Skip to content
Round above ground pool with a new blue liner and clear water on a summer morning
How-to guide: above ground pool liners

How to Install Above Ground Pool Liner: Overlap, Beaded and J-Hook Steps

How to install above ground pool liner: center the floor seam on the cove, fasten the top with coping, bead track or J-hook, vacuum out the air, then fill and cut fittings near the waterline.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓From 4 liner makers' sheetsBlue Wave, HII, GLI and Pureline instructions, with the measurement each step needs.
  • ✓A measuring guide that prevents reordersDiameter averaged 2 to 3 times, wall height from the track, flat or expandable.
  • ✓Where guides and makers disagreeCut fittings at 3 in below the opening or 2 ft of water, not at half full.
Quick answer
On a day above 70 F, spread 2 inches of sand and a 6 x 6 inch cove, center the liner’s wall seam on the cove, attach the top by type, vacuum the air from behind it, and smooth wrinkles at 1/2 inch of water. Cut the skimmer and return when water is 3 inches below each opening.
Above 70 F ideal, 60 F minimum
Hanging temperature
Water 3 in below each opening
Cut fittings
$250 to $800
Labor if hired

Key takeaways

  • Liner makers set the hanging temperature at above 60 F minimum (HII beaded instructions, 2022) to above 70 F ideal (Blue Wave); a SERP guide asks for 80 F.
  • Blue Wave, GLI and Pureline all say not to cut the skimmer or return until the water is 3 inches below each opening; HII says wait for at least 2 feet of water (HII vacuum-in sheet).
  • An overlap liner hangs about 2 inches over a 52 inch wall and 6 inches over a 48 inch wall in the Channel-Lok manual, so one overlap liner can fit both heights (Channel-Lok manual).
  • Measure the diameter inside wall to inside wall 2 to 3 times and average it, and measure wall height from the bottom track to the top of the wall (Pro Pools guide).
  • HomeAdvisor prices above-ground liners at $500 to $900 and installation labor at $250 to $800; beaded liners run $500 to $1,000 and overlap $200 to $600 (HomeAdvisor, 2026).

Overlap vs beaded vs J-hook: which above ground liner do you have?

Look at the top of the wall. Vinyl showing on the outside under the top rail means an overlap liner held by coping strips; a plastic track with no vinyl outside means a beaded liner; a hook profile sealed to the liner top is a J-hook or uni-bead, which can also go into a bead track once the hook is torn off about 7/8 inch above the bead.

Overlap, beaded and J-hook / uni-bead above ground liners compared
QuestionOverlapBeadedJ-hook / uni-beadSource
How the top attachesLiner drapes over the wall, held by plastic coping strips under the top railA bead snaps into a receiver track on top of the wallA J-shaped hook hangs on the wall top; tear it off and the bead fits a receiverBlue Wave; GLI; Pro Pools guide
How to tell what you haveVinyl visible on the outside of the wall under the railA plastic track along the wall top, no vinyl outsideHook profile sealed to the liner topPro Pools guide
Overhang or fitAbout 2 in over a 52 in wall, 6 in over a 48 in wall (Channel-Lok); about 4 in (Islamorada); 5 to 6 in (Pureline)Bead set at 12, 3, 6 and 9 o'clock firstHook over the wall; tear strip about 7/8 in above the beadChannel-Lok; Islamorada; Pureline; Blue Wave
Wall height choiceOne liner can fit 48 or 52 in wallsMust match the wall exactlyMust match the wallChannel-Lok; Pro Pools guide
Liner-only price, HomeAdvisor$200 to $600$500 to $1,000$400 to $900HomeAdvisor, 2026
Replacement easeTop rails come off to free itPro Pools calls it the preferred type for ease of replacementWorks on overlap or beaded poolsPro Pools guide; GLI

Sources: Blue Wave liner instructions; GLI liner instructions; Pureline instructions; Channel-Lok manual; Islamorada manual; Pro Pools guide; HomeAdvisor. Opened November 9, 2026. Download CSV

How each liner type fastens at the top of the wall: overlap over the wall under coping, beaded in a receiver track, J-hook on the wall edge. Drawn from the Blue Wave, GLI and Islamorada instructions.
How each liner type fastens at the top of the wall: overlap over the wall under coping, beaded in a receiver track, J-hook on the wall edge. Drawn from the Blue Wave, GLI and Islamorada instructions.

