
How to Drain an Above Ground Pool: Methods, Drain Times and Where the Water Can Go
How to drain an above ground pool: dechlorinate below 0.1 mg/L, siphon or pump to your lawn or sewer cleanout under the local flow cap, and keep 12 inches of water in unless the liner is coming out.
- ✓Drain-time tableHours for 10 pool sizes by siphon, 20 to 30 gpm caps and a 1/4 HP pump.
- ✓Five city rulesAugusta, Louisville, Jefferson County MO, Southlake and Abilene, side by side.
- ✓Liner makers quotedSwimline, GLI, Blue Wave, LinerWorld and Doughboy on emptying a pool.
Key takeaways
- Pool water must test under 0.1 mg/L chlorine before it reaches a storm drain in Augusta, Georgia and Jefferson County, Missouri, and Abilene, Texas expects 5 to 10 days of sun without chlorine to get there.
- Sewer cleanout flow is capped at 20 gpm in Abilene and Jefferson County, 30 gpm by Louisville MSD and 50 gpm in Southlake, Texas, so a 30 gpm pump can break the rule in two of the five cities.
- Doughboy tells owners who drain to clean a liner to leave at least 12 inches of water in the pool, and Swimline, GLI and Blue Wave void shrinkage coverage on their liners if the pool is emptied.
- A 24 ft round pool with a 52 inch wall holds 13,594 gallons (City of Akron): about 8.7 hours with a 1/4 HP K2 UTA02502K pump at 5 ft of lift, against roughly 96.2 hours for one garden hose siphon (PC&S estimate).
- Frame pools are the exception: the Intex Metal Frame manual says to drain, dry and store the pool once temperatures drop below 41F.
Should you drain an above ground pool at all?
Only for a liner change, a frame pool going into storage or a move. Steel and resin wall pools are designed to stay full: Doughboy says leave at least 12 inches of water when draining to clean, and Swimline, GLI, Blue Wave and LinerWorld void some or all liner coverage if the pool is emptied. Chemistry problems usually need a partial drain, not an empty pool.
| Maker or document | What it says about emptying | Consequence named | Source |
|---|---|---|---|
| Swimline 25 and 30 season liner warranties | "The warranty is void against shrinkage if the pool is emptied" | No shrinkage coverage | Swimline warranty PDFs |
| GLI above ground liner standard warranty | "The warranty is void against shrinkage if pool is emptied" | No shrinkage coverage | GLI warranty card |
| Blue Wave liner instructions | "The warranty is void against shrinkage if the pool is emptied" | No shrinkage coverage | Blue Wave instructions |
| LinerWorld liner manual | Never completely drain unless changing the liner; warranty void if the water is emptied for any reason | Whole liner warranty | LinerWorld manual |
| Ocean Blue liner warranty sheet | Do not leave a liner with no water in the sun as vinyl will shrink; do not empty it in cold weather | Shrinkage | Ocean Blue |
| Doughboy round pool instructions | If you drain to clean the liner, leave at least 12 in of water measured up the metal sidewall | Warranty may be void | Doughboy |
| Backyard Leisure pool frame warranty | "Never allow your pool to stand empty"; leaving the pool empty voids the warranty | Frame and wall warranty | Backyard Leisure |
| Intex Metal Frame manual | Drain fully and store when air drops below 41F; dry the liner before folding | Ice damage, liner failure or collapse if left up | Intex 87PO manual |
Sources: Swimline 30 and 25 season warranties; GLI; Blue Wave; LinerWorld; Ocean Blue; Doughboy; Backyard Leisure; Intex. Accessed 2026-11-10. Download CSV

The reason is the vinyl. The Ocean Blue 15-year liner warranty sheet warns that a liner left with no water in the sun will shrink, and that a pool should not be emptied and left dry in cold weather either. A shrunken liner no longer reaches the cove and the top rail, so it has to be replaced. That is why LinerWorld tells owners never to drain completely unless the liner is being changed, and why our guide on how to install an above ground pool liner starts with a drained pool and a new liner already on site.
The wall is the second reason. Backyard Leisure says never to let a pool stand empty, and Atlantic warns that an empty pool can collapse in winter. Water weight holds the liner, the wall and the uprights in shape. If you are draining because of algae, high stabilizer or a leak hunt, plan a partial drain and keep at least 12 inches in, measured up the metal wall, as Doughboy specifies.
