Skip to content
Backyard hot tub on a cold autumn evening with the cover half open and faint steam
Hot tub care: troubleshooting

Hot Tub Not Heating: Normal Heat-Up Times, Error Codes and Fixes

Hot tub not heating usually means low flow, a tripped high limit, economy mode or lost power. A working 240 V tub gains 3 to 4 F an hour with the cover on; a 120 V tub about 1 F.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓Heat-up mathkW x 3,412 Btu / (gallons x 8.34): 4.1 F an hour for 400 gallons on a 4 kW heater, before losses.
  • ✓Codes from 7 manualsFLO, HL, OH, dr, OHH, FL-1, E2 and Jacuzzi codes 16 to 30, with what each maker says to do.
  • ✓Dated repair costsHeater repair $150 to $300 and replacement $200 to $700 (Fixr, Jan 2025); parts priced Nov 2026.
Quick answer
Reset the breaker or GFCI after 30 seconds with power off, then check the set point and economy or sleep mode. Next fix flow: fill to the line, clean the filter, purge any air lock. If a sensor or heater power code shows, or a 240 V tub gains under 3 F an hour, call a technician.
3 to 4 F per hour
Normal rate, 240 V
About 1 F per hour
Normal rate, 120 V
18 to 24 hours
Fresh fill to 100 F
$150 to $300
Heater repair

Key takeaways

  • Master Spas says its 240 V tubs heat about 3 to 4 F per hour with the cover on and 120 V models about 1 F per hour.
  • Hot Spring says a freshly filled tub reaches its preset 100 F within 18 to 24 hours, about 2 times the no-loss physics for a 400 gallon tub on 4 kW.
  • Flow is the first check in every manual we read: Hydropool shows FLO when no flow is detected and HL when the heater itself reaches 119 F.
  • On a 40 A service, Jacuzzi J-300 tubs heat only with jets pumps 1 and 2 off, and setting 104 F does not heat any faster.
  • Caldera and Hot Spring reset a tripped high limit by cutting power for 30 seconds; a GFCI that will not reset points to a ground fault.
  • Fixr (Jan 2025) puts heater repair at $150 to $300 and replacement at $200 to $700; a 5.5 kW heater listed at $231.98 in November 2026.

Is your hot tub heating slower than it should?

A 240 V hot tub should climb about 3 to 4 F an hour and a 120 V tub about 1 F, per Master Spas. Physics sets the ceiling: each gallon needs 8.34 Btu per degree, and 1 kW delivers 3,412 Btu an hour, so a 4 kW heater lifts 400 gallons about 4.1 F an hour before losses. A fresh fill takes 18 to 24 hours (Hot Spring).

What maker manuals and a state energy agency say about normal heat-up speed
SourceWhat it says about heating speedConditions
Master Spas Getaway manual (2025)About 3 to 4 F per hour on 240 V; about 1 F per hour on 120 VCover on; varies with tub size and air temperature
Hot Spring Highlife manual (2026)Reaches the preset 100 F within 18 to 24 hours after fillingCover on and locked
Hot Spring Hot Spot manual (2023)About 1,000 W of heat on 115 V and 4,000 W on 230 V; on a 15 or 20 A plug the heater runs only with the pump on low115 V or 230 V supply
Jacuzzi J-300 manual (2025)Setting 104 F does not heat faster; on a 40 A service the heater runs only with jets pumps 1 and 2 offNorth American 40 A wiring
Sundance 780 manual (2025)Heater restarts about 1 F below set point; Economy Mode heats only 5 PM to 7 AMFactory programming
California Energy Commission staff reportStart-up heat-up of a standard spa to 102 F took from 5 to more than 24 hoursTests of portable spas
PC&S physics, 400 gal tub4.1 F per hour at 4.0 kW; 1.0 F per hour at 1.0 kW, before losses8.34 lb per gal; 3,412 Btu per kWh

