
How to Drain a Hot Tub, Refill It and Avoid an Air Lock
How to drain a hot tub: switch it off at the breaker, drain through the spigot or a submersible pump to a lawn or sewer cleanout, then refill through the filter compartment to avoid an air lock.
- ✓Drain-time tableMinutes for 190 to 525 gallon tubs at five sourced flow rates, from a slow spigot to a 30 gpm pump.
- ✓Five maker manuals comparedHot Spring, Master Spas, Coast, Catalina and Nordic: valve location, refill level and air lock steps.
- ✓Discharge rules that name hot tubsPortland, Yakima County and West Valley, CA set cooling, chlorine and flow limits for spa water.
Key takeaways
- Hot Spring’s 2026 Highlife owner’s manual says to change chlorine or bromine water every 3 to 4 months, and up to 12 months with its FreshWater Salt System.
- The 2024 Model Aquatic Health Code sets public spa water changes at gallons divided by 3, divided by average daily users: 455 gallons and 2 users a day gives 75.8 days.
- A 1/4 HP K2 UTA02502K utility pump moves 1,800 gallons per hour at 0 ft of lift, so a 455 gallon tub empties in about 15 minutes; a spigot takes 45 to 90 minutes for 400 to 500 gallons, per Jacuzzi.
- Portland, Oregon bars heated, chlorinated, bromine or salt water from storm drains; as a last resort it allows cooled water at 0.1 mg/L chlorine or less, under 50 gpm.
- Catalina Spas fills through the empty filter canister to about 1 in over the highest jets and warns never to run an unprimed pump for more than 2 minutes.
How often should you drain a hot tub?
Every 3 to 6 months for most home tubs, by the owner’s manuals: Hot Spring says 3 to 4 months for chlorine or bromine water, Coast Spas 3 to 6 and Catalina 4 to 6. Heavy use shortens that. The public-spa formula in the 2024 Model Aquatic Health Code, gallons divided by 3 and then by daily users, gives about 76 days for a 455 gallon tub soaked in twice a day.
| Source | Document | Water change interval | Condition or trigger | Source link |
|---|---|---|---|---|
| Hot Spring | 2026 Highlife owner's manual | 3 to 4 months | Up to 12 months with the FreshWater Salt System | https://d1oxc6ayqrhsgs.cloudfront.net/hot-spring/hot-spring-highlife-collection-owners-manuals-2026.pdf |
| Coast Spas | 2026 Purfikt Series owner's manual | 3 to 6 months | Detergent and soap film build up after 3 to 4 months | https://coastspas.com/downloads/2026%20Owners%20Manual%20-%20Purfikt%20Series.pdf |
| Catalina Spas | Owner's manual (2022 file) | 4 to 6 months | Depends on how many people use the spa and how often | https://catalinaspas.com/wp-content/uploads/2022/12/Catalina-Spas-Owners-Manual.pdf |
| Master Spas | 2025 Getaway owner's manual | At least every 180 days | Heavy bather load means more often | https://masterspascdn.com/documents/_manuals/getaway/2025-getaway-spas-owners-manual.pdf |
| Nordic Hot Tubs | Owner's manual (2023 file) | Every 3 months | Listed in the maintenance schedule | https://www.nordichottubs.com/wp-content/uploads/2023/12/Nordic-hot-tubs-Owners-Manual_060923.pdf |
| CDC Model Aquatic Health Code | 2024 MAHC, 5.12.1.2.1 (public spas) | Gallons / 3 / average users per day | Or at a minimum of every 1 to 2 weeks | https://www.cdc.gov/model-aquatic-health-code/media/pdfs/2024/11/5th-Ed-MAHC-Code-508.pdf |
Sources: Hot Spring 2026 Highlife manual; Coast Spas 2026 manual; Catalina Spas manual; Master Spas 2025 Getaway manual; Nordic Hot Tubs manual; CDC 2024 MAHC. Accessed 2026-10-26. Download CSV
MAHC: 455 / 3 / 2 = 75.8 days, about 2.5 months. The MAHC formula is written for public spas.