How to drain an above ground pool, step by step
Decide how far to drain, check where the water may go, stop chlorinating 5 to 10 days ahead and test under 0.1 mg/L, unplug the filter pump, then siphon or pump at or below your local flow limit. Keep at least 12 inches in unless the liner is coming out, finish the last inches with a cover pump or wet/dry vac, and refill the same day.
- Decide full or partialFull only for a liner change, storage or a move. Otherwise stop with at least 12 in of water measured up the metal wall (Doughboy).
- Check the discharge routeCall your city or sewer district. Lawn and sewer cleanout are the usual routes; septic systems are off limits in Abilene and Jefferson County, MO.
- Dechlorinate and testNo chlorine for 5 to 10 days in the sun (Abilene) or a dechlorinator, which Jefferson County says works in a day or two. Test for under 0.1 mg/L and pH 6 to 8.
- Pick the dayNot during or within 48 hours after rain (Louisville MSD), and 85F or cooler (Abilene). Overcast is kinder to vinyl (Ocean Blue).
- Unplug the filter pumpPull the plug rather than switching it off, because timers can restart it and run it dry (SwimmingPool.com). Abilene says never drain with the pool pump.
- Start the flowFrame pool: screw the drain connector and garden hose onto the drain valve (Intex). Other pools: siphon with a garden hose or set a submersible pump on the floor.
- Hold the flow under the cap20 gpm in Abilene and Jefferson County, 30 gpm in Louisville, 50 gpm in Southlake. A K2 UTA02502K moves 26 gpm at 5 ft of lift.
- Stop at your target12 in for a cleaning drain. For a liner change keep going: the K2 pump shuts off at 1/4 in, a Cover Care Model 300 reaches 1/8 in, and a wet/dry vac takes the rest.
- Refill the same dayThe Pool Factory advises removal and refilling in one day. Refill time and water cost are in our fill guide.

Frame pools drain differently. The Intex Metal Frame manual has you check that the inside drain plug is in place, remove the outside cap, attach a garden hose to the drain connector and push the connector onto the valve, which opens the plug and starts the flow. When the water stops, lift the wall opposite the drain to lead the last water out, then dry the liner in the sun and store it between 32F and 104F.
Refilling is where the bill lands. At the October 2026 median of $10.75 per 1,000 gallons in our cost to fill a pool ledger, refilling a 24 ft round costs about $146.14. Hose times by pool size are in our guide to how long it takes to fill a pool.
Siphon, drain valve or pump: which drain method should you use?
Use the pump if time matters and your sewer cap allows it, the siphon if you have no power or a 20 gpm limit, and the drain valve if your frame pool has one. A 1/4 HP K2 pump moves 1,550 gallons an hour at 5 ft of lift; a 50 ft, 5/8 inch hose siphon starts near 4.7 gpm and slows as the water drops.
| Method | Pools it suits | Flow | Lowest level it reaches | Source |
|---|---|---|---|---|
| Drain valve plus garden hose | Intex and other frame or soft-sided pools with a drain valve | Gravity, falls as the level drops | Until water stops, then lift the wall opposite the drain | Intex Metal Frame manual |
| Garden hose siphon | Any pool; no power needed | About 4.7 gpm at the start for 50 ft of 5/8 in hose, falling to 0 | Stops at the height of the hose outlet | Hoselink; Milwaukee Valve; PC&S estimate |
| Submersible utility pump | Steel, resin or frame pools when time matters | 1,800 GPH at 0 ft lift, 1,550 GPH at 5 ft (K2 UTA02502K) | Switches off at 1/4 in; continuous duty needs 6 in of water | K2 spec sheet |
| Pool cover pump | The last inches on the floor | 300 GPH (Cover Care Model 300) | Down to 1/8 in | PoolWeb listing, $89.71 on Nov 9, 2026 |
| Wet/dry vacuum | The final puddle | Tank size | Floor dry | SwimmingPool.com (POOLCORP) |
Sources: Intex Metal Frame manual; Hoselink; Milwaukee Valve; K2 UTA02502K spec sheet; PoolWeb cover pump listings (Nov 9, 2026); SwimmingPool.com. Download CSV
How do I get water out of my pool without a pump? Siphon it. Fill a garden hose with pool water, keep one end under the surface and run the other end down to the lawn or cleanout. Water flows only while the outlet sits below the pool’s water surface, so a hose that ends at ground level stops working near the pool floor of an above ground pool. Running the outlet 3 ft downhill keeps it flowing to the bottom and cuts the time by more than half.

