Skip to content
Wet patch on a concrete pool equipment pad beside PVC pipes with a pool in the background
Pool equipment guide: repair

Pool Pump Leaking? Find the Leak, Fix It and What It Costs

Pool pump leaking? Water under the motor means a worn shaft seal ($19.95 to $29.95 DIY, $100 to $250 by a pro); drips at the lid, drain plugs or threads mean an O-ring or PTFE tape fix.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓A leak location mapSix leak points on one diagram, each tied to the cause and fix printed in Hayward, Pentair and Jandy manuals.
  • ✓Dated part pricesShaft seals, O-rings, drain plugs and housings by part number, listed November 9, 2026.
  • ✓Fix or replace thresholdsA decision table using pro repair ranges and DOE's 7-year pump life.
Quick answer
Dry the pump, run it for 5 minutes and watch where the first drop forms. Under the motor is the shaft seal; the lid, drain plugs and threaded ports are O-ring or PTFE tape fixes. Parts cost $5.95 to $33.90; a pro seal job $100 to $250 (Angi, Nov 2025).
$19.95 to $29.95
Shaft seal, DIY
$100 to $250
Shaft seal, pro
Hand tight + 1.5 turns, PTFE tape
Fitting rule

Key takeaways

  • Water dripping from under the motor is the shaft seal; Pentair calls it a wearable part that needs replacing after prolonged operation (Pentair IntelliFlo3 guide P/N 356231.F).
  • A shaft seal lists at $19.95 to $29.95 for Hayward Super Pump, Pentair SuperFlo and IntelliFlo3 pumps (ePoolSupply, Nov 9, 2026); a pro seal repair runs $100 to $250 (Angi, Nov 2025).
  • Hayward says all seal leaks should be replaced at once, because water reaching the bearings washes out the grease and makes them whine (Hayward Super Pump manual 1017836 Rev A).
  • Threaded ports get 1 to 2 layers of PTFE tape, hand tight plus 1.5 turns; Hayward warns pipe dope can crack the plastic (Hayward Super Pump manual 1017836 Rev A).
  • A pump that leaks only when it is off usually sits below pool level, so the lid O-ring, drain plugs and suction fittings are the suspects (Pentair 356292).
Key numbers for a leaking pool pump, with source
NumberWhat it meansSource
5 to 6 inVacuum a healthy Hayward pump pulls at the strainer cover with the suction blockedHayward 1017836 Rev A
10 yearsHayward: inspect seals and gaskets often and replace them at least this oftenHayward 1017836 Rev A
1 to 1.5 turnsPast hand tight on a threaded port with PTFE tape; no pipe dopeHayward 1017836 Rev A; IS0710X62 Rev B
$19.95 to $29.95Listed price of a shaft seal for Hayward Super Pump, Pentair SuperFlo or IntelliFlo3 (Nov 9, 2026)ePoolSupply
$100 to $250Professional shaft seal repairAngi, Nov 2025
7 yearsDOE mean life of a residential self-priming pool pumpU.S. DOE, 82 FR 5650
3,000+ gallonsWater a leak of one drip per second can waste in a yearEPA WaterSense

Sources: Hayward Super Pump manual 1017836 Rev A; Hayward IS0710X62 Rev B; ePoolSupply (Nov 9, 2026); Angi, Nov 2025; U.S. DOE, 82 FR 5650; EPA WaterSense. Download CSV

Where is your pool pump leaking? The leak location map

A pool pump leaks from six places: the lid O-ring, a threaded port or union, the drain plugs, the seam between housing and seal plate, the shaft seal under the motor, or a crack. Dry the pump with a towel, run it for 5 minutes and watch where the first drop forms; that spot names the part and the fix.