Source: Owner's manuals from Hot Spring (2026), Coast Spas (2026), Catalina Spas, Master Spas (2025) and Nordic Hot Tubs; CDC 2024 MAHC 5.12.1.2.1; accessed 2026-10-26. Download chart data (CSV)
The formula is a cross-check, not a home rule. Jacuzzi applies it to a 200 gallon tub with 4 bathers a day and gets a drain every 16 days or so, while Cal Spas works 400 / 3 / 2 to 67 days. The MAHC text adds “or at a minimum of every 1 to 2 weeks” for public spas (5.12.1.2.1).
| Tub | Gallons | Users per day | Arithmetic | Days between changes |
|---|---|---|---|---|
| Hot Spring Hot Spot TX | 190 | 2 | 190 / 3 / 2 | 31.7 |
| Sundance Chelsee | 400 | 2 | 400 / 3 / 2 | 66.7 |
| Hot Spring Grandee | 455 | 2 | 455 / 3 / 2 | 75.8 |
| Hot Spring Grandee | 455 | 4 | 455 / 3 / 4 | 37.9 |
Formula: 2024 MAHC 5.12.1.2.1; gallons from Hot Spring and Sundance spec pages. Arithmetic by PC&S. Download CSV
Water that will not hold its chemistry is the other trigger. Coast Spas says detergent and soap film build up after 3 to 4 months and the water turns cloudy; Hot Spring says soap build-up eventually makes the water feel unclean in a way no chemical fixes. Our guide on how to lower pH in a hot tub covers the doses to try before a drain, and the weekly routine sits in our hot tub maintenance guide. Foam that returns with every reading in range is the same signal, and our guide to hot tub foam ranks its causes from 9 makers’ manuals.
Where is the hot tub drain valve?
Behind the front access panel on the equipment side in most tubs. Hot Spring puts the main drain valve below the front panel with a secondary drain for the bleed lines; Master Spas puts it in the equipment bay behind the front skirt, on the same side as the topside controls; Catalina places it in the base near one corner. Hot Spring’s secondary drain releases about 1 more gallon.
| Maker manual | Where the drain valve is | How it opens | What stays in the tub | Source link |
|---|---|---|---|---|
| Hot Spring (2026 Highlife) | Main drain valve below the front panel, plus a secondary drain | Remove the cap, attach a garden hose, turn the knob; gravity does the rest | About 1 gallon in the bleed lines until the secondary drain cap comes off | https://d1oxc6ayqrhsgs.cloudfront.net/hot-spring/hot-spring-highlife-collection-owners-manuals-2026.pdf |
| Master Spas (2025 Getaway) | Inside the equipment bay behind the front skirt, same side as the topside controls | Remove the cap, twist the face counterclockwise and pull out slightly | Small pockets the manual says a shop vac can pick up | https://masterspascdn.com/documents/_manuals/getaway/2025-getaway-spas-owners-manual.pdf |
| Coast Spas (2026 Purfikt) | Usually in the equipment area | Remove the safety cap, attach a hose, then open the filter lid air relief valve once water flows | A small portion in the foot well, removed with a sponge and pail | https://coastspas.com/downloads/2026%20Owners%20Manual%20-%20Purfikt%20Series.pdf |
| Catalina Spas | In the base of the spa near one of the corners | Drain valve with a hose bib; GFCI off first | Not stated | https://catalinaspas.com/wp-content/uploads/2022/12/Catalina-Spas-Owners-Manual.pdf |
| Nordic Hot Tubs (2023) | Drain fitting that takes a regular garden hose | Remove the safety cap, connect a garden hose | Not stated; a small submersible pump is the stated alternative | https://www.nordichottubs.com/wp-content/uploads/2023/12/Nordic-hot-tubs-Owners-Manual_060923.pdf |
Sources: Hot Spring; Master Spas; Coast Spas; Catalina Spas; Nordic Hot Tubs owner’s manuals, accessed 2026-10-26. Download CSV
Thread the hose on by hand, and use at least 25 ft of it (Jacuzzi). Hot Spring’s blog warns that spigot threads are plastic and can break if cross-threaded, and that a hose run uphill drains only part of the water, so run it downhill or level to the outlet. If your model has two spigots, open the primary first and the auxiliary one last to empty the internal bleed lines.