Sources: Master Spas Getaway 2025; Hot Spring Highlife 2026; Hot Spring Hot Spot manual; Jacuzzi J-300 2025; Sundance 780 2025; California Energy Commission staff report TN 222413; physics from EIA and Pentair. Download CSV

How fast a hot tub heats, by tub size and heater wattageDegrees F per hour with the cover on and no heat loss: kW x 3,412 Btu / (gallons x 8.34 lb)
How fast a hot tub heats, by tub size and heater wattageLine chart: a 400 gallon tub gains about 4.1 F per hour on a 4.0 kW heater, 5.6 F on 5.5 kW and 1.0 F on a 1.0 kW 120 V heater, before heat losses.02.557.5102503004005006001.0 kW (120 V plug-in), 250: 1.61.0 kW (120 V plug-in), 300: 1.41.0 kW (120 V plug-in), 400: 1.01.0 kW (120 V plug-in), 500: 0.821.0 kW (120 V plug-in), 600: 0.681.0 kW (120 V plug-in)1.375 kW (5.5 kW element on 120 V), 250: 2.21.375 kW (5.5 kW element on 120 V), 300: 1.91.375 kW (5.5 kW element on 120 V), 400: 1.41.375 kW (5.5 kW element on 120 V), 500: 1.11.375 kW (5.5 kW element on 120 V), 600: 0.941.375 kW (5.5 kW element on 120 V)4.0 kW (240 V), 250: 6.54.0 kW (240 V), 300: 5.54.0 kW (240 V), 400: 4.14.0 kW (240 V), 500: 3.34.0 kW (240 V), 600: 2.74.0 kW (240 V)5.5 kW (240 V), 250: 95.5 kW (240 V), 300: 7.55.5 kW (240 V), 400: 5.65.5 kW (240 V), 500: 4.55.5 kW (240 V), 600: 3.85.5 kW (240 V)

Real tubs heat slower: Master Spas measures 3 to 4 F per hour on 240 V and about 1 F per hour on 120 V with the cover on.

Source: PC&S arithmetic from EIA (1 Btu per lb per F; 3,412 Btu per kWh) and Pentair engineering data (8.34 lb per gallon). Download chart data (CSV)

Heat-up time by tub size and heater wattage, no heat loss (the best case)
Tub sizeHeaterDegrees F per hour (no losses)Hours to raise 4 F (100 to 104 F)Hours for a fresh fill, 60 to 100 F
250 gal1.0 kW (120 V plug-in)1.62.424.4
250 gal1.375 kW (5.5 kW element on 120 V)2.31.817.8
250 gal4.0 kW (240 V)6.50.66.1
250 gal5.5 kW (240 V)9.00.44.4
300 gal1.0 kW (120 V plug-in)1.42.929.3
300 gal1.375 kW (5.5 kW element on 120 V)1.92.121.3
300 gal4.0 kW (240 V)5.50.77.3
300 gal5.5 kW (240 V)7.50.55.3
400 gal1.0 kW (120 V plug-in)1.03.939.1
400 gal1.375 kW (5.5 kW element on 120 V)1.42.828.4
400 gal4.0 kW (240 V)4.11.09.8
400 gal5.5 kW (240 V)5.60.77.1
500 gal1.0 kW (120 V plug-in)0.84.948.9
500 gal1.375 kW (5.5 kW element on 120 V)1.13.635.6
500 gal4.0 kW (240 V)3.31.212.2
500 gal5.5 kW (240 V)4.50.98.9
600 gal1.0 kW (120 V plug-in)0.75.958.7
600 gal1.375 kW (5.5 kW element on 120 V)0.94.342.7
600 gal4.0 kW (240 V)2.71.514.7
600 gal5.5 kW (240 V)3.81.110.7

PC&S arithmetic: degrees per hour = kW x 3,412 / (gallons x 8.34), from EIA Btu definitions and Pentair engineering data. 1.375 kW is a 5.5 kW element run on 120 V per the VersaTherm BX5950AT listing. Download CSV

