
How to Backwash a Pool Filter: Sand and DE Steps, Water Used and Changing the Sand
How to backwash a pool filter: turn the pump off, set the valve to BACKWASH, run 2 to 5 minutes until the sight glass clears, then RINSE 20 to 60 seconds and return to FILTER.
- ✓TriggerHayward backwashes ProSeries sand filters at 8 to 10 psi over the clean reading.
- ✓Not on a timerPentair warns that backwashing too often causes poor filtration.
- ✓Water outA Pentair Triton TR60 sends about 221 to 347 gallons to waste per cycle.
Key takeaways
- Hayward’s ProSeries manual sets the backwash trigger at 8 to 10 psi over the clean pressure; Pentair uses 10 psi, or a 30% drop on a flow meter such as 60 to 40 gpm (Pentair Triton guide).
- Backwash times differ by maker: about 2 minutes plus a 1/2 to 1 minute rinse on a Hayward ProSeries, about 3 minutes plus 30 seconds on a Pentair Sand Dollar, and 3 to 5 minutes on a Triton (Hayward ProSeries manual).
- Pentair’s sand filter guides say not to backwash on a timer such as every three days, because backwashing too often causes poor filtration (Pentair Sand Dollar guide).
- One backwash and rinse cycle sends roughly 116 to 407 gallons to waste across the sand filters we modeled; EPA’s WaterSense guide cites a California estimate that 23% of quantifiable pool water use goes to filter backwashes (EPA WaterSense).
- Phoenix bans backwash water from the street, alley and right-of-way and tells owners to reuse it on landscaping instead (City of Phoenix).
- Changing the sand means loading the exact label weight of No. 20 silica at 0.45 to 0.55 mm: 50 lb in a Hayward S144T up to 925 lb in a Pentair TR140 (Pentair Triton guide; Hayward).
When should you backwash a pool filter?
Backwash when the pressure gauge reads 8 to 10 psi over the clean reading on a Hayward ProSeries, or 10 psi over on Pentair sand and DE filters. Pentair names a 30% drop on a flow meter as the most accurate signal. Do not backwash on a timer: Pentair says backwashing too often causes poor filtration, and a new pool gets its first backwash after 48 hours.
| Filter (type) | Backwash when | Backwash time | Rinse time | Then | Source |
|---|---|---|---|---|---|
| Hayward ProSeries S144T to S360T2 (sand) | 8 to 10 psi over the clean pressure | About 2 minutes or less, until the sight glass is clear | 1/2 to 1 minute | FILTER | Hayward ProSeries manual |
| Pentair Sand Dollar and Cristal-Flo II (sand) | 10 psi over clean, or flow down 30% | About 3 minutes or until the water is clean | About 30 seconds | FILTER | Pentair sand filter guide |
| Pentair Triton TR40 to TR140 (sand) | 10 psi over a fresh backwash, or flow down 30% (60 to 40 gpm) | 3 to 5 minutes or until clean | About 30 seconds (slide valve: no rinse step) | FILTER | Pentair Triton guide (2025) |
| Intex SF60110-2, SF70110-2, SF80110-2 (above-ground sand) | Gauge in the yellow zone | Until the waste water runs clear | About 1 minute | FILTER | Intex owner manual |
| Hayward Pro-Grid DE2420 to DE7220 (DE) | 8 to 10 psi over the pre-coat pressure | About 2 minutes, until the waste water looks clean | 20 seconds (six-position valve) | Add fresh DE | Hayward Pro-Grid manual |
| Pentair FNS Plus FNSP36 to FNSP60 (DE) | About 10 psi over the Original Starting Pressure | Until the discharge runs clear | Not listed | Add 3.6 to 6 lb DE | Pentair FNS Plus guide (2025) |
| Pentair Clean & Clear Plus, Hayward SwimClear (cartridge) | No backwash: clean at 10 psi (Pentair) or 7 to 10 psi (Hayward) | Not applicable | Not applicable | Hose off the cartridges | Pentair; Hayward SwimClear manual |
Sources: Hayward ProSeries manual; Pentair Sand Dollar guide; Pentair Triton guide (2025); Intex SF owner manual; Hayward Pro-Grid manual; Pentair FNS Plus guide (2025); Pentair cartridge cleaning guide; Hayward SwimClear manual. Download CSV
What counts as the clean reading? The gauge reading right after the last backwash, or right after pre-coating on a DE filter. Pentair’s Triton guide puts it plainly: backwash when the gauge reads 10 psi higher than it would just after a backwash. On a variable speed pump that reading shifts with speed, so Pentair’s FNS Plus guide asks owners to log the pump RPM with it; our variable speed pool pump guide covers speed programs.