How to drain a hot tub, step by step
Plan the outlet, cut power at the breaker, let the water cool, attach a hose to the drain valve or set a pump on the floor, drain to a lawn or sewer cleanout, open the secondary drain or air relief valve, sponge out the foot well, clean the filters, then close the valve and cap it. Allow 41 to 102 minutes by spigot or 15 to 18 minutes by pump for a 455 gallon tub. Drain day is also soak day: Caldera soaks its cartridges overnight at each water change, as our guide on how to clean a hot tub filter explains.
| Number | What it means | Source |
|---|---|---|
| 3 to 4 months | Water change interval for chlorine or bromine water in a Hot Spring Highlife spa | Hot Spring 2026 Highlife owner's manual |
| Up to 12 months | Water life Hot Spring gives with its FreshWater Salt System and proper care | Hot Spring 2026 Highlife owner's manual |
| Gallons / 3 / daily users | Days between water changes for a public spa | CDC 2024 Model Aquatic Health Code 5.12.1.2.1 |
| 50 to 70 F | Refill water temperature that avoids a high-limit trip | Hot Spring 2026 Highlife owner's manual |
| About 1 gallon | Water left in the bleed lines that the secondary drain removes | Hot Spring 2026 Highlife owner's manual |
| 1,800 GPH (30 gpm) | Flow of a 1/4 HP K2 UTA02502K utility pump at 0 ft of lift | K2 spec sheet |
| 12 gpm | Most a pump may send into a sewer cleanout or indoor drain in Yakima County, WA | Yakima County Regional Stormwater Group |
| 0.1 mg/L | Total residual chlorine limit before any storm sewer discharge in Portland, OR | Portland Bureau of Environmental Services |
Sources: 2026 Highlife owner’s manual; CDC 2024 MAHC; K2 spec sheet; Yakima County; Portland BES. Accessed 2026-10-26. Download CSV
- Pick the day and the outletAir above 50 F so you can refill the same day (Hot Spring). Choose a lawn that will not run to the street, or a sewer cleanout at 12 gpm or less (Yakima County).
- Let the sanitizer dropStop adding chlorine at least 3 days ahead and check that pH is 6 to 8 (Yakima County). Test strips confirm it.
- Cut the powerTrip both GFCI breakers in the subpanel (Hot Spring). Tubs on more than one circuit need every breaker off (Master Spas).
- Let the water coolBelow 100 F before you handle hose fittings (Jacuzzi). Portland asks for at least 12 hours of cooling before any storm sewer discharge.
- Open the drainRemove the front panel and the drain cap, screw a hose of at least 25 ft onto the valve, 3/4 in diameter if you have one (Jacuzzi), and open the valve. Or lower a submersible pump to the foot well; a 1/4 HP K2 moves 1,550 gallons per hour at 5 ft of lift.
- Clear the linesWhen the water starts to flow, open the filter lid air relief valve (Coast Spas). Near the end, open the secondary drain to release about 1 gallon from the bleed lines (Hot Spring).
- Remove what is leftSponge the foot well into a pail (Coast Spas) or use a shop vac (Master Spas). Turn a pump off once it starts sucking air.
- Clean the shell and filtersClean and rotate the filter cartridges every time you drain (Hot Spring). Do not leave the empty shell in direct sun for long (Coast Spas).
- Close upClose the valve, refit the drain cap and secondary cap, and check slice valves are open before refilling (Catalina; Master Spas).

How long does it take to drain a hot tub?
Divide the gallons by the flow in gallons per minute. A 400 gallon tub takes 13 minutes with a 1/4 HP pump at 30 gpm, 15 minutes at 5 ft of lift, 33 minutes at Yakima County’s 12 gpm cap and 36 to 90 minutes through the spigot, using the 45 to 90 minutes Jacuzzi gives for a 400 to 500 gallon spa. Find your gallons on the spec page.
| Tub (maker spec) | Gallons | Spigot, slow (4.4 gpm) | Spigot, fast (11.1 gpm) | Yakima cleanout cap (12 gpm) | 1/4 HP pump, 5 ft lift (25.8 gpm) | 1/4 HP pump, 0 ft lift (30 gpm) |
|---|---|---|---|---|---|---|
| Hot Spring Hot Spot TX | 190 | 43 | 17 | 16 | 7 | 6 |
| Hot Spring Jetsetter | 245 | 55 | 22 | 20 | 9 | 8 |
| Hot Spring Hot Spot Pace | 300 | 68 | 27 | 25 | 12 | 10 |
| Sundance Optima | 355 | 80 | 32 | 30 | 14 | 12 |
| Sundance Chelsee | 400 | 90 | 36 | 33 | 15 | 13 |
| Hot Spring Grandee | 455 | 102 | 41 | 38 | 18 | 15 |
| Hot Spring Limelight Prism | 525 | 118 | 47 | 44 | 20 | 18 |
Sources: gallons from Hot Spring and Sundance spec pages; rates from Jacuzzi, Yakima County and the K2 spec sheet; PC&S arithmetic. Accessed 2026-10-26. Download CSV
Spigot rates are implied by Jacuzzi's 45 to 90 minutes for a 400 to 500 gallon spa.