The siphon numbers are our estimate, not a test. Hoselink lists 24 gpm through 50 ft of 5/8 inch hose at 45 psi. A siphon from 4 ft of water has only 1.73 psi to push with, at 0.433 psi per foot of head (Milwaukee Valve), and hose flow scales with the square root of pressure, so the start rate is about 4.7 gpm. Kinks, a 1/2 inch hose or a longer run will slow it further. Several hoses at once divide the time.
How long does it take to drain an above ground pool?
From about 1.9 hours for a 12 ft round at 30 gpm to about 182 hours for a 33 ft round with one hose siphoning to ground level. Divide gallons by gallons per minute, then by 60. A 24 ft round with a 52 inch wall holds 13,594 gallons: 11.3 hours at a 20 gpm sewer cap, 8.7 hours with a 1/4 HP pump.
| Pool (52 in wall) | Gallons (City of Akron) | Hose siphon to ground level, about 4.7 gpm falling to 0 (hours, PC&S estimate) | Hose siphon to 3 ft below pool floor (hours, PC&S estimate) | 20 gpm, Abilene and Jefferson County sewer cap (hours) | 26 gpm, 1/4 HP K2 pump at 5 ft lift (hours) | 30 gpm, Louisville MSD cap (hours) |
|---|---|---|---|---|---|---|
| 12 ft round | 3,398 | 24.1 | 11.0 | 2.8 | 2.2 | 1.9 |
| 15 ft round | 5,310 | 37.6 | 17.2 | 4.4 | 3.4 | 3.0 |
| 18 ft round | 8,602 | 60.9 | 27.8 | 7.2 | 5.5 | 4.8 |
| 21 ft round | 10,408 | 73.7 | 33.7 | 8.7 | 6.7 | 5.8 |
| 24 ft round | 13,594 | 96.2 | 44.0 | 11.3 | 8.7 | 7.6 |
| 27 ft round | 17,205 | 121.8 | 55.6 | 14.3 | 11.0 | 9.6 |
| 30 ft round | 21,240 | 150.4 | 68.7 | 17.7 | 13.6 | 11.8 |
| 33 ft round | 25,700 | 181.9 | 83.1 | 21.4 | 16.5 | 14.3 |
| 15 x 30 ft oval | 10,620 | 75.2 | 34.3 | 8.8 | 6.8 | 5.9 |
| 16 x 32 ft oval | 12,084 | 85.5 | 39.1 | 10.1 | 7.7 | 6.7 |
Sources: gallons from the City of Akron table; rates from Abilene, Jefferson County, Louisville MSD, the K2 UTA02502K spec sheet and Hoselink; PC&S arithmetic, November 2026. Download CSV
Source: City of Akron; Hoselink; Milwaukee Valve; K2 UTA02502K spec; Abilene and Louisville MSD caps; PC&S arithmetic. Download chart data (CSV)
| Step | Value | How it is worked out | Source |
|---|---|---|---|
| Gallons in a 24 ft round, 52 in wall | 13,594 | City of Akron table (48 in of water) | City of Akron |
| Water depth | 4 ft | 48 in of water / 12 | City of Akron |
| Siphon driving pressure at the start | 1.73 psi | 4 ft x 0.433 psi per ft of water | Milwaukee Valve |
| Siphon flow at the start, 50 ft of 5/8 in hose | 4.7 gpm | 24 gpm x square root of (1.73 / 45) | Hoselink (24 gpm at 45 psi); PC&S estimate |
| Siphon time, outlet level with the pool floor | 96.2 hours | 2 x 13,594 / 4.7 / 60 (flow falls as the level drops) | PC&S estimate |
| Same with 3 hoses siphoning | 32.1 hours | 96.2 / 3 | PC&S estimate |
| 1/4 HP K2 UTA02502K at 5 ft lift | 8.7 hours | 13,594 / 26 gpm / 60 | K2 spec sheet (1,550 GPH at 5 ft) |
| Water to refill at the 25-city median rate | $146.14 | 13,594 x $10.75 per 1,000 gal | PC&S cost to fill a pool ledger, October 2026 |
Sources: City of Akron; Milwaukee Valve; Hoselink; K2 spec sheet; PC&S cost to fill a pool ledger. Download CSV
Gallons come from the City of Akron table, which puts 48 inches of water in a 52 inch wall. A 48 inch wall holds about 12.5% less: 11,895 gallons for a 24 ft round. If your pool is not a stock size, measure it with the pool volume calculator, and see our above ground pool sizes chart for every round and oval.