| What a guide says | Who says it | What the filter maker says | Primary source |
|---|---|---|---|
| Backwash a sand filter every 1 to 2 weeks | Royal Swimming Pools guide | Do not backwash solely on a timed basis such as every three days; backwashing too often causes poor filtration | Pentair Sand Dollar and Triton guides |
| Backwash once per week | EPA WaterSense table (2022), citing a 2010 study | Backwash at 10 psi over clean or a 30% flow drop; the same EPA guide also says a 10 psi rise usually means a backwash | Pentair Triton guide; EPA WaterSense text |
| Rinse for 1 to 2 minutes | Royal Swimming Pools guide | Rinse 1/2 to 1 minute (Hayward ProSeries), about 30 seconds (Pentair), 20 seconds on a Pro-Grid DE filter | Hayward ProSeries and Pro-Grid manuals; Pentair guides |
| Switch back to BACKWASH for another 1 to 2 minutes after the rinse | Royal Swimming Pools guide | One backwash until clear, one rinse, then FILTER | Hayward ProSeries manual; Pentair Triton guide |
| Add 1 to 2 pounds of DE per 10 sq ft | Royal Swimming Pools guide | 1.0 lb per 10 sq ft (Pentair FNS Plus, Quad DE); 1.25 lb per 10 sq ft (Hayward Pro-Grid) | Pentair FNS Plus guide; Hayward Pro-Grid manual |
| Replace the sand every 1 to 3 years | SwimmingPool.com (Pool Corporation) | Roughly 5 years before the first sand change (Hayward); 3 to 6 years (EPA WaterSense) | Hayward filter-types article (2023); EPA WaterSense |
| Replace the sand every 5 to 8 years | Inyo Pools how-to page | Same published range: Hayward about 5 years, EPA 3 to 6, HTH 1.5 to 3 | Hayward; EPA WaterSense; HTH sand label |
Sources: Royal Swimming Pools; EPA WaterSense (2022); Pentair Sand Dollar; Pentair Triton; Hayward ProSeries; Hayward Pro-Grid; Pentair FNS Plus; SwimmingPool.com; Inyo Pools; Hayward (2023); HTH. Download CSV
When should you hold off? After clarifier. HTH says not to backwash or clean the filter for at least 24 hours after dosing, so the filter keeps the clumped particles; our cloudy pool water guide covers the dose. Hayward’s ProSeries manual also starts new plaster pools on FILTER rather than BACKWASH, to keep plaster dust from clogging the laterals.
How do you backwash a sand filter step by step?
Turn the pump off, set the multiport valve to BACKWASH, run the pump until the sight glass runs clear, then switch to RINSE for 30 seconds to 1 minute and back to FILTER. Hayward’s ProSeries manual gives about 2 minutes of backwash; Pentair gives about 3 minutes for a Sand Dollar and 3 to 5 minutes for a Triton.
- Read the gauge and plan the outletNote the pressure. Run the backwash hose to an outlet your city allows (see the discharge table further down) and confirm the line is open, which is step 2 in the Pentair sand filter guide.
- Pump off, then turn the handleHayward and Pentair both say to stop the pump before moving the valve. Press the handle down before turning it to BACKWASH to protect the valve seal (Hayward).
- Backwash until clearStand clear of the filter and start the pump. Run until the sight glass or waste water is clear: about 2 minutes or less (Hayward ProSeries), about 3 minutes (Pentair Sand Dollar), 3 to 5 minutes (Pentair Triton).
- Pump off, set RINSEStop the pump and set the valve to RINSE, which sends water down through the sand and out the waste port to resettle the bed (Pentair).
- Rinse brieflyRun the pump for 1/2 to 1 minute (Hayward) or about 30 seconds (Pentair). Hayward says the rinse keeps dirty backwash water from returning to the pool.