Worked example: why a 400 gallon fill takes 18 to 24 hours, not 10
StepArithmeticResult
1. Water weight, 400 gal400 x 8.343,336 lb
2. Heat for 1 F3,336 lb x 1 Btu3,336 Btu
3. 4.0 kW heater output4.0 x 3,41213,648 Btu per hour
4. Rate, no losses13,648 / 3,3364.1 F per hour
5. Fresh fill 60 to 100 F40 / 4.19.8 hours before losses
6. Hot Spring's real figure18 to 24 hoursAbout 1.8 to 2.5 times the no-loss time
7. A 5.5 kW element on 240 V should read240 x 240 / 5,500 (R = V squared / P)About 10.5 ohms; an open reading means a broken element

Inputs: EIA; Pentair; Hot Spring Highlife 2026. Element resistance from Ohm’s law (R = V squared / P). PC&S arithmetic. Download CSV

Use the table to decide whether your tub is broken or just slow. If a 400 gallon tub on 240 V gains 3 F in an hour with the cover locked, it is heating normally, since heat loss through the shell and cover eats part of the 4.1 F the element can deliver. If it gains under 1 F an hour on 240 V with a clean filter, the heater is not doing its job. Gallons by model are listed in our hot tub dimensions guide, and the electricity each degree costs is worked out in our hot tub temperature guide. For heat-up hours by gallons, heater kW and fill temperature, see our guide on how long it takes to heat a hot tub.

Why is my hot tub running but not heating?

When jets and lights work but the water stays cold, the manuals point to five causes: a low set point or low range, an economy or sleep mode, low-amp wiring that blocks the heater while jets run, a dirty filter that opens the pressure switch, and a tripped high limit. Hot Spring’s troubleshooting guide lists the integrated pressure switch first and says check for clogged filters.

Troubleshooting order compiled from 7 owner's manuals: power first, then codes, then settings, then heating speed. The decision table further down holds the same logic as text.
Troubleshooting order compiled from 7 owner’s manuals: power first, then codes, then settings, then heating speed. The decision table further down holds the same logic as text.
Hot tub heater not working: symptom table with causes, first fixes and when to call a tech
SymptomMost likely causes (manual)What to tryCall a tech when
No heat, no display, nothing runsTripped breaker or GFCI; blown fuse (Bullfrog 20 or 30 A)Power off at the disconnect, reset the breaker or GFCI after 30 seconds (Caldera)The GFCI trips again or will not reset: a ground fault (Hot Spring, Bullfrog)
Jets and lights work, no heatSet point or low range, economy or sleep mode, low-amp wiring, dirty filter, pressure switchRaise the set point, select high range, cancel economy mode, clean the filterFilter is clean and a flow code returns
Heats slowlyCover off or misaligned, cold air, 120 V heater, jets on high on a 15 or 20 A plugCover on and locked, jets off while heatingRate stays under 1 F per hour on 240 V with the cover on
Heats, then shuts offHigh-limit trip from low flow, air lock, hot fill water, blocked pump ventClean filter, purge the air lock, fill at 50 to 70 F (Hot Spring)High limit trips again after a clean filter and full water level
Display shows a flow code (FLO, FL, HFL, LF, E2)Low water, dirty filter, closed valves, air lock, failed pressure or flow switchWater to the fill line, clean filter, open jets and valves, purge airCode returns with a clean filter: switch or pump fault
Display shows a dry heater code (dr, dy, Code 27 or 28)Air in the heater or no water flowPrime the pumps; dr resets in 15 minutes (Bullfrog, Master Spas)Third dr or Heater Is Dry message
Display shows an overheat code (OH, OHH, HL, T-OH, H-OH)Water or heater hit its cutoff: 108 to 119 FStay out, cover off, let it cool; check flowAny overheat that repeats; any sensor code (Sn, SN, Prr, E5)

Sources: Hydropool Serenity 2024; Bullfrog 2018; Master Spas Getaway 2025; Sundance 780 2025; Jacuzzi J-300 2025; Hot Spring Highlife 2026; Caldera Paradise 2025. Accessed Nov 8, 2026. Download CSV

Low pH can be the slow cause behind repeat heater faults: Hot Spring says water below pH 7.0 is too acidic and can damage the heating system. Balance the water with the doses in our hot tub chemicals guide before blaming the element.