Leak location map: the six places a self-priming pool pump leaks, numbered to match the table below. Compiled from Hayward, Pentair and Jandy manuals accessed November 9, 2026; PC&S diagram, not to scale.
Leak location map: the six places a self-priming pool pump leaks, numbered to match the table below. Compiled from Hayward, Pentair and Jandy manuals accessed November 9, 2026; PC&S diagram, not to scale.
Pool pump leak location map: symptom, cause, maker's fix and listed part price
#Where the water showsUsually leaks whenLikely causeMaker's fixPart and listed price (Nov 9, 2026)Source
1Top of the strainer pot, around the lidPump off and below pool level; running it pulls air insteadDirty, dry, flattened or misseated lid O-ring; lid not lockedClean the O-ring, lube it (Hayward names Jack's 327), hand tighten the lid onlyLid O-ring $7.95 to $18.95; Jack's 327, 1 oz, $14.95Hayward 1017836 Rev A; Pentair 356231.F
2Threaded suction or discharge port, or a unionDischarge side drips while running; suction side pulls airOld or thin PTFE tape, overtightened or cracked threads, dirty union O-ringRemove, clean, rewrap with 1 to 2 more layers of PTFE tape, hand tight plus 1.5 turns; union O-rings hand tightPTFE tape; union O-ring by pump modelHayward 1017836 Rev A; Jandy H0315300 Rev U
3Drain plugs at the bottom of the pot or housingBoth, worst when off below pool levelMissing, flattened or hard plug O-ring or gasketReplace the plug or O-ring; Pentair says hand tighten onlyPlug with O-ring $5.95 to $9.95Pentair 356292; Hayward 1017836 Rev A
4Seam between the housing and the seal plateMostly while runningPinched or damaged seal plate O-ring or housing gasket, loose boltsCheck the O-ring is not pinched, tighten the bolts evenly, else disassembleSeal plate O-ring $7.95 to $12.49; Hayward SPX3200T housing O-ring $18.95Pentair 356231.F; Hayward IS3200XE Rev B
5Under the motor, at the pump to motor seamMostly while running; also when off below pool levelWorn or dry-run shaft sealReplace the two-part shaft seal; Jandy says have a qualified technician do itShaft seal $19.95 to $29.95; seal and O-ring kit $23.95 to $28.95Pentair 356231.F; Jandy H0315300 Rev U
6A crack in the pot or housingBothFreeze damage, pipe dope on plastic threads, overtighteningReplace the housing; freeze damage voids the Hayward warrantyHayward housing $264.95 to $309.95Hayward 1017836 Rev A

Sources: Hayward Super Pump manual 1017836 Rev A; Hayward IS3200XE Rev B; Pentair IntelliFlo3 guide P/N 356231.F; Pentair SuperFlo VS 356292; Jandy FloPro manual H0315300 Rev U; part prices from ePoolSupply, accessed November 9, 2026. Download CSV

Trace the water before you buy parts. Water runs downhill along the pump body, so a puddle under the motor can start at a fitting above it. Pentair’s IntelliFlo3 chart lists three leak rows, the strainer pot lid, the pot to seal plate joint and underneath the motor, each with its own fix (Pentair IntelliFlo3 guide P/N 356231.F, page 26).

Rows 1 to 3 are owner jobs that need an O-ring, a plug or PTFE tape costing $5.95 to $33.90. Rows 4 and 5 mean opening the pump. Row 6 means a new housing, which Hayward lists at $264.95 to $309.95 for its Super II, Super VS and TriStar bodies (ePoolSupply, Nov 9, 2026). If the pump will not run at all, our pool pump not working guide sorts the electrical faults.

Why is my pool pump leaking from underneath the motor?

A pool pump leaking from underneath the motor almost always has a failed shaft seal, the two-part spring and ceramic seal that stops water following the motor shaft. Jandy’s manual names a damaged or failed mechanical seal for water between the motor and pump body. Running the pump dry is the most common way to burn one.

Pentair's own troubleshooting chart gives three leak locations and a fix for each; the third row, underneath the motor, is the shaft seal. Pentair IntelliFlo3 VSF guide P/N 356231.F, page 26, accessed November 9, 2026; boxes added by PC&S.
Pentair’s own troubleshooting chart gives three leak locations and a fix for each; the third row, underneath the motor, is the shaft seal. Pentair IntelliFlo3 VSF guide P/N 356231.F, page 26, accessed November 9, 2026; boxes added by PC&S.