- Back to FILTERPump off, valve to FILTER, pump on. Open the air relief valve until a steady stream of water comes out, and check that the gauge is back near the clean reading.
- Top up the waterRefill what left: 116 to 407 gallons per cycle on the sand filters in the water table below.
Hayward ProSeries rinse is 1/2 to 1 minute and Triton backwash is 3 to 5 minutes; the chart plots the upper ends.
Source: Source: Hayward ProSeries and Pro-Grid manuals; Pentair Sand Dollar guide and Triton guide (2025). Accessed October 2026.. Download chart data (CSV)
What if the filter has a slide valve or a cleaner? A two-position slide valve has no RINSE step: Pentair’s Triton guide goes straight from backwash to FILTER, and Hayward’s Pro-Grid manual lifts the handle for BACKWASH and lowers it for FILTER. Take automatic cleaners off first: the Hayward TracVac manual says to remove the cleaner before backwashing, and the Polaris 280 manual says to run filtration at least 5 minutes before reconnecting. Our how to vacuum a pool guide covers both cleaner types.
How do you backwash a DE filter?
The same way as sand, plus a fresh coat of DE. Hayward’s Pro-Grid manual: backwash about 2 minutes until the waste water looks clean, rinse 20 seconds, return to FILTER, then add new DE through the skimmer. Pentair FNS Plus filters take 3.6 to 6 lb, which works out to 1.0 lb per 10 sq ft of grid area; Hayward Pro-Grid filters take 1.25 lb per 10 sq ft.
- Set up the suctionPump off. Pentair’s FNS Plus guide opens the skimmer valve fully and closes the main drain line, so the fresh DE can go in through the skimmer afterward.
- BackwashValve to BACKWASH, air relief open, stand clear and start the pump; close the air relief at a steady stream and run until the discharge is clear, about 2 minutes on a Hayward Pro-Grid.
- RinseOn a Hayward six-position valve, RINSE for 20 seconds. Pentair’s FNS Plus sequence lists no timed rinse.
- Recoat with DEReturn to FILTER, mix the label amount of DE with water in a bucket and pour the slurry into the skimmer with the pump running (Pentair). Never run the filter more than 3 minutes without DE (Pentair); Hayward says a minute or two.
- Record the pre-coat pressureThe reading after recoating is the new clean pressure; the next backwash falls 8 to 10 psi above it (Hayward Pro-Grid).
A 48 sq ft filter therefore takes 4.8 lb of DE on Pentair’s rate and 6.0 lb on Hayward’s; Pentair’s Quad DE guide adds that a level 1-lb coffee can holds roughly half a pound. Our guide on how to clean a pool filter lists the DE charge for 11 Hayward and Pentair models and covers hand-cleaning the grids when a backwash no longer brings the pressure down.
How much water does backwashing use?
Flow times minutes. At the published backwash and rinse times, one cycle sends about 116 to 140 gallons to waste on a Hayward S244T at the code-minimum backwash rate, 221 to 347 gallons on a Pentair Triton TR60 and 224 gallons on a Hayward Pro-Grid DE4820. Hosing off a cartridge uses 20 to 30 gallons, according to Fort Worth Water.