Source: PC&S arithmetic from Jacuzzi (spigot times), Yakima County (12 gpm cap) and the K2 UTA02502K spec sheet, accessed 2026-10-26. Download chart data (CSV)
| Step | Input | Result | Source |
|---|---|---|---|
| Tub volume | Hot Spring Grandee spec | 455 gallons | Hot Spring Grandee spec page |
| Pump flow at 5 ft of lift | 1,550 GPH / 60 | 25.8 gpm | K2 UTA02502K spec sheet |
| Pump drain time | 455 / 25.8 | 17.6 minutes | PC&S arithmetic |
| Same tub at the Yakima 12 gpm cap | 455 / 12 | 37.9 minutes | Yakima County |
| Spigot, slow case | 455 / 4.4 | 102 minutes | Jacuzzi: 400 gal in 90 minutes |
| Spigot, fast case | 455 / 11.1 | 41 minutes | Jacuzzi: 500 gal in 45 minutes |
| Water to refill | 455 x $10.75 per 1,000 gal | $4.89 | PC&S cost to fill a pool ledger, 25-city median |
Sources: Hot Spring Grandee spec; K2 spec sheet; Yakima County; Jacuzzi; PC&S cost to fill a pool ledger. Download CSV
What is the easiest way to drain a hot tub? A submersible pump. Hot Spring puts it at about ten minutes against about an hour for the spigot, and Jacuzzi at 10 to 15 minutes against 45 to 90. The 1/4 HP K2 in our table loses flow as it lifts water higher: 1,800 gallons per hour at 0 ft, 1,550 at 5 ft and 1,320 at 10 ft.
| Method | Time for a 400 to 500 gallon tub | What you need | Leaves behind | Source |
|---|---|---|---|---|
| Built-in drain spigot with a garden hose | 45 to 90 minutes (Jacuzzi); about an hour (Hot Spring) | Hose of at least 25 ft, 3/4 in diameter preferred (Jacuzzi) | Foot well water and bleed lines (Hot Spring; Coast) | Jacuzzi; Hot Spring |
| Submersible utility pump | 10 to 15 minutes (Jacuzzi); about 10 minutes (Hot Spring) | Pump, discharge hose, an outlet | About the last inch (Jacuzzi) | Jacuzzi; Hot Spring; Master Spas |
| Garden hose siphon | Depends on the height drop; no maker figure | Hose filled with water, outlet below the tub floor | Water below the hose inlet | Master Spas lists the garden hose as a third way |
| Shop vacuum | Finishing step only | Wet/dry shop vac | Nothing in the shell; plumbing lines need it for winterizing | Master Spas; Coast Spas |
Sources: Jacuzzi; Hot Spring; Master Spas manual; Coast Spas manual. Download CSV
How do you empty a hot tub without a pump? Use the spigot and gravity, or siphon with a garden hose. Fill the hose with water, put one end on the tub floor and run the other end to an outlet lower than the floor. Master Spas lists the garden hose as one of three drain methods. No maker publishes a siphon flow rate, so plan on more than the 45 to 90 minutes Jacuzzi gives for the spigot.
Where can you drain hot tub water?
To the sanitary sewer through a cleanout or indoor drain, or onto your own lawn once the sanitizer has dropped, and to a storm drain only where a local rule allows it. Portland bars heated, bromine and salt water from storm drains outright, Yakima County caps cleanout flow at 12 gpm, and the West Valley Stormwater Authority in California says never into a septic system or toilet.