What do hot tub heater error codes mean?

Codes fall into four groups: flow (FLO, FL-1, HFL, LF, E2, Jacuzzi codes 16 and 17), dry heater (dr, Heater Is Dry, codes 27 and 28), overheat (OH, OHH, HL, T-OH, codes 29 and 30) and sensor or power faults (Prr, SN-1, E5, E6, code 80). Flow and dry codes are usually owner fixes; sensor and power codes need a technician.

Hot tub error codes related to heating, by maker manual, with meaning and fix as printed (Sundance shows its codes with a double dash, written here with one)
Code or messageMaker and manualMeaning (as printed)What the manual says to do
FLOHydropool Serenity (2024)No water flow detected while the primary pump runsAction not printed; use the flow steps below
HLHydropool Serenity (2024)Heater shut down: 119 F at the heaterAction not printed; check flow
OHHydropool Serenity (2024)Water in the spa reached 108 FAction not printed; stay out until it cools
PrrHydropool Serenity (2024)Problem with the temperature probeAction not printed; service call
HFLBullfrog (2018)Heater flow is reduced; heater retries after about 1 minuteFlow checks: water level, filter, valves, air, jets
LFBullfrog (2018)Not enough flow; heater disabledFix flow, then press any button
drBullfrog (2018); Master Spas Getaway (2025)Heater may be dry; spa shut down 15 minutes, retries up to 3 timesPrime pumps; press any button
Heater Is Dry (dy)Bullfrog (2018); Master Spas Getaway (2025)Repeated dr messages; flow restriction or air lockWill not reset itself; press any button after fixing flow
OHHBullfrog (2018)118 F detected in the heater; spa shut downReset when water is below 108 F
Overheat (water)Bullfrog (2018); Master Spas Getaway (2025)Water at 110 F; functions disabledAuto reset below 108 F (Bullfrog) or at 107 F (Master Spas)
HL (Heater Flow Fail)Master Spas Getaway (2025)Fifth Heater Flow Loss within 24 hours; heater disabledFix flow; press any button
ICEBullfrog (2018); Master Spas (2025); Sundance (2025)Possible freeze; equipment runsNo action; runs until 45 F (Master Spas) or 65 F (Sundance)
FL-1 / FL-2 / FL-3Sundance 780 (2025)Flow switch open, closed or erratic; dirty filter or air lock; heater offPower off, water level, clean filter, purge air lock with a hose for 30 seconds
SN-1 / SN-2Sundance 780 (2025)High-limit sensor or water sensor faultService call
T-OH / H-OHSundance 780 (2025)Water or high-limit sensor at 112 FStay out; cover off; economy mode; dealer
COOLSundance 780 (2025)Water 20 F below set point; heater runningNo action; common after a refill
Code 16 / Code 17Jacuzzi J-300 (2025)Heat low flow / failed flowFlow steps: power off, water level, filter, purge air lock
Code 27 / Code 28Jacuzzi J-300 (2025)Heater dry / heater may be dryPrime and restore flow
Code 29 / Code 30Jacuzzi J-300 (2025)Spa overheat / heater overheatDo not enter the water
Code 80Jacuzzi J-300 (2025)Heater authentication error; operation limitedDealer support
E2: NO FLOW-CHECK FILTERHot Spring Highlife (2026)Pressure switch: no flow; heater offClean filter; call if it repeats
E6: NO HEATER PWRHot Spring Highlife (2026)No power detected at the heaterService call
Power and Ready lights blinkingCaldera Paradise (2025)Dirty filter, low water, pressure switch or sensor problemDisconnect power 30 seconds; call if it continues