The overlap figure shows why overlap liners forgive a wrong wall height. Channel-Lok tells owners of a 52 inch pool to leave 2 inches of overhang and owners of a 48 inch pool to leave 6 inches with the same liner, a 4 inch difference that matches the wall difference. A beaded liner has no such slack: its bead must reach the receiver, so the wall height has to match.

Above ground pool liner prices by attachment type, and labor, 2026US dollars, liner only; labor separate
Above ground pool liner prices by attachment type, and labor, 2026Range chart: overlap liners $200 to $600, uni-bead $400 to $900, beaded $500 to $1,000, and above-ground installation labor $250 to $800.$0$250$500$750$1,000Overlap liner: $200 to $600Overlap linerJ-hook / uni-bead liner: $400 to $900J-hook / uni-bead linerBeaded liner: $500 to $1,000Beaded linerAbove-ground install labor: $250 to $800Above-ground install labor

Source: HomeAdvisor pool liner replacement cost (accessed November 9, 2026). Download chart data (CSV)

How do you measure an above ground pool for a new liner?

Record five things: shape, size, wall height, bottom type and attachment. Pro Pools measures a round pool inside wall to inside wall through the center 2 to 3 times and averages the readings, an oval at its longest inside length and widest inside width, and the wall from the bottom of the bottom track to the top of the wall.

Above ground pool liner measuring guide, with a worked 24 ft example
MeasurementHowExampleSource
ShapeRound or ovalRoundPro Pools guide
SizeInside wall to inside wall through the center, 2 to 3 times in different directions, then average; ovals: longest inside length and widest inside width23 ft 11 in, 24 ft 1 in and 24 ft 0 in average 24 ft 0 in: order a 24 ft roundPro Pools guide
Wall heightFrom the bottom of the bottom track to the top of the wall itself52 inPro Pools guide
Bottom typeFlat bottom, or expandable for a dug-out center; for expandable, measure depth from the liner top to the bottomFlatPro Pools guide; Doughboy (20 or 25 mil expandable)
AttachmentOverlap, beaded or J-hook / uni-beadOverlapPro Pools guide

Source: Pro Pools, Above ground pool liners: how to measure, replace, and get a wrinkle-free fit, opened November 9, 2026; expandable liner note from the Doughboy manual. The three readings are an illustrative example. Download CSV

Where to measure for a replacement liner: diameter inside wall to inside wall in 3 directions, wall height from the bottom track to the wall top (Pro Pools method).
Where to measure for a replacement liner: diameter inside wall to inside wall in 3 directions, wall height from the bottom track to the wall top (Pro Pools method).

Wall height is the measurement that most often goes wrong, according to Pro Pools, because 48, 52 and 54 inch walls all exist. A pool sold as 52 inch should measure 52 inches from the bottom of the track to the top of the steel; if you measure from the sand you lose the 2 inch base. Expandable liners are only for pools with a dug-out center, and Doughboy allows those only with 20 or 25 mil expandable liners.

How much vinyl a flat-bottom round liner contains, by size
Round poolFloor (sq ft)Wall, 48 in (sq ft)Wall, 52 in (sq ft)Total vinyl, 52 in wall (sq ft)Wall share of vinyl, 52 in
15 ft17718820438154%
18 ft25422624550049%
21 ft34626428663245%
24 ft45230232777942%
27 ft57333936894039%
30 ft707377408111537%

PC&S arithmetic: floor = 3.1416 x radius squared; wall = 3.1416 x diameter x wall height. Seams and overhang are not included. Download CSV

Vinyl in a round above ground pool liner, floor vs 52 in wallSquare feet, flat-bottom liner, before seams and overhang
Vinyl in a round above ground pool liner, floor vs 52 in wallStacked bars: a 15 ft liner has 177 sq ft of floor and 204 sq ft of wall; a 24 ft liner has 452 and 327; a 30 ft liner has 707 and 408.15 ft15 ft, Floor: 17715 ft, Wall (52 in): 20418 ft18 ft, Floor: 25418 ft, Wall (52 in): 24521 ft21 ft, Floor: 34621 ft, Wall (52 in): 28624 ft24 ft, Floor: 45224 ft, Wall (52 in): 32727 ft27 ft, Floor: 57327 ft, Wall (52 in): 36830 ft30 ft, Floor: 70730 ft, Wall (52 in): 408FloorWall (52 in)

Source: PC&S arithmetic from diameter and wall height (Pro Pools measuring method). Download chart data (CSV)

How to install an above ground pool liner, step by step

Pick a warm day, drain and strip the old liner, rebuild the 2 inch sand base and cove, unfold the new liner with the wall seam on the cove, fasten the top by type, refit the rails, vacuum out the air, smooth the floor at 1/2 inch of water, and cut the fittings near the waterline. Each step names the instruction sheet it comes from.