The shaft seal has a rotating half on the impeller hub and a stationary ceramic seat pressed into the seal plate. The polished faces ride on a film of water, which is why Hayward says water acts as a coolant and lubricant for the mechanical shaft seal and that running dry may damage seals, causing leakage, and voids the warranty (Hayward Super Pump manual 1017836 Rev A).

Pentair adds the most common trigger: if the pool level drops below the skimmer opening, the pump draws air, loses prime and runs dry. Its SuperFlo VS guide says to keep the water half way up the skimmer opening (Pentair 356292). Our how to prime a pool pump guide lists the priming steps and limits from 9 manuals.

Pentair's SuperFlo VS guide says to keep the pool water half way up the skimmer opening; below it, the pump draws air, runs dry and damages the shaft seal.
Pentair’s SuperFlo VS guide says to keep the pool water half way up the skimmer opening; below it, the pump draws air, runs dry and damages the shaft seal.

Do not wait. Hayward’s noisy pump section says a leaking seal lets water into the bearings, wiping out the grease and causing a whine, and that all seal leaks should be replaced at once (Hayward Super Pump manual 1017836 Rev A, page 11). Rust-colored streaks on the motor end bell are a sign the water has already reached the front bearing.

Why does a pool pump leak when it is off but not when it runs?

A pool pump that leaks only when off is almost always installed below the pool’s water level. With the motor stopped, pool water pushes on every seal, so a tired lid O-ring, drain plug or suction fitting weeps. While running, the strainer pot side is under suction, so the same flaw pulls air in instead and shows as bubbles at the returns.

When the pump leaks tells you which side of the pump the leak is on
What you seePump sits above pool water levelPump sits below pool water levelWhat it points to
Drips only while runningPressure side: discharge port, housing seam, shaft sealSameSeal or seam on the pressure side; check #2, #4, #5
Drips only when the pump is offRare: water drains back toward the poolPool water pushes on every seal when the pump stopsLid O-ring, drain plugs, suction fittings: #1, #2, #3
Bubbles at the pool returns, pump loses primeAir pulled in on the suction sideSame while runningLid O-ring or suction fitting leaking air, not water
Drips both on and offShaft seal or cracked housingShaft seal or cracked housing#5 or #6; dry the pump and watch where the first drop forms

Sources: Hayward Super Pump manual 1017836 Rev A (suction air leaks show as bubbles at the return fittings; 5 to 6 in of vacuum at the strainer cover); Pentair 356292 (pumps below water level). Download CSV

The strainer pot sits on the suction side. Hayward puts a healthy pump at 5 to 6 inches of vacuum at the strainer cover with the suction blocked, and says suction air leaks show as bubbles issuing from the return fittings (Hayward Super Pump manual 1017836 Rev A). So a lid leak while running looks like lost prime, not a puddle.

Pentair tells owners of pumps installed below the water level to close the return and suction valves before opening the strainer pot (Pentair 356292). Do the same before replacing a lid O-ring or drain plug on a flooded suction pump, or the pool will drain onto the pad.

How do you replace a pool pump shaft seal?

Pool pump shaft seal replacement takes the pump apart at the seal plate: cut power, drain the pot, unbolt the motor, unscrew the impeller, press out the ceramic seat, press in the new halves with clean faces, then reassemble to the maker’s torque. Hayward and Jandy reserve the job for qualified technicians; Pentair prints owner steps.