Sources: Hydropool Serenity 2024; Bullfrog 2018; Master Spas Getaway 2025; Sundance 780 2025; Jacuzzi J-300 2025; Hot Spring Highlife 2026; Caldera Paradise 2025. Accessed Nov 8, 2026. Download CSV

Temperatures differ by maker, so read your own manual’s number. Hydropool trips OH at 108 F water and HL at 119 F in the heater; Bullfrog and Master Spas cut off at 110 F water and 118 F in the heater; Sundance warns at 112 F. All 7 manuals print 104 F as the top normal setting, the limit CPSC sets for hot tub water, though Sundance adds an overtemp feature to 106 F.

How do you fix low flow and an air lock?

Turn the power off, bring the water above every jet and below the lowest pillow, clean the filter, then purge the air lock by running a garden hose into the filter wall fitting for 30 seconds. That is the Jacuzzi and Sundance procedure for flow codes, word for word in both 2025 manuals. Restore power and watch for the code to clear.

  1. Power off at the disconnectShut the breaker or GFCI disconnect before reaching into the filter well (Jacuzzi 15.1).
  2. Check the water levelWater must cover all jets but stay below the lowest pillow (Jacuzzi; Sundance); Hot Spring keeps it about 1.5 inches above the highest jet.
  3. Clean or swap the filterHose every pleat; the full routine is in our guide to cleaning a hot tub filter.
  4. Purge the air lockWith the cartridge out, seal a garden hose to the filter wall fitting with a rag and run water for 30 seconds (Jacuzzi; Sundance).
  5. Open jets and valvesBullfrog’s flow checks include closed valves, too many closed jets and pump prime.
  6. Restore power and primeRun the jets in short bursts of 5 to 10 seconds if the pump will not move water (Jacuzzi 15.3).
  7. Reset the codeBullfrog and Master Spas clear LF, dr and Heater Is Dry with any button once flow is back.
Check the real water temperature with a separate thermometer: CPSC says spa thermostats can err by as much as 4 degrees, and Jacuzzi's heater restarts only when water falls about 2 F below the set point.
Check the real water temperature with a separate thermometer: CPSC says spa thermostats can err by as much as 4 degrees, and Jacuzzi’s heater restarts only when water falls about 2 F below the set point.

Air locks are most common right after a refill, which is why Hot Spring and Caldera both say fill through the filter compartment. Hot Spring also says refill water should be 50 to 70 F, since a hot or near-freezing fill can trip the high limit. Our guide on how to drain a hot tub covers the refill steps. If the jets are also dead after a refill, our hot tub jets not working guide shows each maker’s airlock purge and its time limits.

How do I reset my hot tub heater?

Cut power at the breaker or GFCI disconnect for at least 30 seconds, then restore it. Caldera and Hot Spring say that resets a tripped high-limit thermostat; if the spa then runs, reduced flow caused the trip. Bullfrog, Master Spas and Jacuzzi panels clear most heater messages with any button press once the fault is fixed.

Wait the full 30 seconds: Caldera says resetting a GFCI sooner can make the Power indicator blink, which means repeating the test. If the high limit trips again with a clean filter and full water level, Caldera lists four other causes: blocked plumbing, a failed circulation pump, power left on while the tub was drained, and an air lock. Electrocution data behind these rules are in our pool and spa electrocution study.

Is an economy, sleep or low-amp setting stopping the heat?

Often. Sundance’s Economy Mode heats only from 5 PM to 7 AM, Bullfrog and Master Spas Sleep Mode holds water within 20 F of the set point, and Hot Spring’s Energy Saving Mode turns the heater off for up to 6 hours twice a day. Jacuzzi and Sundance both list economy mode in their three-step No Heat check.

Wiring can also hold the heater back. On a 40 A service, Jacuzzi says jets pumps 1 and 2 must be off for the heater to run, and on a 15 or 20 A plug the Hot Spring Hot Spot heater runs only with the pump on low. Running jets for an hour on those tubs adds no heat. Monthly costs of each supply option are in our hot tub electricity cost guide.