  1. Measure and orderDiameter averaged from 2 to 3 readings, wall height from the bottom track, flat or expandable, and attachment type (Pro Pools).
  2. Choose the dayAbove 70 F is ideal (Blue Wave) and 60 F the floor (HII). Sun the carton 2 to 3 hours (Pro Pools). Avoid wind, and have the new liner on site before draining (Doughboy).
  3. Drain and stripTurn off power, drain, remove faceplates, then top rails, stabilizer rails and coping to free the old liner (Pro Pools).
  4. Rebuild the baseClear grass 1 ft beyond the pool, spread 2 in of mason sand (not beach or play sand), form a 6 x 6 in cove, and tape over the wall bolts (Blue Wave). GLI and Pureline use an 8 x 8 in cove.
  5. Unfold and centerOpen the box without a knife. Center the wall-to-floor seam on the cove; on ovals run floor seams parallel to the straight sides. Keep the sidewall seam off the skimmer and return (HII).
  6. Fasten the topOverlap: drape it, clip coping on and leave it slack. Beaded: seat the bead at 12, 3, 6 and 9 o’clock, then work between (Blue Wave). J-hook: hook it over the wall edge.
  7. Refit rails and uprightsReinstall top rails and verticals before filling, so the wall stays rigid (HII beaded instructions).
  8. Vacuum out the airTape the skimmer cutout, feed a shop vac hose through the return, 4 to 6 in above the cove, and seal it (Channel-Lok, HII). Tug wrinkles out while it runs.
  9. Start the fillTape a sock over the hose end. At 1/2 to 3/4 in of water, drag soft-soled feet from the center out to clear floor wrinkles (HII).
  10. Stop the vacuumFollow your sheet: before 1 in of water (Channel-Lok), at 12 in (HII), or near the top (GLI, Pureline). Keep the hose above the water.
  11. Cut in the fittingsWhen water is 3 in below each opening (Blue Wave, GLI, Pureline), screw on the faceplate, then cut the vinyl inside it.
  12. FinishOverlap: trim the coping, roll the excess liner and tape it; do not cut it off (Channel-Lok). Fix the no-diving sticker 2 in above the water (Blue Wave).

New pool rather than a replacement? The full assembly order, with the wall, cove and track steps that come before the liner, is in our guide on how to set up an above ground pool. A liner swap skips those steps but not the base: Pro Pools tells owners to rebuild or smooth the cove every time, because a weak cove causes wrinkles at the wall-floor joint, and the new liner still needs its 2 inch sand floor.

When should you cut the skimmer and return holes in a new liner?

Late, at a point set by your instruction sheet. Blue Wave, GLI and Pureline say wait until the water is 3 inches below each opening; HII says at least 2 feet of water. Santorini cuts in with a few inches of water and Liner World waits until the pool is half full. Cutting early lets the vinyl stretch and tear away from the opening.

When to cut fittings and when to stop the vacuum: liner makers vs pool makers vs retail guides
SourceType of documentCut the skimmer and return whenTurn the vacuum off when
Blue Wave liner instructionsLiner makerWater is 3 in below each openingNot stated
GLI liner instructionsLiner makerWater reaches 3 in below each openingWater level nears the top
Pureline liner instructionsLiner makerWater reaches 3 in below each openingWater level nears the top
HII vacuum-in and beaded instructionsLiner and pool makerAt least 2 ft of water is in the poolAfter 12 in of water
Santorini pool manualPool makerWith a few inches of waterNot stated
Islamorada pool manualPool makerWater presses the liner firmly against the wallNot stated
Channel-Lok pool manualPool makerNot stated in the liner stepWhen most wrinkles are gone, before 1 in of water
Pro Pools guideRetailerWhen the liner is firmly set at the openingAbout 6 in of water
Liner World guide (Google top 3)RetailerWhen the pool is half fullWhen the pool is half full

Sources: Blue Wave; GLI; Pureline; HII vacuum-in and HII beaded instructions; Santorini, Islamorada and Channel-Lok pool manuals; Pro Pools; Liner World. All opened November 9, 2026. Download CSV

The reason is stretch. GLI and Pureline both warn that a faceplate installed too early can tear the liner away from the opening as the rising water stretches the vinyl. On a 52 inch wall, the 3 inch rule puts the skimmer cut near the top of the fill; HII’s 2 foot rule comes earlier but still after the floor and lower wall have seated.