| Filter and case | Flow used (gpm) | Flow basis | Backwash + rinse (minutes) | Gallons per cycle | Inches off a 15 x 30 ft pool (280.5 gal per inch) | Water cost at $8.54 per 1,000 gal |
|---|---|---|---|---|---|---|
| Hayward ProSeries S244T sand (3.1 sq ft) | 46.5 | MAHC minimum backwash rate, 15 gpm x 3.1 sq ft | 2.5 to 3 (2 backwash + 1/2 to 1 rinse) | 116 to 140 | 0.41 to 0.50 | $0.99 to $1.19 |
| Pentair Sand Dollar sand at 45 gpm | 45 | Hayward maximum flow for 1-1/2 in. pipe | 3.5 (3 backwash + 1/2 rinse) | 158 | 0.56 | $1.35 |
| Pentair Triton TR60 sand (3.1 sq ft) | 63 | Triton manual flow rate | 3.5 to 5.5 (3 to 5 backwash + 1/2 rinse) | 221 to 347 | 0.79 to 1.24 | $1.88 to $2.96 |
| Pentair Triton TR100 sand (4.9 sq ft) | 74 | Triton manual flow rate (15 gpm per sq ft) | 3.5 to 5.5 (3 to 5 backwash + 1/2 rinse) | 259 to 407 | 0.92 to 1.45 | $2.21 to $3.48 |
| Hayward Pro-Grid DE4820 (48 sq ft) | 96 | Pro-Grid design flow rate | 2.33 (2 backwash + 20 second rinse) | 224 | 0.80 | $1.91 |
| Cartridge hose-off (no backwash) | Fort Worth Water estimate | n/a | 20 to 30 | 0.07 to 0.11 | $0.17 to $0.26 |
Sources: flows and times from the Hayward ProSeries manual, Pentair Sand Dollar guide, Pentair Triton guide, Hayward Pro-Grid manual and CDC MAHC 2024 5.7.2.2.2; cartridge figure from Fort Worth Water; median rate from the PC&S pool evaporation research; PC&S arithmetic. Download CSV
Flows are maker or code figures, not measured flow at a given pool; actual backwash flow depends on the pump and plumbing.
Source: Source: PC&S arithmetic (gallons = gpm x minutes) from Hayward ProSeries and Pro-Grid manuals, Pentair Sand Dollar and Triton guides, CDC MAHC 2024 5.7.2.2.2 and Fort Worth Water. Accessed October 2026.. Download chart data (CSV)
The cost per cycle is small, $0.99 to $3.48 at the 25-city median of $8.54 per 1,000 gallons in our pool evaporation research, but the volume adds up: ten Triton TR60 cycles send 2,205 to 3,465 gallons out. EPA’s WaterSense pool guide cites a California Urban Water Conservation Council estimate that 23% of quantifiable pool water use goes to filter backwashes.
Why a code-minimum flow for the Hayward row? Hayward’s ProSeries manual gives backwash times but no backwash flow, so we used the 15 gpm per sq ft floor that the 2024 Model Aquatic Health Code (5.7.2.2.2) sets for public-pool sand filters: 46.5 gpm on a 3.1 sq ft bed. A pump that moves 63 gpm, Pentair’s rating for the same-size TR60, sends out more water in the same minutes.
Where can backwash water go?
Wherever your city allows, and that is rarely the street. Mesa sends it to your yard or the home’s sanitary sewer cleanout, Phoenix to landscaping and never the right-of-way, and Fairfax County to storm drains only once chlorine is under 0.1 mg/L. Backwash is dirty water: CDC found E. coli in 58% of 161 public-pool backwash samples in metro Atlanta in 2012.
| Place | Where backwash water may go | Source |
|---|---|---|
| Mesa, AZ | Your own yard, or the home sanitary sewer cleanout with no sand, sediment or debris; never toward a street manhole | City of Mesa |
| Phoenix, AZ | Reuse it on landscaping, away from salt-sensitive plants; backwash and saltwater pool water may not go to the street, alley or right-of-way | City of Phoenix |
| Fort Worth, TX | Follow Code Compliance guidelines; dechlorinate; not to the storm drain or wastewater system without city permission, never to a septic system | City of Fort Worth Water |
| Fairfax County, VA | To storm drains or streams only free of chlorine or bromine (under 0.1 mg/L), sediment and scum, at pH 6.0 to 8.0; otherwise small amounts to the sanitary sewer through a household drain | Fairfax County Public Works |
| San Diego County, CA | Never to the storm drain, including filter rinse water and media (DE, sand); rinse filters over landscaping | County of San Diego (June 2026) |
| Meadows Place, TX | Backwash plumbing to the sanitary sewer, not the street; DE never to surface waters, storm drains or septic; spent DE in the garbage | City of Meadows Place (2022) |
| Anywhere (federal guidance) | On a lawn or garden only if the water is not freshly chlorinated | U.S. EPA WaterSense (2022) |
Sources: City of Mesa; City of Phoenix; City of Fort Worth Water; Fairfax County Public Works; County of San Diego (June 5, 2026); City of Meadows Place (2022); U.S. EPA WaterSense (2022). Download CSV
Backwash carries what the filter caught: CDC’s metro-Atlanta study found E. coli in 93 of 161 public-pool backwash samples and Pseudomonas aeruginosa in 95 (59%), as our pool hygiene statistics report details. In Phoenix, our Phoenix pool builders page summarizes the city’s discharge permit for clean pool water.