Keep the cover locked while heating: Jacuzzi and Sundance both list the cover in their No Heat steps, and Master Spas' 3 to 4 F per hour assumes the cover is on.
Keep the cover locked while heating: Jacuzzi and Sundance both list the cover in their No Heat steps, and Master Spas’ 3 to 4 F per hour assumes the cover is on.

Need a technician to look at the heater?

How do I know if the heating element in my hot tub is bad?

A bad element shows up as no heat with good flow, no flow or dry codes, and the set point above the water temperature. A technician confirms it with a meter, power off: a 5.5 kW element on 240 V should read about 10.5 ohms, and an open circuit means it has failed. Hot Spring’s E6 code reports no power at the heater.

Key numbers: hot tub heating
NumberValueSource
Heat for 1 F in one gallon8.34 BtuEIA (1 Btu per lb per F); Pentair (8.34 lb per gal)
Btu in 1 kWh3,412EIA
Normal rate, 240 V tub3 to 4 F per hourMaster Spas 2025
Normal rate, 120 V tubAbout 1 F per hourMaster Spas 2025
Fresh fill to 100 F18 to 24 hoursHot Spring 2026
Heater cutoff temperatures118 to 119 F at the heater; 108 to 112 F waterBullfrog, Master Spas, Hydropool, Sundance manuals
Wait before resetting power or GFCI30 secondsCaldera 2025; Hot Spring 2026
Typical heater repair$150 to $300Fixr, Jan 2025

Sources: EIA; Pentair; Master Spas 2025; Hot Spring 2026; Caldera 2025; manuals of Bullfrog, Hydropool and Sundance; Fixr. Download CSV

Other parts fail with the same symptom. A pressure switch that stays open keeps the heater off even with strong jets (Caldera), and a failed sensor shows SN-1 or SN-2 on a Sundance and Prr on a Hydropool. Ask the technician which part failed and for the measured reading, since a pressure switch listed at $69.76 costs far less than a heater at $231.98.

What does hot tub heater repair cost?

Fixr’s January 2025 ranges put a diagnostic visit at $100 to $200, heater repair at $150 to $300, heater replacement at $200 to $700 and circuit board replacement at $350 to $1,000. Parts priced on November 8, 2026 run $64.77 for a sensor, $69.76 for a pressure switch and $231.98 for a 5.5 kW heater with pressure switch.

Hot tub heater repair costs and part prices, dated
Repair or partCostSource and date
Diagnostic visit$100 to $200Fixr, updated Jan 31, 2025
Technician labor$75 to $125 per hourFixr, updated Jan 31, 2025
Heater repair$150 to $300Fixr, updated Jan 31, 2025
Heater replacement, installed$200 to $700Fixr, updated Jan 31, 2025
Pressure switch replacement$100 to $250Fixr, updated Jan 31, 2025
Thermostat replacement$125 to $250Fixr, updated Jan 31, 2025
Circuit board repair / replacement$150 to $450 / $350 to $1,000Fixr, updated Jan 31, 2025
Part: 5.5 kW heater with pressure switch (Master Spas)$231.98Master Spa Parts, Nov 8, 2026
Part: pressure switch assembly$69.76Master Spa Parts, Nov 8, 2026
Part: temperature and high-limit sensor (Master Spas, 12 inch)$64.77Master Spa Parts, Nov 8, 2026
Electricity for a fresh 400 gal fill, 60 to 100 FAbout 39.1 kWh, $7.10PC&S arithmetic at 18.16 cents per kWh (EIA, Aug 2026)

Sources: Fixr, Hot Tub Repair Cost (updated Jan 31, 2025); Master Spa Parts heater, pressure switch and sensor listings (Nov 8, 2026); EIA Electric Power Monthly (Aug 2026 price). Download CSV

