA labels 1258-1080, 3525-117 |
| 0 to 6 hours | Range of label swim waits | EPA labels 8959-2, 69681-20 |
| 0.27 ppm | Copper from a 4 oz opening dose of Swimtrine in 10,000 gal (PC&S arithmetic) | EPA label 8959-2 |
| 0.6 ppm | Copper level above which Leslie's says staining may occur | Leslie's |
| 1.0 mg/L | EPA secondary standard for copper (blue-green staining) | EPA |
| 1.3 ppm | MAHC maximum copper for copper ion systems at public pools | 2024 MAHC 5.7.3.2.3.2 |
| 1 to 4 ppm | Free chlorine window before re-entry after an Algae Complete treatment dose | EPA label 5185-513 |
Sources: EPA PPLS; EPA labels 1258-1080, 3525-117, 8959-2, 69681-20, 5185-513; Leslie’s; EPA; 2024 MAHC. Accessed November 2026. Download CSV
| If your situation is | Do this | Why (source) |
|---|---|---|
| Water is green or you cannot see the floor | Shock to the label algae dose and filter; algaecide comes after, not instead | HTH Algae Stop label 1258-1288: heavy growth must be cleaned first; HASA |
| Free chlorine holds at the level your CYA needs and no algae returns | Skip routine algaecide | HASA: a properly maintained pool may not need a routine algaecide |
| Yellow dust in shady spots that returns after brushing | Shock plus an algaecide labeled for mustard algae | EPA labels 5185-513, 3525-117; PC&S mustard algae guide |
| Raised dark spots in plaster | Brush hard, then a product labeled for black algae | EPA label 8959-14; PC&S black algae guide |
| Fountains, waterfalls or a spillover spa | Use a polyquat, not a simple quat | MAHC Annex 5.7.4.4.4: simple quats foam when overdosed |
| Copper already reads 0.6 ppm or more, or a copper ionizer is installed | Use a polyquat; no copper algaecide | Leslie's; MAHC Annex 5.7.3.2.3 |
| Biguanide (non-chlorine) sanitizer | Do not use Algae Complete | EPA label 5185-513 |
| Outdoor pool and a sodium bromide product | Do not use it; the label bars outdoor pools | EPA label 8959-52 |
| Leaving the pool for a week or closing for winter | Add the label vacation or winter dose (Clor Mor: 4.8 oz per 10,000 gal per week) | EPA labels 69681-20, 1258-1080 |
Sources: HASA; 2024 MAHC Annex; Leslie’s; EPA labels 1258-1080, 5185-513, 3525-117, 8959-14, 8959-52, 69681-20. Accessed November 2026. Download CSV

Closing is the most common planned use. The HTH Non-Foaming 60 label sets a winter dose of 9 fl oz per 10,000 gallons, or 16 fl oz if some algae is visible, and our guide on how to winterize a pool places it after the closing shock. If cloudiness rather than algae is the problem after treatment, our pool flocculant guide covers clarifier and floc doses.
Algaecide safety rules from the labels
Treat algaecide as the pesticide it is. Wear the gloves the label names, add it to water separately and never premix it with chlorine, keep children away from the bottle, and drain treated water only where local authorities allow. CDC counts about 4,500 emergency department visits a year from pool chemical injuries, at least one third of them in people under 18.
How we compiled this
We read 22 EPA-accepted algaecide labels (17 are cited) and 223 registration records from EPA’s Pesticide Product and Label System on November 1, 2026, plus the 2024 Model Aquatic Health Code and Annex, EPA and CDC guidance, a HASA technical blog, HTH and Leslie’s product pages and two PC&S research reports. Doses for other pool sizes, copper ppm and costs are PC&S arithmetic. We did not test any product; five consumer guides appear only where we compare their claims with the labels, and forum posts were excluded as a source of facts.
Frequently Asked Questions
How long after adding algaecide can I swim?
Check the label: it ranges from no wait to 6 hours. Swimtrine (8959-2) allows swimming immediately, HTH Algae Stop and BioGuard Algae Complete say 15 minutes, and Clor Mor Maintenance (69681-20) keeps swimmers out for at least 6 hours of filtration. After a shock-plus-algaecide treatment, Algae Complete adds a second test: free chlorine must be 1 to 4 ppm.
Can I add algaecide and chlorine at the same time?
Not mixed together. Pro Algaecide and Combat 30 bar mixing with concentrated chlorine, and Algae Kil CB 7 says never mix products in the same bottle or pail. In sequence they are designed to work together: the Algae Complete label adds 16 fl oz per 10,000 gallons 1 hour after a shock, and Kem Tek doses 16 oz after shocking to 5 ppm.
Do you put algaecide or shock first?
Shock first when algae is visible. The Algae Complete label circulates a shock for 1 hour before the algaecide, and Kem Tek shocks to 5 ppm first. The HTH Algae Guard Advanced page goes further, saying chlorine above 5 ppm can deactivate algaecide and to wait 24 hours, so follow the timing on your own bottle.
Why does my pool foam after I add algaecide?
You most likely used a simple quat and overdosed it. The 2024 MAHC Annex says simple quats tend to foam when overdosed, especially with fountains or waterfalls, while polyquats do not foam even at the maximum label dose. Check your gallons and the strength: a 50% quat such as Clor Mor needs 5.2 fl oz per 10,000 gallons.