  1. Cut power and relieve pressureTurn off the breaker, open the filter air relief valve until the gauge reads 0 psi (Pentair 356231.F), and close the valves if the pump sits below pool level.
  2. Drain the pumpRemove both drain plugs from the strainer pot and keep the plug O-rings.
  3. Separate motor from housingHayward Super Pump: remove the four 3/8 in x 2 in housing cap screws and slide the motor out (1017836 Rev A).
  4. Remove the impeller and old sealHold the motor shaft, unscrew the impeller counterclockwise, note how the spring half sits, then tap the ceramic seat out of the seal plate.
  5. Clean and lube the recessUse the maker’s lubricant: soap solution for Hayward (no petroleum or silicone), silicone for Pentair SuperFlo VS, water for IntelliFlo3.
  6. Press in the new sealCeramic seat polished side out, spring half black graphite face away from the impeller. Wipe both faces with a clean cotton cloth; do not touch them.
  7. Reassemble to torquePentair SuperFlo VS seal plate to motor 75 to 80 in-lb; Hayward MaxFlo XE motor bolts 100 in-lb; TriStar XE housing bolts 185 in-lb, tightened alternately.
  8. Fill and testFill the pot to the suction port, start the pump and check the seam under the motor for 5 minutes before walking away.
Shaft seal rules by maker: the manuals disagree on lubricant
Maker ruleHaywardPentairJandy
Who should change the shaft sealOnly qualified personnel (Super Pump, PowerFlo manuals)Owner steps printed in the SuperFlo VS and IntelliFlo3 guidesA qualified service technician (FloPro H0315300)
Lubricant on the seal rubberDilute non-granulated liquid soap; no petroleum or silicone (PowerFlo ISSP1591)Silicone lubricant (SuperFlo VS 356292); water (IntelliFlo3 356231.F)Not stated in H0315300
Handling the seal facesScratches on the graphite and ceramic faces cause leaksScratched or marred faces will leak; clean before reassemblyNot stated
Bolt torque quotedTriStar XE housing bolts 185 in-lb; MaxFlo XE motor bolts 100 in-lbSuperFlo VS seal plate to motor 75 to 80 in-lbNot stated
ImpellerScrew onto the shaft clockwise, snugHand tighten clockwiseNot stated
Dry runningMay damage seals, causing leakage, and voids warrantySeal will be damaged and the pump will leakNot stated in leak section

Sources: Hayward Super Pump manual 1017836 Rev A; Hayward PowerFlo ISSP1591 Rev H; Hayward IS3200XE Rev B; Pentair SuperFlo VS 356292; Pentair IntelliFlo3 guide P/N 356231.F; Jandy FloPro manual H0315300 Rev U; accessed November 9, 2026. Download CSV

The makers do not agree on lubricant. Hayward’s PowerFlo manual says petroleum or silicone lubricants can contribute to seal leakage and calls for dilute liquid soap (ISSP1591 Rev H), while Pentair’s SuperFlo VS guide calls for silicone on the ceramic seat rubber. Follow the manual for your pump’s brand, not a generic video.

Pool pump shaft seal prices by pump model, November 2026Listed price of the maker-numbered shaft seal at one online retailer
Pool pump shaft seal prices by pump model, November 2026Bar chart: shaft seals list from $19.95 for the Hayward SPX1600Z2 to $34.95 for the Hayward SPX2700SAV Viton seal; the Pentair IntelliFlo3 seal is $29.95.Hayward Super Pump SPX1600Z2: $19.9Hayward Super Pump SPX1600Z2$19.9Pentair SuperFlo/Sta-Rite 17351-0101S: $21.9Pentair SuperFlo/Sta-Rite 17351-0101S$21.9Pentair SuperFlo 354545S: $24.9Pentair SuperFlo 354545S$24.9Hayward TriStar SPX3200SA: $24.9Hayward TriStar SPX3200SA$24.9Hayward Super VS Viton SPX1600Z2VIT: $24.9Hayward Super VS Viton SPX1600Z2VIT$24.9Pentair WhisperFlo 071734S: $26.9Pentair WhisperFlo 071734S$26.9Pentair IntelliFlo3 356210S: $29.9Pentair IntelliFlo3 356210S$29.9Hayward MaxFlo VS Viton SPX2700SAV: $35.0Hayward MaxFlo VS Viton SPX2700SAV$35.0

Source: ePoolSupply product listings, accessed November 9, 2026.. Download chart data (CSV)

Buy the seal by part number from the motor plate or manual parts list. Kits such as Aladdin’s GO-KIT line bundle the seal with the pot, plug and seal plate O-rings for $23.95 to $28.95 (ePoolSupply, Nov 9, 2026), and Pentair’s own IntelliFlo3 seal kit includes the drain plug O-rings.

How do you fix a leaking lid, drain plug or threaded fitting?