How do you change the sand in a pool filter?
Drain the tank, take off the valve or closure, scoop out the old sand, check the laterals, then half-fill the tank with water and pour in the exact weight of No. 20 silica sand (0.45 to 0.55 mm) on your label. Finish with a backwash of at least 2 minutes and a rinse. Hayward ProSeries filters take 50 to 700 lb; Pentair Triton filters take 175 to 925 lb. Sand weights for 21 Hayward, Pentair, Jandy and Intex filters, the pea gravel option and silica dust precautions are in our guide on how to change sand in a pool filter.
- Power off and drainSwitch off the pump at the breaker, open the air relief valve and remove the drain cap at the base to empty the tank (Hayward).
- Remove the valveOn a top-mount filter, loosen the flange clamp and lift the multiport valve off the center pipe (Hayward ProSeries). Side-mount Triton filters open at the top closure.
- Dig out the old sandScoop or vacuum it out; Pentair’s Triton guide lists a Sand Vacuum (P/N 542090) for this. Keep the center pipe upright and covered so old sand does not drop into it.
- Inspect the underdrainLook for broken or loose laterals and replace them; Pentair lists a broken lateral as a cause of sand returning to the pool.
- Half-fill with waterWith the drain cap in and the laterals pointing down, fill the tank about 1/2 way with water to cushion the laterals from the falling sand (Hayward).
- Pour the label weightUse No. 20 silica at 0.45 to 0.55 mm with a uniformity coefficient of 1.75 or less (Pentair), in the weight on your nameplate. Cap the center pipe with the sand shield, keep it centered and leave at least 10 inches below the top on a ProSeries (Hayward).
- Refit the valveRemove the sand shield, check the valve O-ring, seat the valve on the center pipe and tighten the clamp.
- Backwash the new sandValve on BACKWASH, prime and start the pump, and run at least 2 minutes after the waste flow is steady to flush fine particles (Hayward; Pentair).
- Rinse, then filterRINSE until the sight glass is clear, about 1/2 to 1 minute (Hayward), then FILTER. Record the new clean pressure.
| Filter model | Filter bed area (sq ft) | Bed diameter implied by area (in.) | Tank width on maker drawing (in.) | No. 20 silica sand (lb) | 50 lb bags | Space above sand | Source |
|---|---|---|---|---|---|---|---|
| Hayward ProSeries S144T | 1.1 | 14.2 | Not listed | 50 | 1 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S166T | 1.4 | 16.0 | Not listed | 100 | 2 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S180T | 1.8 | 18.2 | Not listed | 150 | 3 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S210T | 2.2 | 20.1 | Not listed | 200 | 4 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S220T | 2.6 | 21.8 | Not listed | 250 | 5 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S244T | 3.1 | 23.8 | Not listed | 300 | 6 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S270T | 3.7 | 26.0 | Not listed | 350 | 7 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S310T2 | 4.9 | 30.0 | Not listed | 500 | 10 | At least 10 in. from the top | Hayward ProSeries manual |
| Hayward ProSeries S360T2 | 7.1 | 36.1 | Not listed | 700 | 14 | At least 10 in. from the top | Hayward ProSeries manual |
| Pentair Triton TR40 | 1.9 | 18.7 | 19.5 | 175 | 3.5 | 8.25 in. free board | Pentair Triton guide (2025) |
| Pentair Triton TR60 | 3.1 | 23.8 | 24.5 | 325 | 6.5 | 10.5 in. free board | Pentair Triton guide (2025) |
| Pentair Triton TR100 | 4.9 | 30.0 | 30.5 | 600 | 12 | 11.25 in. free board | Pentair Triton guide (2025) |
| Pentair Triton TR140 | 7.1 | 36.1 | 36.5 | 925 | 18.5 | 13.5 in. free board | Pentair Triton guide (2025) |
| Intex SF80110-2 (above-ground) | 0.79 | 12.0 | Not listed | 50 (or 35 lb glass sand) | 1 | Not listed | Intex owner manual |
| Intex SF70110-2 (above-ground) | 1.07 | 14.0 | Not listed | 77 (or 55 lb glass sand) | 1.5 | Not listed | Intex owner manual |
| Intex SF60110-2 (above-ground) | 1.44 | 16.2 | Not listed | 121 (or 84 lb glass sand) | 2.4 | Not listed | Intex owner manual |
Sources: Hayward ProSeries manual p. 11; Pentair Triton guide (2025) Tables 1 and 2 and p. 10 drawing; Intex SF owner manual; bag counts and implied diameters are PC&S arithmetic. Download CSV

At 3.1 sq ft the Triton TR60 takes 325 lb and the Hayward S244T 300 lb; at 7.1 sq ft the TR140 takes 925 lb and the S360T2 700 lb.