Hot tub heating repair costs by jobInstalled cost range, US dollars
Hot tub heating repair costs by jobRange chart: diagnostic visits run $100 to $200, pressure switches $100 to $250, heater repair $150 to $300, heater replacement $200 to $700 and circuit board replacement $350 to $1,000.$0$250$500$750$1,000Diagnostic visit: $100 to $200Diagnostic visitPressure switch replacement: $100 to $250Pressure switch replacementThermostat replacement: $125 to $250Thermostat replacementHeater repair: $150 to $300Heater repairCircuit board repair: $150 to $450Circuit board repairHeater replacement: $200 to $700Heater replacementCircuit board replacement: $350 to $1,000Circuit board replacement

Fixr national ranges; parts alone listed at $64.77 to $231.98 on Master Spa Parts on Nov 8, 2026.

Source: Fixr, Hot Tub Repair Cost, updated Jan 31, 2025. Download chart data (CSV)

Warranty can cover the whole bill. Bullfrog’s limited warranty covers the heater for 5 years from purchase, and Watkins Wellness says its Caldera heater warranty applies even when water chemistry damage would void other coverage. Check the warranty card before paying for a diagnostic visit.

What should you do if your hot tub is not heating?

Work from power to flow to settings, and stop at the first code that says call for service. A blank panel is a breaker or GFCI issue; a flow or dry code is a filter, water level or air lock issue; a sensor, heater power or authentication code is a technician job. The decision table gives each case with its source.

Decision table: hot tub not heating, what to do in each situation
If your situation isDo thisWhy (source)
Nothing on the panel worksCheck the house breaker and the GFCI; reset after 30 secondsCaldera 2025; Bullfrog 2018
GFCI trips again right awayLeave it off and call a licensed electrician or spa techHot Spring 2026: a ground fault; Bullfrog: improper wiring or defective component
Panel works, water cold, no codeCheck set point, high or low range, economy, rest or sleep modeJacuzzi and Sundance No Heat steps; Bullfrog Spa will not heat
Plug-in 120 V tub heats only about 1 F per hourThat is normal; keep the cover on and jets off while heatingMaster Spas 2025; Hot Spring Hot Spot manual
Flow code or blinking lightsWater to the fill line, clean or replace the filter, purge the air lockJacuzzi 15.1; Sundance 14.1; Hot Spring E2
Overheat or high-limit code after a refillRefill at 50 to 70 F through the filter, let it cool, resetHot Spring 2026; Caldera 2025
Sensor, heater power or authentication codeBook a service callSundance SN codes; Hot Spring E5 and E6; Jacuzzi Code 80
Still under 1 F per hour on 240 V with a clean filter and cover onBook a service call: element, relay or pressure switchMaster Spas rate of 3 to 4 F per hour; Fixr repair ranges (Jan 2025)

Sources: Hydropool Serenity 2024; Bullfrog 2018; Master Spas Getaway 2025; Sundance 780 2025; Jacuzzi J-300 2025; Hot Spring Highlife 2026; Caldera Paradise 2025. Accessed Nov 8, 2026. Download CSV

Running the tub warmer while you troubleshoot is not a fix: CPSC warns thermostats can err by as much as 4 degrees, so check the water with a separate thermometer before anyone gets in. More routine checks are in our hot tub maintenance schedule.

How we compiled this

We read 7 owner’s manuals in November 2026 (Jacuzzi J-300 2025, Sundance 780 2025, Hot Spring Highlife 2026, Caldera Paradise 2025, Bullfrog 2018, Master Spas Getaway 2025, Hydropool Serenity 2024), Fixr’s repair cost page and three Master Spa Parts listings. Physics inputs (EIA, Pentair), the Hot Spring Hot Spot manual, a California Energy Commission report, the VersaTherm listing, CPSC and a Minnesota code handout were checked in October 2026 for sibling guides and reused. We did not repair or test any hot tub; forum posts were used only for question wording.

Frequently Asked Questions

Why is my hot tub running but not heating?