Lid, plug and fitting leaks are owner fixes. Clean and lube the lid O-ring and tighten the lid by hand only; replace a drain plug O-ring that is flat or hard; and rewrap a leaking threaded port with 1 to 2 extra layers of PTFE tape, hand tight plus 1.5 turns. Never use pipe dope on plastic pump threads.

  • Lid O-ring (row 1) Remove the lid, clean the O-ring and its groove, lube it with Jack’s 327 ($14.95 for 1 oz), and replace it if flattened or cracked ($7.95 to $18.95). Hand tighten only; Hayward allows no wrenches.
  • Drain plugs (row 3) Swap the plug or its O-ring ($5.95 to $9.95). Pentair says hand tighten only. Jandy: do not lose the O-rings when you winterize.
  • Threaded ports (row 2) Unscrew the adapter, clean off old tape, rewrap clockwise as you face the open end with 1 to 2 more layers, then hand tight plus 1.5 turns. Do not force past the molded thread stop.
  • Unions Jandy: loosen both union nuts, clean and reseat the union O-rings, then hand tighten the nuts.
  • Seal plate seam (row 4) Pentair: make sure the seal plate O-ring is not pinched and tighten the bolts joining pot and seal plate; if it still leaks, disassemble and inspect every O-ring.

Overtightening is the classic cause of a cracked port. Hayward’s manual notes that PTFE tape reduces friction considerably and that over-tightening can cause damage, which is why it caps the job at 1.5 turns past hand tight (Hayward Super Pump manual 1017836 Rev A). Older Hayward MaxFlo manuals allow 1 to 1.5 turns maximum (IS0710X62 Rev B).

A cracked pot or housing usually traces to winter. Hayward says allowing the pump to freeze with water in it voids the warranty (Hayward Super Pump manual 1017836 Rev A). The drain plug and storage steps are in our how to winterize a pool guide.

Freeze damage cracks pump housings; Hayward's manual says a pump allowed to freeze with water in it loses its warranty, so drain plugs come out before the first frost.
Freeze damage cracks pump housings; Hayward’s manual says a pump allowed to freeze with water in it loses its warranty, so drain plugs come out before the first frost.

How much does it cost to fix a leaking pool pump?

Fixing a leaking pool pump costs $5.95 to $33.90 in parts for a lid, plug or fitting leak and $19.95 to $29.95 for a DIY shaft seal (ePoolSupply, Nov 9, 2026). A pro seal repair runs $100 to $250 and bearings $150 to $350 (Angi, Nov 2025). A new variable speed pump installed costs $1,839 to $2,139.

Leaking pool pump repair cost: DIY parts vs professional price
Leak fixDIY parts (listed Nov 9, 2026)Pro priceSource
Lid O-ring plus lube$22.90 to $33.90Part plus about 1 hour at $75 to $150ePoolSupply; Angi hourly rate
Drain plug with O-ring$5.95 to $9.95Part plus about 1 hour at $75 to $150ePoolSupply; Angi
Seal plate or housing O-ring$7.95 to $18.95Part plus about 1 hour at $75 to $150ePoolSupply; Angi
Shaft seal$19.95 to $29.95$100 to $250ePoolSupply; Angi
Bearings after a long seal leakMotor shop job$150 to $350Angi
Motor after water damageVaries by motor$350 to $700Angi
Cracked strainer housing$264.95 to $309.95Part plus laborePoolSupply
New variable speed pump, installedNot a DIY figure$1,839 to $2,139PC&S pool pump replacement cost guide

Sources: ePoolSupply part listings, November 9, 2026; Angi, Nov 2025; PC&S pool pump replacement cost guide. Download CSV

What it costs to fix a leaking pool pump, by leak point (2026)DIY part prices listed November 9, 2026, and published pro repair ranges
What it costs to fix a leaking pool pump, by leak point (2026)Range chart: a drain plug costs $5.95 to $9.95, a shaft seal $19.95 to $29.95 DIY or $100 to $250 by a pro, bearings $150 to $350, a motor $350 to $700 and a new variable speed pump $1,839 to $2,139.$0$625$1,250$1,875$2,500Drain plug (DIY part): $6.0 to $9.9Drain plug (DIY part)Lid O-ring + lube (DIY): $22.9 to $33.9Lid O-ring + lube (DIY)Shaft seal (DIY part): $19.9 to $29.9Shaft seal (DIY part)Shaft seal (pro): $100 to $250Shaft seal (pro)Bearings (pro): $150 to $350Bearings (pro)Housing (DIY part): $265 to $310Housing (DIY part)Motor (pro): $350 to $700Motor (pro)New VS pump installed: $1,839 to $2,139New VS pump installed