Should I use algaecide every week?
Only if your label program and your pool call for it. Polyquat 60% labels set 2 to 4 fl oz per 10,000 gallons every 5 to 7 days and Algae Complete 1.5 fl oz weekly, but HASA says a pool with enough free chlorine for its CYA level may not need routine algaecide. A 16-week season costs $75.98 to $151.96 for 20,000 gallons.
Will algaecide clear a green pool?
Not on its own. The HTH Algae Stop label (1258-1288) says pools with heavy algae growth must be cleaned before use, and HASA calls algaecide-only treatment of a green pool a common mistake. Shock to the label algae dose, filter and vacuum first; EPA label 1258-1250 doses a severe bloom at 2.6 lb of 52% calcium hypochlorite per 10,000 gallons.
Sources
- U.S. Environmental Protection Agency. Pesticide Product and Label System, product name search ALGAECIDE (November 1, 2026). Accessed 2026-11-01.
- U.S. Environmental Protection Agency. Pesticide Product and Label System, product name search ALGICIDE (November 1, 2026). Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. HTH Algaecide, EPA Reg. No. 1258-1077, label file dated 2021-01-14. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. HTH Algae Stop, EPA Reg. No. 1258-1288, label file dated 2022-06-21. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Clor Mor Maintenance Algaecide, EPA Reg. No. 69681-20, label file dated 2025-12-22. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. HTH Non-Foaming Algaecide 60, EPA Reg. No. 1258-1080, label file dated 2025-09-16. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Kem Tek Algaecide, EPA Reg. No. 7616-73, label file dated 2026-05-20. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Combat 30, EPA Reg. No. 57787-2, label file dated 2026-01-21. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Swimtrine Algaecide, EPA Reg. No. 8959-2, label file dated 2025-04-14. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Pool Trol Copper Algaecide, EPA Reg. No. 3525-141, label file dated 2026-07-07. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Algitec 7.0, EPA Reg. No. 3432-79, label file dated 2026-05-26. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. SeaKlear Algae Prevention and Remover, EPA Reg. No. 45729-5, label file dated 2025-08-26. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Algae Kil CB 7, EPA Reg. No. 57787-17, label file dated 2024-03-28. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. BioGuard Algae Complete (BioLab T-0041), EPA Reg. No. 5185-513, label file dated 2025-07-16. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. BioGuard MSA Algaecide II, EPA Reg. No. 5185-382, label file dated 2026-08-06. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Yellowtrine, EPA Reg. No. 8959-52, label file dated 2025-04-15. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Pro Algaecide, EPA Reg. No. 3432-31, label file dated 2025-07-17. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Algon 60 Algaecide, EPA Reg. No. 3525-117, label file dated 2019-04-03. Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Black Algaetrine, EPA Reg. No. 8959-14, label file dated 2026-10-08. Accessed 2026-11-01.
- Centers for Disease Control and Prevention. 2024 Model Aquatic Health Code, 5th Edition, Code Language. Accessed 2026-11-01.
- Centers for Disease Control and Prevention. 2024 Model Aquatic Health Code, 5th Edition, Annex. Accessed 2026-11-01.
- U.S. Environmental Protection Agency. Secondary Drinking Water Standards: Guidance for Nuisance Chemicals (updated May 26, 2026). Accessed 2026-11-01.
- Centers for Disease Control and Prevention. Home Pool and Hot Tub Water Treatment and Testing (May 10, 2024). Accessed 2026-11-01.
- Centers for Disease Control and Prevention. Pool Chemical Emergencies (May 28, 2025). Accessed 2026-11-01.
- HASA (manufacturer). Do You Need an Algaecide? When and Why to Use One. Accessed 2026-11-01.
- HTH (manufacturer). HTH Pool Care Algae Guard Advanced. Accessed 2026-11-01.
- Leslie's (retailer). How to Treat Black Algae in Your Pool. Accessed 2026-11-01.
- Leslie's via PC&S pool equipment price index. Leslie's Algae Control 1 qt (Wayback Machine capture September 16, 2026). Accessed 2026-11-01.
- National Institute of Standards and Technology. Approximate Conversions from U.S. Customary Measures to Metric. Accessed 2026-11-01.
- PC&S research. Pool Season Length by City (NOAA 1991 to 2020 normals). Accessed 2026-11-01.
- NOAA National Centers for Environmental Information. U.S. Climate Normals. Accessed 2026-11-01.
- PC&S research. Pool Equipment Prices 2026. Accessed 2026-11-01.
- Simplified Pools (retailer blog). Pool Algaecide Guide: Types, When to Use Them (guide claims compared). Accessed 2026-11-01.
- Poolonomics. Best Pool Algaecide (guide claims compared). Accessed 2026-11-01.
- Hunker. How To Use Algaecide (guide claims compared). Accessed 2026-11-01.
- Beatbot (manufacturer blog). How to Use Algaecide in Swimming Pools the Right Way (guide claims compared). Accessed 2026-11-01.
- Pool Research. A Guide to Using Algaecide in Your Pool (guide claims compared). Accessed 2026-11-01.
- U.S. EPA Pesticide Product and Label System. Arch 52% Calcium Hypochlorite, EPA Reg. No. 1258-1250, draft label dated July 12, 2021. Accessed 2026-11-01.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.