The SERP guides drift from the sheets in two places. Liner World runs the shop vac until the pool is half full, while Channel-Lok removes the hose before the first inch of water and HII at 12 inches. And Liner World’s 80 F target is 10 degrees warmer than Blue Wave’s ideal and 20 above HII’s minimum. When the liner box and a blog disagree, the liner warranty follows the box: Blue Wave voids coverage when instructions are not followed.

Liner hanging temperature by source
SourceMinimum or ideal temperature for hanging a linerWarm-up advice
HII beaded liner instructionsAbove 60 F (16 C)Sunny day; sun warms and relaxes the vinyl
Blue Wave liner instructionsIdeal above 70 F (21.11 C)Spread the liner in the sun
Santorini pool manualAbove 70 FAssemble on a day above 70 F
Liner World guideIdeally 80 F or warmerHot, sunny day; fill only in daylight
Pro Pools guideWarm, sunny dayCarton in direct sun for 2 to 3 hours
Channel-Lok pool manualNot statedUnfold on the grass 1 to 2 hours before installing

Sources: HII; Blue Wave; Santorini; Liner World; Pro Pools; Channel-Lok. Download CSV

How does the shop-vac method set a liner without wrinkles?

It pulls the air out from behind the vinyl so the liner lies against the wall and floor before the water’s weight locks it in. Seal the skimmer cutout with tape, feed the hose through the return 4 to 6 inches above the cove so it does not suck sand, and adjust the liner with short tugs while the vacuum runs.

  • Hose position: through the return opening (HII, Channel-Lok) or the skimmer opening (GLI, Pureline, Blue Wave), sealed with duct tape or cardboard and masking tape.
  • Height: 4 to 6 inches above the sand cove, so the vacuum pulls air, not sand (Channel-Lok).
  • A household vacuum works if its filter bag is removed (GLI, Pureline). Check the hose end for sharp edges (HII).
  • If the liner will not shift, turn the vacuum off for a few minutes, adjust, then restart (GLI).
  • No pull at all usually means a vacuum leak at the seal (Pro Pools).
Fill with a sock taped over the hose end, as HII's instructions ask, and watch the liner at the top while the first 2 feet go in.
Fill with a sock taped over the hose end, as HII’s instructions ask, and watch the liner at the top while the first 2 feet go in.

Water depth decides how much you can still fix. Pro Pools says the floor can still be moved at 1/4 to 1/2 inch, wrinkles are still fixable at about 1 inch, and from several inches to about a foot the work gets harder. Doughboy draws the hard line: never lift the liner with more than 4 inches of water on the wrinkled area.

What goes underneath a pool liner?

Two inches of mason or brick sand over cleared, level ground, a cove at the foot of the wall, and optionally a floor pad. Blue Wave says not to use beach or play sand, which will not compact and leaves footprints, and to tape over the wall-joint screws so they cannot puncture the vinyl.

  • Sand: 2 in of mason sand (Blue Wave) or brick sand (GLI, Pureline), raked and hand-tamped.
  • Cove: 6 x 6 in in Blue Wave’s sheet and warranty; about 8 in high and 8 in wide in GLI’s and Pureline’s; preformed foam cove is accepted by all three.
  • Pad: Armor Shield floor padding instead of sand (GLI), or foam sheets 1 to 1-1/2 in thick joined with duct tape (Channel-Lok).
  • Ground: grass and roots removed 1 ft beyond the pool, since grass can grow through vinyl and that damage is not covered (Blue Wave).

Blue Wave’s notes put the structural point plainly: the liner is not a structural part of the pool, the wall and frame hold the water pressure, and a liner not supported by ground, cove and wall can blow out, which the warranty excludes. Both its 15-year and 25-year liner warranties also require a 6 inch cove where the wall meets the ground. The full base, with sand quantities for each pool size, is in our guide to leveling ground for an above ground pool.