Source: ePoolSupply listings (Nov 9, 2026); Angi pool pump repair cost (Nov 25, 2025); PC&S pool pump replacement cost guide.. Download chart data (CSV)

Worked example: a shaft seal leak fixed now vs left until the bearings whine
LineFix it now (DIY)Fix it now (pro)Ignore it until the bearings whine
Seal and O-ring kit$26.95In the pro price$26.95
Jack's 327 lube, 1 oz$14.95In the pro price$14.95
Labor$0, about an afternoon$100 to $250 all in (Angi)Bearings $150 to $350 (Angi)
Total$41.90$100 to $250$191.90 to $391.90
Worst caseMotor $350 to $700 (Angi) if water reaches the windings

Sources: ePoolSupply (GO-KIT92V $26.95; Jack’s 327 $14.95; Nov 9, 2026); Angi, Nov 2025. Download CSV

The cheapest leak is the one fixed early. A $26.95 seal kit plus $14.95 of lube totals $41.90; leaving the same leak until the bearings whine adds $150 to $350 for bearings (Angi, Nov 2025), or $350 to $700 for a motor. Retail pump prices by model are tracked in our pool equipment prices report.

Is it safe to keep running a leaking pool pump?

Run a leaking pool pump only if the drip is small, away from the motor’s electrical end and the pump still holds prime. Hayward’s start-up rule is blunt: if water leaks anywhere on the pump or filter, do not start it. A seal leak left running moves water toward the bearings and windings, and a drip of one per second wastes more than 3,000 gallons a year (EPA).

Water loss adds up quietly. EPA WaterSense says a leak of one drip per second can waste more than 3,000 gallons a year (EPA). What that refill costs in your city is in our cost to fill a pool study; if the pool level still drops after the pump is fixed, the leak is elsewhere and our pool leak detection guide takes over.

Should you repair the leak or replace the pool pump?

Repair the leak when it is an O-ring, plug, fitting or shaft seal on a quiet motor: parts run $5.95 to $29.95. Replace the pump when the housing is cracked and the motor is also tired, or when a single speed pump past DOE’s 7-year mean life leaks and whines. The decision table sets the thresholds.

Decision table: fix the leak, call a pro or replace the pool pump
If your situation isDo thisWhy (source)
Drip at the lid, a drain plug or one threaded portFix it yourself: clean, lube or replace the O-ring, rewrap PTFE tapeParts are $5.95 to $33.90 and Hayward and Pentair print the steps
Steady drip under the motor, motor quietReplace the shaft seal this week, DIY or proHayward: all seal leaks should be replaced at once
Drip under the motor and a screech or whineSeal plus bearings, or a motor; get a repair quoteHayward ties bearing whine to seal leaks that wash out grease
Visible crack in the pot or housingReplace the housing or the pumpA housing lists at $264.95 to $309.95; freeze damage voids the Hayward warranty
Single speed pump past 7 years with a seal leak plus motor noisePrice a variable speed replacementDOE mean life is 7 years; new VS pump installed $1,839 to $2,139
Water near the motor's electrical end or wiringShut the breaker off and call a technicianHayward: if leakage occurs, do not start the pump

Sources: Hayward Super Pump manual 1017836 Rev A; ePoolSupply (Nov 9, 2026); U.S. DOE, 82 FR 5650; PC&S pool pump replacement cost guide. Download CSV

If you replace, note that DOE efficiency standards for dedicated-purpose pool pumps apply to pumps made from July 19, 2021 (10 CFR 431.465), which in practice steers most inground filter pump buyers to variable speed. The model comparison and payback are in our variable speed pool pump guide, and the installed price breakdown is in the pool pump replacement cost guide.