| Jurisdiction | Storm drain | Chlorine and wait | Flow limit | Bromine or salt water | Preferred route | Source link |
|---|---|---|---|---|---|---|
| Portland, OR (Bureau of Environmental Services) | Only if no other option | 0.1 mg/L total residual chlorine or less; sit at least 2 weeks; cool at least 12 hours; neutral pH | Less than 50 gpm | Prohibited from the stormwater system | Sanitary sewer or infiltrate on site | https://www.portland.gov/bes/preventing-pollution/prevent-pollution/drain-pools-and-hot-tubs |
| Yakima County, WA (Regional Stormwater Group) | Illegal | No chlorine added for at least 3 days; pH 6 to 8; verify with a test kit | No more than 12 gpm to a sewer cleanout or indoor drain | Salt water may damage plants or soil | Lawn or sanitary sewer cleanout | https://www.wastormwatercenter.org/document/yakima-county-guidelines-for-proper-pool-spa-and-fountain-drainage/ |
| West Valley Stormwater Authority, CA (Campbell, Los Gatos, Monte Sereno, Saratoga) | No | Dechlorinate 5 to 10 days in the sun or with a chemical; test | Not stated | Not stated | Spas: garden hose to a sewer cleanout or an indoor drain such as a bathtub; never a septic system or toilet | https://www.cleancreeks.org/292/Draining-Pools-Spas-and-Fountains |
| Mansfield, TX | Not listed as a route | Chlorine 0.5 ppm or less; cyanuric acid 20 ppm or less | No more than 50 gpm into a sewer cleanout, 2 in air gap | Not stated | Sewer cleanout or yard | https://www.mansfieldtexas.gov/2167/How-to-Drain-Your-Swimming-Pool |
| Washington, DC (Department of Energy and Environment) | Only after chlorine is under 0.1 mg/L | Under 0.1 mg/L; first offense fine up to $1,000, doubling each repeat | Not stated | Not stated | Sanitary or combined sewer through household plumbing | https://doee.dc.gov/service/how-drain-your-swimming-pool-properly |
| U.S. EPA (stormwater guidance to cities) | Only after dechlorinating | Dechlorinate first | Not stated | Not stated | Sanitary sewer, or dechlorinate then discharge or irrigate | https://www.epa.gov/system/files/documents/2023-01/bmp-educating-residents-on-safely-discharging-chemically-treated-water.pdf |
Sources: Portland BES; Yakima County; West Valley Stormwater Authority; City of Mansfield; DC DOEE; U.S. EPA. Accessed 2026-10-26. Download CSV

Heat is the hot tub problem that pool rules miss. Portland’s Bureau of Environmental Services lists heated water next to chlorinated and salt-treated water as a prohibited storm drain discharge under City Code 17.39, and its last-resort route needs 12 hours of cooling and two weeks of standing time. The U.S. EPA’s stormwater guidance for cities names hot tubs alongside pools and lists the sanitary sewer, or dechlorinating and then discharging or irrigating, as the accepted routes.
Bromine changes the answer. Portland City Code 17.39 bars water containing bromine or copper from its stormwater system whatever the chlorine reading, so a bromine tub goes to the sanitary sewer or the lawn. Our comparison of chlorine vs bromine explains why bromine is common in spas. For pool-sized volumes and city-by-city flow caps, see our guide on how to drain a pool.

How do you refill a hot tub without an air lock?
Put the hose in the empty filter compartment, not the open tub, so water fills the pump and heater lines from below and pushes the air out. Fill to the maker’s level, about 1 in over the highest jets for Catalina or 2 in over the skimmer for Nordic, keep the water at 50 to 70 F for Hot Spring, and only then restore power.
| Maker manual | Where to put the hose | Fill to | Before power on | Source link |
|---|---|---|---|---|
| Hot Spring (2026 Highlife) | Filter compartment, through the Clean Screen pre-filter | Not stated in the refill steps | Refill water at 50 to 70 F; do not refill when the air is below 50 F | https://d1oxc6ayqrhsgs.cloudfront.net/hot-spring/hot-spring-highlife-collection-owners-manuals-2026.pdf |
| Catalina Spas | Empty filter canister | About 1 in over the highest jets, excluding neck jets | Slice valves up and locked; soak new filters 30 minutes; never run an unprimed pump more than 2 minutes | https://catalinaspas.com/wp-content/uploads/2022/12/Catalina-Spas-Owners-Manual.pdf |
| Master Spas (2025 Getaway) | Filter area | At least 1 in above the filter housing opening | Slice valves open; run each jet pump to check for an air lock | https://masterspascdn.com/documents/_manuals/getaway/2025-getaway-spas-owners-manual.pdf |
| Nordic Hot Tubs (2023) | Empty filter canister | At least 2 in over the filter skimmer | Do not use water from a water softener | https://www.nordichottubs.com/wp-content/uploads/2023/12/Nordic-hot-tubs-Owners-Manual_060923.pdf |
Sources: Hot Spring; Catalina Spas; Master Spas; Nordic Hot Tubs owner’s manuals, accessed 2026-10-26. Download CSV
If a pump hums but the jets stay flat after power on, that is an air lock. Catalina says an unprimed pump must not run longer than 2 minutes and that letting a pump run with an air lock will destroy it; Master Spas tells owners to run each jet pump at start-up to check, and its pump unions exist partly to bleed trapped air.