Can you install a pool liner by yourself, and what does it cost?

With one helper, yes for most overlap and beaded liners: HII asks for at least one other person. For a 24 ft round with a 52 inch wall, DIY costs about $450 to $822 for the liner and refill water, against about $896 to $1,846 when a pro supplies and installs it, using HomeAdvisor’s 2026 ranges.

Replacing a 24 ft round, 52 inch wall above ground liner: DIY vs hired
Line item, 24 ft round, 52 in wallDIYHired outSource and date
Replacement liner$303.79 to $675.89 retail$500 to $900 liner (HomeAdvisor)Pro Pools, Doheny's, October 19, 2026; HomeAdvisor 2026
Installation labor$0$250 to $800HomeAdvisor 2026
Refill, 13,594 gal$146.14$146.14City of Akron; PC&S fill cost research, $10.75 per 1,000 gal
Total$449.93 to $822.03$896.14 to $1,846.14PC&S arithmetic

Sources: HomeAdvisor (accessed November 9, 2026); retail liner range from Pro Pools and Doheny’s as captured October 19, 2026 in our pool liner replacement cost guide; City of Akron gallons; PC&S fill cost research. Download CSV

Refill water is the same either way: 13,594 gallons at the $10.75 per 1,000 gallon median in our fill cost research is $146.14. Doughboy says to keep at least 12 inches of water in the pool when draining only to clean the liner, but a replacement means a full drain, so stage the new liner first. Imported liners also carry duty: U.S. Customs classified a 24 ft above-ground liner from China under HTS 9506.99.5500 at 5.3% plus 7.5% Section 301 duty (ruling N318201, March 25, 2021), as our pool equipment tariffs report details. Warranty terms, gauge versus mil and patch-or-replace thresholds are in our pool liner replacement cost guide. Drain times by pump and siphon, and five cities’ rules on where the water may go, are in our guide on how to drain an above ground pool.

Which liner fix fits your situation?

Match the liner to the wall top first, then let temperature and water depth set the timing. The table pairs each common situation with the action and the instruction sheet behind it, from a missing bead track to a spongy floor after the fill.

Above ground pool liner decision table
If your situation isDo thisWhy (source)
Vinyl shows on the outside of the wall under the top railOrder an overlap or a J-hook / uni-bead linerOverlap liners drape over the wall (Pro Pools guide)
There is a plastic bead track on the wall topOrder beaded, or a uni-bead with the J-hook torn off about 7/8 in above the beadBlue Wave unibead instructions
Forecast is below 60 FWaitHII beaded instructions: above 60 F
60 to 70 FSun the carton for 2 to 3 hours before hangingPro Pools; Blue Wave ideal is above 70 F
Wrinkles visible with 1/2 to 1 in of waterStop the hose and push them to the wall nowHII; Pro Pools
Wrinkles with more than 4 in of waterDo not lift the liner; drain back to a workable depthDoughboy; Pro Pools
The liner looks too shortPull the floor seam up off the ground and use a water bag; do not overstretchPureline; Blue Wave: overstretching voids the warranty
Floor feels spongy after the fillLook for water behind the liner before buying anotherPro Pools guide
Overlap liner on a level pool with 2 helpersDIY is realistic: labor would be $250 to $800HII: at least one other person; HomeAdvisor

Sources: Pro Pools; Blue Wave; HII; Doughboy; Pureline; HomeAdvisor. Download CSV

Above ground pool liner installation: the key numbers
NumberValueSource
Sand base under the liner2 in of mason or brick sandBlue Wave; GLI; Pureline
Cove6 x 6 in (Blue Wave) to 8 x 8 in (GLI, Pureline)Liner makers
Hanging temperatureAbove 60 F minimum (HII); above 70 F ideal (Blue Wave)Liner makers
Smooth the floor at1/2 to 3/4 in of waterHII; Blue Wave
Cut fittings at3 in below each opening (Blue Wave, GLI) or 2 ft of water (HII)Liner makers
Overlap overhang2 in on a 52 in wall, 6 in on a 48 in wallChannel-Lok
Vinyl in a 24 ft, 52 in liner779 sq ft (452 floor + 327 wall)PC&S arithmetic
Labor if hired$250 to $800HomeAdvisor

Sources: Blue Wave, GLI, Pureline, HII instructions; Channel-Lok manual; HomeAdvisor; PC&S arithmetic. Download CSV

Pool size sets the liner you order, and the above ground pool sizes guide lists every round from 12 to 33 ft and every oval with its gallons. For the cost of the whole pool, liner included, see the above ground pool cost guide; a full drain and refill also resets the water chemistry, covered in the pool chemical levels chart.