Source: Source: Hayward ProSeries owner's manual (IS210TS Rev A) specification table; Pentair Triton guide (2025) Table 2. Accessed October 2026.. Download chart data (CSV)
Same bed, different weight: at 3.1 sq ft the Pentair TR60 takes 325 lb and the Hayward S244T 300 lb, and at 7.1 sq ft the TR140 takes 925 lb against 700 lb for the S360T2, so load what your own label says. Intex’s above-ground sand filter pumps accept a wider 0.45 to 0.85 mm grade or lighter glass media: 50, 77 or 121 lb of silica, or 35, 55 or 84 lb of glass (Intex).
| Published by | Interval or rule | Type of source |
|---|---|---|
| HTH (sells pool filter sand) | Every 1.5 years for year-round pools, 3 years for seasonal pools | Product page |
| U.S. EPA WaterSense (Sept 2022) | Sand media lifetime 3 to 6 years; glass media 7 to 15 years | Federal guide citing 2010 and 2021 sources |
| Hayward (May 2023) | Roughly 5 years before the first sand change | Filter maker article |
| CDC MAHC 2024, 5.7.2.2.5 | Inspect sand for depth and cleanliness at least once a year; replace when needed (public pools) | Model code |
| Pentair Sand Dollar guide | No year count; chemically clean when pressure is 4 to 6 psi over start right after a backwash | Filter maker manual |
Sources: HTH Pool Filter Sand; EPA WaterSense (Sept 2022); Hayward (May 22, 2023); CDC MAHC 2024; Pentair Sand Dollar guide. Download CSV
How often should the sand be changed? Published intervals run from HTH’s 1.5 years for year-round pools to the top of EPA’s 3 to 6 year range, with Hayward at roughly 5 years. The steadier rule is a yearly look: the 2024 Model Aquatic Health Code (5.7.2.2.5) has public pools inspect sand depth and cleanliness at least once a year and replace it when needed. EPA lists glass media at 7 to 15 years. Sand, glass, cartridge and DE filters are compared on media life, water per cleaning and rated flow in our guide to pool filter types.
Should you backwash, chemically clean or change the sand?
Backwash at the pressure trigger, wait 24 hours after clarifier, chemically clean when pressure stays 4 to 6 psi over the clean start right after a backwash, and change the sand when a chemical clean does not bring the reading back or sand reaches the pool. The decision table and flowchart hold the same rules, each tied to its maker manual.