Refilling costs little in water. At the $215.09 median for 20,000 gallons in our cost to fill a pool ledger of 25 cities, a 455 gallon refill comes to about $4.89. Drought rules are the bigger risk: our pool filling restrictions atlas found 15 of 32 reviewed jurisdictions can ban filling pools at some drought stage, so check if your utility’s rule covers spas before you drain.
Should you drain your hot tub now, wait or change the plan?
Drain when the water is 3 to 4 months old or the chemistry will not hold, and wait if the air is below 50 F. Bromine or salt water goes to the sanitary sewer or a lawn, never a storm drain, and septic homes use the lawn. The table pairs each situation with the rule or manual behind it.
| If your situation is | Do this | Why (source) |
|---|---|---|
| Chlorine or bromine water is 3 to 4 months old | Drain and refill | Hot Spring 2026 Highlife manual interval |
| pH or sanitizer will not hold after several small doses | Drain and refill rather than adding more chemicals | Coast Spas: cloudy water after 3 to 4 months of soap film |
| The air is below 50 F, or freezing is forecast | Wait, or drain with a pump and refill the same day | Hot Spring: no refill below 50 F; Master Spas: drain quickly in freezing weather |
| Water is bromine or salt treated | Send it to the sanitary sewer or a lawn, never a storm drain | Portland City Code 17.39 bars bromine and salt water from the stormwater system |
| You have a septic system | Drain to a lawn that can absorb it instead | West Valley Stormwater Authority: never drain into a septic system |
| Your lawn slopes to the street or a neighbor | Use a sewer cleanout or indoor drain at 12 gpm or less | Yakima County |
| The pump hums but jets do not flow after refilling | Shut it off within 2 minutes and bleed the air | Catalina Spas: an unprimed pump can be destroyed |
| You are moving the tub | Drain it fully first; a filled tub weighs thousands of pounds | Hot Spring spec pages list 2,570 to 6,795 lb filled |
Sources: Hot Spring; Coast Spas; Master Spas; Catalina Spas; Portland BES; West Valley Stormwater Authority; Yakima County; Hot Spring spec pages. Download CSV
Moving a tub is the other reason to empty it. Hot Spring’s filled weights run from 2,570 lb for the 190 gallon TX to 6,795 lb for the 525 gallon Prism, and the model-by-model load table in our hot tub weight guide shows what a deck or pad must carry once it is refilled. Water, chemicals and covers are priced in our hot tub cost guide.
How we compiled this
In October 2026 we read five hot tub owner’s manuals (Hot Spring 2026, Master Spas 2025, Coast Spas 2026, Catalina Spas, Nordic Hot Tubs), the 2024 Model Aquatic Health Code, discharge rules from Portland, Yakima County, the West Valley Stormwater Authority, Mansfield and Washington DC, the U.S. EPA stormwater guidance, the K2 pump spec sheet and seven Hot Spring and Sundance spec pages. Drain times and refill cost are our arithmetic; we did not drain or test any tub. Forum posts were used only for question wording.
Frequently Asked Questions
What is the easiest way to drain a hot tub?
A submersible pump in the foot well with a hose to a lawn or sewer cleanout. Jacuzzi puts it at 10 to 15 minutes for most home tubs, against 45 to 90 minutes through the spigot. A 1/4 HP K2 UTA02502K moves 1,800 gallons per hour at 0 ft of lift, about 13 minutes for 400 gallons. Turn the tub off at the breaker first.
Can you drain a hot tub with a garden hose?
Yes. Thread a garden hose onto the drain spigot behind the front panel and open the valve; Hot Spring says it takes around an hour. Jacuzzi suggests at least 25 ft of hose and a 3/4 in diameter over 5/8 in for faster flow. Run the hose downhill or level, since an uphill run leaves water in the tub.