Where can you drain above ground pool water?
Onto your own lawn or into a sanitary sewer cleanout in all five cities reviewed, once chlorine tests under 0.1 mg/L and pH sits between 6 and 8. Storm drains are a last resort or off limits. Flow caps run from 12 to 15 gpm in Augusta to 50 gpm in Southlake, and Abilene and Jefferson County ban septic systems.
| Jurisdiction | Chlorine before discharge | pH | Wait or dechlorination | Flow limit | Allowed routes | Rule cited |
|---|---|---|---|---|---|---|
| Augusta, GA | Under 0.1 mg/L for the storm sewer | Not stated | Dechlorination tablets or solutions | 12 to 15 gpm or less to avoid sewer backups | Sewer cleanout on your property (untreated allowed, owner liable for backups); storm sewer only once dechlorinated; never a manhole | Augusta Stormwater Management Ordinance 5-1-8 |
| Louisville MSD, KY | Essentially chlorine free, about 0.1 ppm total chlorine | 6 to 8 | At least 10 days after chemical treatment; not during or within 48 hours after rain | No more than 30 gpm | Grassy area large enough to absorb it, or a sanitary sewer cleanout | MSD guidance, Sept 3, 2024 |
| Jefferson County, MO | Under 0.1 mg/L | 6 to 8 | 10 days of sun, or chemical dechlorinators in a day or two | No more than 20 gpm to the sanitary sewer | Sanitary sewer (call the sewer district first) or your lawn; storm drain only if nothing else is possible; never a septic system | Federal Clean Water Act, county stormwater division |
| Southlake, TX | Under 0.1 ppm for the lawn; under 3 ppm for the sewer | 6 to 8 | About 10 days of sun, or dechlorinating chemicals | 50 gpm into the sewer cleanout | Lawn, or sanitary sewer cleanout after calling Public Works | Code of Ordinances Chapter 9.5, Article IX |
| Abilene, TX | Completely dechlorinated | 6 to 9 for the storm drain | 5 to 10 days of sun, or a chlorine neutralizer | 20 gpm or less by siphon or sump pump to the sewer | Lawn, sewer cleanout or indoor drain; storm drain only if neither is possible; never a septic system | City of Abilene ordinances |
Sources: Augusta Engineering Department; Louisville MSD; Jefferson County Stormwater; City of Southlake; City of Abilene. Accessed 2026-11-10. Download CSV
Source: Augusta; Abilene; Jefferson County MO; Louisville MSD; Southlake; accessed 2026-11-10. Download chart data (CSV)
Chlorine is the reason for the rules. Louisville MSD says the average pool carries 10 times more chlorine than some aquatic life can withstand, which is why storm drains that run to creeks are the last option everywhere above. Augusta cites its Stormwater Management Ordinance, section 5-1-8, and makes the owner liable for any sewer backup a drain causes. Rules for Mansfield, Fairfax County, Washington DC, Montgomery County and Ohio are in our guide on how to drain a pool.

How can I drain water around my above ground pool? Point the outlet downhill and away from the pool base, the house and the neighbors. Southlake allows the lawn route only below 0.1 ppm chlorine and wants the lawn free of pet waste and fertilizer because the water filters through it, and Jefferson County says to drain slowly so it soaks in without ponding or erosion. Water left standing against the wall softens the sand base the pool sits on.
Drain fully, partially or not at all?