| If your situation is | Do this | Source |
|---|---|---|
| Gauge 8 to 10 psi over clean (Hayward) or 10 psi (Pentair) | Backwash until the sight glass runs clear, rinse, return to FILTER | Hayward ProSeries; Pentair |
| Flow meter shows a 30% drop, for example 60 to 40 gpm | Backwash | Pentair Triton guide |
| Clarifier went in less than 24 hours ago | Wait: HTH says not to backwash or clean the filter for at least 24 hours | HTH clarifier directions |
| New pool, first 48 hours | Backwash and clean the filter after 48 hours of running; start new plaster pools on FILTER, not BACKWASH | Pentair; Hayward ProSeries |
| Still 4 to 6 psi over start right after a backwash | Chemically clean the sand bed overnight (12 hours), then backwash | Pentair Sand Dollar guide |
| Sand surface crusted or caked, short filter cycles | Remove the top 1 inch of sand | Hayward ProSeries; Pentair |
| Sand coming back into the pool | Check for a broken lateral; reduce the backwash flow rate | Pentair sand filter guide |
| Bed still fouled after a chemical clean, or about 5 years on the sand | Change the sand: No. 20 silica, 0.45 to 0.55 mm, the weight on the label | Hayward; Pentair; EPA WaterSense |
| DE filter at 8 to 10 psi over pre-coat | Backwash about 2 minutes, rinse 20 seconds, recoat with 1.0 to 1.25 lb DE per 10 sq ft | Hayward Pro-Grid; Pentair FNS Plus |
| Cartridge filter | No backwash: pull and hose the cartridges | Pentair; Hayward SwimClear |
| Salt pool, or the street drain is the nearest outlet | Route backwash to your yard or sanitary cleanout as local rules allow; never to the street in Phoenix | City of Phoenix; City of Mesa |
Sources: Hayward ProSeries; Pentair Sand Dollar; Pentair Triton; HTH; EPA WaterSense; Hayward Pro-Grid; Pentair FNS Plus; Hayward SwimClear; City of Phoenix; City of Mesa. Download CSV

When should you call a pro? When sand keeps reaching the pool after you replaced the laterals, when water runs out of the waste line with the valve on FILTER, or when a cracked tank or valve body shows up during a sand change. Pool companies usually bill a filter cleaning outside the weekly fee: from $145 at Pearlin Pools in Brevard County, Florida, and $80 or $100 at two Arizona companies quoted by Thumbtack in August 2026; our pool service cost survey has the rest. A replacement 22 to 30 inch inground sand filter had a 2026 median list price of $689 in our pool equipment price index.
How we compiled this
In October 2026 we read 8 filter maker documents (Hayward ProSeries and Pro-Grid manuals and a Hayward filter-types article; Pentair Sand Dollar, Triton, FNS Plus and Quad DE guides; the Intex sand filter pump manual), 2 HTH product pages, CDC’s 2024 Model Aquatic Health Code, the EPA WaterSense pool guide and discharge rules from 6 local governments. Gallon, inch and cost figures are our arithmetic from those numbers; we did not measure flow at any pool or test any filter.
Frequently Asked Questions
What is the proper way to backwash a pool filter?
Pump off, valve to BACKWASH, pump on until the sight glass runs clear, pump off, valve to RINSE for 30 seconds to 1 minute, pump off, valve to FILTER. Hayward’s ProSeries manual gives about 2 minutes of backwash and Pentair’s Triton guide 3 to 5. Never move the handle with the pump running (Hayward; Pentair).
Do you backwash first or rinse?
Backwash first, then rinse. BACKWASH reverses flow to flush dirt out of the sand; RINSE runs water the normal way through the bed and out the waste port, which Pentair says resettles the bed and Hayward says keeps dirty backwash water from returning to the pool. Rinse 1/2 to 1 minute (Hayward) or about 30 seconds (Pentair).
How often are you supposed to backwash a pool filter?
When the gauge says, not on a calendar. Hayward backwashes at 8 to 10 psi over the clean reading and Pentair at 10 psi or a 30% flow drop. Pentair’s sand filter guides warn against backwashing on a timed basis such as every three days, because backwashing too often causes poor filtration (Pentair).
How long should you backwash a pool filter?
Until the sight glass or waste water runs clear. The manuals give about 2 minutes or less (Hayward ProSeries), about 3 minutes (Pentair Sand Dollar), 3 to 5 minutes (Pentair Triton) and about 2 minutes on a Hayward Pro-Grid DE filter, followed by a rinse of 20 seconds to 1 minute (Pentair Triton guide).
Do cartridge filters need to be backwashed?
No. Cartridge filters such as the Pentair Clean & Clear Plus and Hayward SwimClear are cleaned by pulling the cartridges and hosing them at about 10 psi (Pentair) or 7 to 10 psi (Hayward) over the starting pressure. Fort Worth Water says a hose-off uses 20 to 30 gallons against hundreds for a backwash.
How many bags of sand go in a pool filter?