The usual causes are a dirty filter or air lock that opens the pressure switch, a tripped high limit, an economy or sleep mode, or low-amp wiring. On a 40 A service, Jacuzzi J-300 tubs heat only with jets pumps 1 and 2 off. Clean the filter, check the mode, then reset power for 30 seconds (Caldera, Hot Spring).

How do I reset my hot tub heater?

Turn the power off at the breaker or GFCI disconnect for at least 30 seconds, then turn it back on. Caldera and Hot Spring say this resets a tripped high-limit thermostat. On Bullfrog, Master Spas and Jacuzzi panels, most heater messages clear with any button once flow is fixed. A GFCI that trips again needs an electrician.

How do I know if my heating element is bad in my hot tub?

Suspect it when water stays cold with strong flow, no flow or dry codes, and the set point above the water temperature. A technician tests it with power off: a 5.5 kW element on 240 V should read about 10.5 ohms (240 squared divided by 5,500). An open reading means the element has failed.

How do I get the hot tub to heat up?

Lock the cover on, turn the jets off, raise the set point and cancel economy or sleep mode. Jacuzzi says setting 104 F does not heat faster. Expect about 3 to 4 F an hour on 240 V and about 1 F on 120 V (Master Spas), and 18 to 24 hours from a fresh fill (Hot Spring).

How long does it take to heat a hot tub?

About 18 to 24 hours from a fresh fill to 100 F (Hot Spring), and roughly an hour per 3 to 4 F afterward on 240 V. The physics ceiling for a 400 gallon tub is 4.1 F an hour on a 4 kW heater, 5.6 F on 5.5 kW and 1.0 F on a 1 kW 120 V heater, before heat loss.

Why is my hot tub not getting hot enough?

Check four things: the cover is on and latched, the tub is in high range rather than a 50 to 99 F low range (Bullfrog, Catalina), no economy schedule is active, and jets are off on a low-amp plug. CPSC says thermostats can err by up to 4 degrees, so confirm with a separate thermometer.

Sources

  1. Jacuzzi Hot Tubs. J-300 Collection Owner's Manual, Rev E (2025). Accessed 2026-11-08.
  2. Sundance Spas. 780 Series Owner's Manual, 2025 Rev A. Accessed 2026-11-08.
  3. Hot Spring Spas (Watkins Wellness). Highlife Collection Owner's Manual, 2026. Accessed 2026-11-08.
  4. Hot Spring Spas. Hot Spot Owner's Manual (Relay, Rhythm, Pace, Stride). Accessed 2026-10-27.
  5. Caldera Spas (Watkins Wellness). Paradise Series Owner's Manual, 2025. Accessed 2026-11-08.
  6. Bullfrog Spas. Owner's Manual, 2018 (rev 3.1.8). Accessed 2026-11-08.
  7. Master Spas. 2025 Getaway Spas Owner's Manual. Accessed 2026-11-08.
  8. Hydropool. Serenity Hot Tubs Owner's Manual, 2024. Accessed 2026-11-08.
  9. U.S. Energy Information Administration. Energy Explained: British thermal units. Accessed 2026-11-01.
  10. Pentair. Pool Product Catalog 2025-2026, Engineering Data. Accessed 2026-10-26.
  11. U.S. Energy Information Administration. Electric Power Monthly, Table 5.6.A. Accessed 2026-10-27.
  12. California Energy Commission. Final Staff Report TN 222413 (portable electric spas). Accessed 2026-10-27.
  13. Spa Depot (retailer). VersaTherm universal spa heater assembly BX5950AT. Accessed 2026-10-27.
  14. Fixr. Hot Tub Repair Cost (updated Jan 31, 2025). Accessed 2026-11-08.
  15. Master Spa Parts (retailer). 5.5 kW heater, pressure switch and sensor listings. Accessed 2026-11-08.
  16. U.S. Consumer Product Safety Commission. CPSC Warns of Hot Tub Temperatures. Accessed 2026-11-01.
  17. City of Farmington, Minnesota. Hot Tub/Spa Installation handout (2020 Minnesota State Building Code). Accessed 2026-10-26.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.