Drain fully only for a liner swap, frame pool storage below 41F or a move. Drain partially, keeping 12 inches in, for cleaning or a chemistry reset. Do not drain a steel wall pool for winter, after rain within 48 hours, on a day above 85F or into a septic system. The table sets each threshold and its source.
| If your situation is | Do this | Why (source) |
|---|---|---|
| Replacing the liner | Drain fully, with the new liner on site, on a calm day | Doughboy: never leave the pool standing without a liner; do not install on a windy day |
| Cleaning, a leak hunt or a chemistry reset on a steel or resin wall pool | Partial drain only: leave at least 12 in of water | Doughboy warns the warranty may be void otherwise; Swimline, GLI and Blue Wave void shrinkage cover if emptied |
| Frame pool and nights will drop below 41F | Drain fully, dry the liner, store it between 32F and 104F | Intex Metal Frame manual |
| Steel wall pool, closing for winter | Do not drain it; lower it only to the maker's winter level | Atlantic: an empty pool can collapse in winter |
| Rain in the last 48 hours | Wait | Louisville MSD |
| Air above 85F or a hot, sunny day | Wait for a cooler or overcast day | Abilene; Ocean Blue (vinyl shrinks in sun) |
| Your home is on a septic system | Do not drain into it; use the lawn | Jefferson County, MO; Abilene |
| Chlorine tests above 0.1 mg/L | Stop chlorinating 5 to 10 days or add a dechlorinator, then retest | Abilene; Jefferson County; Augusta |
| Sewer cleanout limit is 20 gpm and you own a 30 gpm pump | Throttle it, or siphon (about 4.7 gpm) instead | Abilene; Jefferson County; K2 |
Sources: Doughboy; Intex; Atlantic; Louisville MSD; Abilene; Jefferson County; Augusta; Ocean Blue; K2. Download CSV
Winter is the most common wrong reason to drain. Steel wall makers want the pool left up and full to their winter line, and the steps and water levels are in our guide on how to close an above ground pool. A professional drain runs $180 to $230 in Angi’s 2026 data, and a liner swap usually includes it, priced in our pool liner replacement cost guide.
| Number | Value | Source |
|---|---|---|
| Chlorine limit before pool water reaches a storm drain | Under 0.1 mg/L | Augusta; Jefferson County; Southlake |
| Days of sun to dechlorinate | 5 to 10 | Abilene |
| Water to leave in a steel wall pool when draining to clean | At least 12 in | Doughboy |
| Sewer flow caps in five cities | 12 to 15, 20, 30 and 50 gpm | Augusta, Abilene and Jefferson County, Louisville, Southlake |
| 24 ft round, 52 in wall | 13,594 gallons | City of Akron |
| 1/4 HP K2 pump flow at 0 ft and 5 ft lift | 1,800 and 1,550 GPH | K2 spec sheet |
| Water pressure per foot of depth | 0.433 psi | Milwaukee Valve |
| Professional drain | $180 to $230 | Angi, 2026 data |
Sources: Augusta; Abilene; Doughboy; Louisville MSD; Southlake; Jefferson County; City of Akron; K2; Milwaukee Valve; Angi. Download CSV
How we compiled this
We read 21 primary documents in November 2026: pool draining rules from Augusta, Louisville MSD, Jefferson County (Missouri), Southlake and Abilene; liner warranties and instructions from Swimline, GLI, Blue Wave, LinerWorld and Ocean Blue; pool manuals from Doughboy, Atlantic, Intex and Backyard Leisure; the K2 pump spec sheet; Hoselink’s hose flow table; Milwaukee Valve’s pressure note; and the City of Akron gallons table. Drain times are our arithmetic and the siphon rows are estimates; we did not drain a pool or time a hose. Forum threads were read for question wording only.
Frequently Asked Questions
How do you drain water from an above ground pool?
Stop chlorinating 5 to 10 days ahead (Abilene) and test under 0.1 mg/L, unplug the filter pump, then siphon with a garden hose, open the drain valve on a frame pool, or set a submersible pump on the floor. Route the hose to your lawn or sewer cleanout at the local cap, such as 20 gpm in Abilene, and leave 12 inches unless the liner is coming out.
How do I get water out of my pool without a pump?
Siphon it with a garden hose: fill the hose with pool water, keep one end submerged and run the other end downhill. A 50 ft, 5/8 inch hose starts near 4.7 gpm from 4 ft of water (PC&S estimate from Hoselink data) and slows as the level drops. The outlet must sit below the water surface, so run it 3 ft downhill to reach the floor.