Divide the weight on your filter label by the bag size. In 50 lb bags, a Hayward S244T (300 lb) takes 6 bags, a Pentair TR60 (325 lb) takes 6.5 and a Pentair TR140 (925 lb) takes 18.5. Buy No. 20 silica at 0.45 to 0.55 mm, the grade both Hayward and Pentair specify (Hayward).
Can you backwash a pool into the street?
Not in many cities. Phoenix prohibits backwash and saltwater pool water in the street, alley or right-of-way, Mesa sends it to your yard or sanitary sewer cleanout, and the County of San Diego bars it from storm drains. Fairfax County allows storm drains only once chlorine is under 0.1 mg/L and pH is 6.0 to 8.0.
Sources
- Hayward. ProSeries High Rate Sand Filters Owner Manual (IS210TS Rev A). Accessed 2026-10-26.
- Hayward. Pro-Grid Vertical DE Filter Owner Manual (ISDE2423EF Rev E). Accessed 2026-10-26.
- Hayward. SwimClear Cartridge Filter Owner Manual (ISC2031EF Rev B). Accessed 2026-10-26.
- Hayward. What are the Differences Between Filter Types? (May 22, 2023). Accessed 2026-10-26.
- Hayward. TracVac Suction Cleaner Owner Manual. Accessed 2026-10-19.
- Polaris (Zodiac). Polaris 280 Owner Manual (hosted by INYO Pools). Accessed 2026-10-19.
- Pentair. Sand Dollar and Cristal-Flo II Top Mount Sand Filter Installation and User Guide. Accessed 2026-10-26.
- Pentair. Triton Side Mount Sand Filter Installation and User Guide (2025). Accessed 2026-10-26.
- Pentair. FNS Plus Vertical Grid D.E. Filter Installation and User Guide (2025). Accessed 2026-10-26.
- Pentair. Quad D.E. Cartridge Style D.E. Filter Installation and User Guide. Accessed 2026-10-26.
- Pentair. Clean and Clear Plus Cartridge Filter: Cartridge Cleaning Guide. Accessed 2026-10-26.
- Intex. Krystal Clear Sand Filter Pump SF80110-2, SF70110-2, SF60110-2 Owner Manual (hosted by Home Depot). Accessed 2026-10-26.
- CDC. Model Aquatic Health Code, 5th Edition (2024), section 5.7.2. Accessed 2026-10-26.
- U.S. EPA. WaterSense: Making a Splash, Pool Water Efficiency (2022). Accessed 2026-10-26.
- HTH Pools. Why Is My Pool Cloudy? (clarifier directions). Accessed 2026-10-26.
- HTH Pools. HTH Pool Care Pool Filter Sand. Accessed 2026-10-26.
- City of Mesa, Arizona. Drain or Backwash Your Pool or Spa. Accessed 2026-10-26.
- City of Phoenix Water Services. Draining and Backwashing Your Pool. Accessed 2026-10-26.
- City of Fort Worth. Pools (Save Fort Worth Water). Accessed 2026-10-26.
- Fairfax County Public Works. Proper Discharge of Swimming Pool Water. Accessed 2026-10-26.
- County of San Diego. Pool, Spa, and Fountain Pollution Prevention Practices (June 5, 2026). Accessed 2026-10-26.
- City of Meadows Place, Texas. Only Rain Down the Storm Drain: Not Diatomaceous Earth (2022). Accessed 2026-10-26.
- CDC. Microbes in Pool Filter Backwash, Metro-Atlanta, 2012 (MMWR 2013;62(19)). Accessed 2026-10-08.
- Pearlin Pools. Pool Service Cost in Brevard County FL. Accessed 2026-10-08.
- Thumbtack. 2026 Pool Cleaning Costs (archived August 14, 2026). Accessed 2026-10-08.
- PC&S. Pool Equipment Prices 2026 (PC&S research). Accessed 2026-10-26.
- PC&S. Pool Evaporation Rate refill table (PC&S research). Accessed 2026-10-26.
- Royal Swimming Pools. How to Backwash a Pool Filter (claims checked). Accessed 2026-10-26.
- SwimmingPool.com. How to Change Sand in Your Pool Filter (claim checked). Accessed 2026-10-26.
- Inyo Pools. How To Change Sand in a Pool Sand Filter (claim checked). Accessed 2026-10-26.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.