How we compiled this

We read 5 liner instruction sheets (Blue Wave, HII vacuum-in, HII beaded, GLI and Pureline), the liner sections of 4 pool manuals (Santorini, Islamorada, Channel-Lok, Doughboy), 2 retailer guides that rank for this search, and HomeAdvisor’s cost page, all opened in November 2026. Vinyl areas and totals are PC&S arithmetic; we did not install a liner, and videos and forum posts were not used as sources.

Frequently Asked Questions

How to properly install an above ground pool liner?

On a day above 70 F, spread 2 inches of sand and a 6 x 6 inch cove, center the wall seam on the cove, fasten the top by type, vacuum the air out, smooth wrinkles at 1/2 inch of water, and cut fittings when water is 3 inches below each opening (Blue Wave).

Can I install a pool liner by myself?

With a helper, yes: HII’s beaded instructions ask for at least one other person, and overlap liners are the easiest type to fit. Hiring out costs $250 to $800 in labor for an above ground liner (HomeAdvisor, 2026), plus $500 to $900 for the liner.

How much does it cost to put a liner in an above ground pool?

HomeAdvisor puts an above ground liner at $500 to $900 and installation at $250 to $800 (2026). Retail 24 ft round liners listed at $303.79 to $675.89 on October 19, 2026, and refilling 13,594 gallons costs about $146 at the $10.75 per 1,000 gallon median.

What goes underneath a pool liner?

Two inches of mason or brick sand, raked and tamped, with a cove of 6 x 6 inches (Blue Wave) to 8 x 8 inches (GLI) at the wall. Blue Wave rules out beach and play sand. Foam sheets 1 to 1-1/2 inches thick or a floor pad can replace sand (Channel-Lok, GLI).

Overlap vs beaded liner: which is better?

Overlap liners cost less, $200 to $600 against $500 to $1,000 for beaded (HomeAdvisor), and one overlap can fit 48 or 52 inch walls. Beaded liners need a bead receiver and an exact wall height, but Pro Pools calls them the easiest to replace later.

How do you install a J-hook liner?

Hang the J-hook over the top edge of the wall all the way round, refit the top rails, then fill as for an overlap liner. To use a uni-bead liner in a bead track instead, cut the tear strip about 7/8 inch above the bead and tear the hook off (Blue Wave).

Sources

  1. Blue Wave Products (hosted by Pro Pools). Above-ground pool liner installation instructions. Accessed 2026-11-09.
  2. HII (hosted by Pro Pools). Instructions for vacuuming in or kicking in pool liner. Accessed 2026-11-09.
  3. HII (hosted by Pro Pools). Beaded liner installation instructions 573-3550 (rev. 03/2022). Accessed 2026-11-09.
  4. GLI (hosted by Royal Swimming Pools). Above ground liner installation instructions (unibead). Accessed 2026-11-09.
  5. Pureline (Inyo Pools). Above ground pool liner installation instructions. Accessed 2026-11-09.
  6. Pro Pools. Above ground pool liners: how to measure, replace, and get a wrinkle-free fit. Accessed 2026-11-09.
  7. Liner World. Complete guide for installing your above ground pool liner. Accessed 2026-11-09.
  8. Santorini (hosted by The Home Depot). Santorini aboveground pool manual. Accessed 2026-11-09.
  9. Doughboy. Round pools assembly and installation instructions 573-3615. Accessed 2026-11-09.
  10. Pro Pools (host). Round above ground pool installation instructions (Islamorada). Accessed 2026-11-09.
  11. Atlantic Pools (hosted by Pool Supplies). Channel-Lok 1 oval pools manual. Accessed 2026-11-09.
  12. HomeAdvisor. Pool liner replacement cost. Accessed 2026-11-09.
  13. Pro Pools. 24 ft round above ground pool liners. Accessed 2026-10-19.
  14. Doheny's. Swimline beaded pool liner, 52 in wall, 24 ft round. Accessed 2026-10-19.
  15. City of Akron. How to calculate the gallons in a swimming pool. Accessed 2026-11-09.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.