How we compiled this

PC&S opened 8 manufacturer manuals from Hayward, Pentair and Jandy on November 9, 2026, and mapped every leak symptom, cause and fix they print into the 6-row leak location map. Part prices are retailer listings captured the same day; repair labor comes from Angi’s November 2025 cost guide. We did not test pumps or survey owners, and forum threads were used only for question wording.

Frequently Asked Questions

Why is my pool pump leaking from underneath?

Water under the pump is most often the shaft seal, which sits where the pump meets the motor. Pentair lists a leak from underneath the motor as a worn shaft seal, a wearable part (Pentair IntelliFlo3 guide P/N 356231.F). Check the drain plugs and the housing seam first, since water runs down the body; a seal lists at $19.95 to $29.95.

What's the average lifespan of a pool pump?

The U.S. Department of Energy used a mean life of 7 years for residential self-priming pool pumps in its 2017 efficiency rule (82 FR 5650). Seals and gaskets wear sooner: Hayward says to inspect them often and replace them at least every 10 years, or at once if damaged or leaking.

How much does it cost to fix a leaking pool pump?

Parts for a lid, plug or fitting leak cost $5.95 to $33.90, and a shaft seal $19.95 to $29.95 (ePoolSupply, Nov 9, 2026). A professional seal repair runs $100 to $250 and bearings $150 to $350 (Angi, Nov 2025). A new variable speed pump installed costs about $1,839 to $2,139.

How long will a water pump last once it starts leaking?

No maker publishes a number of days. Hayward says a seal leak lets water into the bearings, wiping out the grease and causing a whine, and that all seal leaks should be replaced at once (Hayward Super Pump manual 1017836 Rev A). Bearings run $150 to $350 to replace and a motor $350 to $700 (Angi), against a $19.95 to $29.95 seal.

Can I use silicone grease on a pool pump shaft seal?

Only if your pump’s maker says so. Pentair’s SuperFlo VS guide calls for silicone lubricant on the ceramic seat rubber, but Hayward’s PowerFlo manual says petroleum or silicone lubricants can contribute to seal leakage and specifies dilute liquid soap (ISSP1591 Rev H). Pentair’s IntelliFlo3 guide uses water.

Why does my pool pump leak only when it is off?

A pump that leaks only when off usually sits below the pool’s water level. With the motor stopped, pool water pushes on the lid O-ring, drain plugs and suction fittings; while running, the same side is under 5 to 6 inches of vacuum (Hayward), so it pulls air instead and the drip stops.

Sources

  1. Hayward. Super Pump Owner's Manual 1017836 Rev A. Accessed 2026-11-09.
  2. Hayward. PowerFlo Matrix/LX Owner's Manual ISSP1591 Rev H. Accessed 2026-11-09.
  3. Hayward. TriStar/MaxFlo/Super Pump XE Owner's Manual IS3200XE Rev B. Accessed 2026-11-09.
  4. Hayward. MaxFlo IS0710X62 Rev B. Accessed 2026-11-09.
  5. Pentair. IntelliFlo3 VSF Installation and Maintenance Guide P/N 356231.F. Accessed 2026-11-09.
  6. Pentair. SuperFlo VS / VST / SuperMax VS Installation and User's Guide P/N 356292. Accessed 2026-11-09.
  7. Pentair. SuperFlo Pump Installation and User's Guide P/N 356968. Accessed 2026-11-09.
  8. Jandy. FHP / FloPro pump manual H0315300 Rev U. Accessed 2026-11-09.
  9. ePoolSupply. Pump part listings: shaft seals, O-rings, drain plugs, housings, seal kits. Accessed 2026-11-09.
  10. Angi. How Much Does It Cost to Repair a Pool Pump? (Nov 25, 2025; Wayback capture). Accessed 2026-11-02.
  11. U.S. Department of Energy. Energy Conservation Standards for Dedicated-Purpose Pool Pumps, 82 FR 5650. Accessed 2026-10-03.
  12. U.S. EPA WaterSense. Fix a Leak Week. Accessed 2026-11-09.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.