Where is the hot tub drain valve?
Usually behind the front access panel on the equipment side. Hot Spring puts the main drain valve below the front panel and adds a secondary drain for the bleed lines; Master Spas puts it in the equipment bay on the same side as the topside controls; Catalina places it in the base near one corner. Hot Spring’s secondary drain empties about 1 gallon from the bleed lines.
How to empty a hot tub without a pump?
Use the built-in spigot and gravity, or a garden hose siphon. For a siphon, fill the hose with water, keep one end on the tub floor and run the other end to an outlet lower than the floor. Gravity through the spigot takes 45 to 90 minutes for a 400 to 500 gallon spa (Jacuzzi). Sponge or shop-vac the last water from the foot well.
Can I just drain my hot tub and leave it empty?
Not for long. Coast Spas warns not to leave a drained spa in direct sunlight for extended periods because extreme heat can damage it, and Master Spas says water left in the plumbing can freeze and cause damage its warranty does not cover. Hot Spring also says not to refill when the air is below 50 F, so an empty tub in winter needs its lines vacuumed as the manual’s winterizing steps describe. If the tub is being retired rather than refilled, our hot tub removal cost guide lists what haulers charge once it is drained and disconnected.
How often should you fully drain a hot tub?
Every 3 to 4 months for chlorine or bromine water in Hot Spring’s 2026 manual, every 3 to 6 months in Coast Spas’ manual and 4 to 6 months in Catalina’s. Heavy use shortens it: the MAHC public-spa formula, gallons divided by 3 and then by daily users, gives 66.7 days for a 400 gallon tub used by 2 people a day.
Sources
- Hot Spring Spas. How to Drain a Hot Tub, Refill it, and Get it Ready for Use. Accessed 2026-10-26.
- Hot Spring Spas (Watkins Wellness). Highlife Collection 2026 Owner's Manual (Drain and Refill Instructions). Accessed 2026-10-26.
- Master Spas. 2025 Getaway Spas Owner's Manual (Draining Your Spa). Accessed 2026-10-26.
- Coast Spas. 2026 Owner's Manual, Purfikt Series. Accessed 2026-10-26.
- Catalina Spas. Owner's Guide. Accessed 2026-10-26.
- Nordic Hot Tubs. Owner's Manual. Accessed 2026-10-26.
- Jacuzzi. How to Drain a Hot Tub: Complete Guide for Jacuzzi Owners. Accessed 2026-10-26.
- Jacuzzi. Signs It's Time to Drain and Refill. Accessed 2026-10-26.
- Cal Spas. Hot Tub Drain and Clean Schedule: How Often to Change Water. Accessed 2026-10-26.
- U.S. Centers for Disease Control and Prevention. 2024 Model Aquatic Health Code (5th edition), section 5.12.1.2.1. Accessed 2026-10-26.
- K2 Pumps (via Lowe's). UTA02502K Automatic Submersible Utility Pump spec sheet. Accessed 2026-10-26.
- City of Portland Bureau of Environmental Services. How to drain or empty your pool or hot tub to meet City rules and to prevent pollution. Accessed 2026-10-26.
- Regional Stormwater Group of Yakima County (via Washington Stormwater Center). Guidelines for Proper Swimming Pool, Spa and Fountain Drainage. Accessed 2026-10-26.
- West Valley Stormwater Authority, California. Draining Pools, Spas, and Fountains. Accessed 2026-10-26.
- City of Mansfield, Texas. How to Drain Your Swimming Pool. Accessed 2026-10-26.
- DC Department of Energy and Environment. How to Drain Your Swimming Pool Properly. Accessed 2026-10-26.
- U.S. Environmental Protection Agency. Educating Residents on Safely Discharging Chemically Treated Water. Accessed 2026-10-26.
- Hot Spring Spas. Hot Spot TX, Jetsetter, Pace, Grandee and Prism model specifications. Accessed 2026-10-26.
- Sundance Spas. Optima and Chelsee specifications (model year 2026). Accessed 2026-10-26.
- Pool Construction & Service research. Cost to Fill a Pool in 25 US Cities (water and sewer rate ledger). Accessed 2026-10-26.
- Pool Construction & Service research. Pool Filling Restrictions (drought rule atlas). Accessed 2026-10-26.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.