How to get water out of the bottom of an above ground pool?
Use a pump that works in shallow water, then a wet/dry vac. The K2 UTA02502K utility pump switches off at 1/4 inch, a Cover Care Model 300 cover pump reaches 1/8 inch, and the vac takes the final puddle. On an Intex frame pool, lift the wall opposite the drain valve to lead the last water out.
Should you drain an above ground pool for winter?
Not a steel or resin wall pool: Atlantic warns an empty pool can collapse in winter, and Swimline, GLI and Blue Wave void shrinkage coverage if the pool is emptied. Lower it only to the maker’s winter level. Frame pools are different: Intex says to drain, dry and store them once temperatures fall below 41F.
How do you drain an above ground pool with a hose?
Either siphon over the wall or screw the hose onto the drain valve. On an Intex frame pool, attach the garden hose to the drain connector, push it onto the valve and the water starts at once. For a siphon, fill the hose, keep one end under water and lay the other downhill; one hose drains a 24 ft round in roughly 96.2 hours.
How long does it take to drain a 24 foot above ground pool?
About 8.7 hours with a 1/4 HP pump at 26 gpm, 11.3 hours at a 20 gpm sewer cap, and roughly 96.2 hours with one garden hose siphoning to ground level, for the 13,594 gallons the City of Akron lists for a 24 ft round with a 52 inch wall. A 48 inch wall holds 11,895 gallons.
Sources
- Augusta, Georgia Engineering Department. A Guide to Swimming Pool Discharges. Accessed 2026-11-10.
- Louisville and Jefferson County Metropolitan Sewer District. Safe Swimming Pool Draining Tips Offered as Summer Closes (Sept 3, 2024). Accessed 2026-11-10.
- Jefferson County, Missouri Stormwater Management Division. Draining Swimming Pools. Accessed 2026-11-10.
- City of Southlake, Texas. Draining Your Pool? What You Should Know. Accessed 2026-11-10.
- City of Abilene, Texas Stormwater Services. Swimming Pool Water Disposal. Accessed 2026-11-10.
- Swimline (PDF hosted by The Pool Factory). Thirty Year Liner Warranty. Accessed 2026-11-10.
- Swimline (PDF hosted by The Pool Factory). Twenty-Five Year Liner Warranty. Accessed 2026-11-10.
- GLI Pool Products. Above Ground Liner Standard Warranty. Accessed 2026-11-10.
- Blue Wave Products (via Pro Pools). Above-Ground Pool Liner Installation Instructions. Accessed 2026-11-10.
- Ocean Blue Water Products (via Pro Pools). Fifteen Year Liner Warranty. Accessed 2026-11-10.
- LinerWorld. Liner Installation Instruction Manual. Accessed 2026-11-10.
- Backyard Leisure Pools. Warranty and Consumer Support Program. Accessed 2026-11-10.
- Doughboy. Round pool assembly and installation instructions. Accessed 2026-11-10.
- Atlantic Pool Products. Channel-Lok 1 Oval Pools manual. Accessed 2026-11-10.
- Intex. Metal Frame Pool owner's manual (87PO, 2022). Accessed 2026-11-10.
- K2 Pumps (via Lowe's). UTA02502K Automatic Submersible Utility Pump spec sheet. Accessed 2026-11-10.
- Hoselink. Garden Hose Flow Rate: GPM Explained. Accessed 2026-11-10.
- Milwaukee Valve. Understanding Column Pressure. Accessed 2026-11-10.
- City of Akron, Ohio. How to calculate the gallons in a swimming pool. Accessed 2026-11-10.
- PoolWeb. Cover pump listings (Cover Care Model 300). Accessed 2026-11-10.
- SwimmingPool.com (Pool Corporation). How to Empty an Above Ground Pool. Accessed 2026-11-10.
- The Pool Factory. Draining Your Above Ground Pool. Accessed 2026-11-10.
- Angi. How Much Do Swimming Pool Repairs Cost? (2026 data). Accessed 2026-11-10.
- PC&S research. Cost to Fill a Pool in 25 US Cities. Accessed 2026-11-10.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.