
Semi Inground Pool Guide: How Deep Each Maker Allows, Cost, Installation and Code
A semi inground pool is set partly below grade: maker documents allow 24 to 27 in of a 52 or 54 in wall on many kits, and HomeGuide prices installs at $7,000 to $25,000.
- ✓Burial limits from 17 documentsDepth, backfill, collar and warranty rules for Radiant, Doughboy, Wilbar, Latham and more.
- ✓Dig and concrete math53.3 cu yd out and 6.4 cu yd of collar for a 16 x 32 ft pool set 24 in down.
- ✓Barrier rules that changeWhy a 52 in wall buried 24 in stops counting as the pool fence under ISPSC 305.5.
Key takeaways
- Burial limits differ by document: Wilbar allows 27 in, Latham’s Bar Top caps burial at halfway, and the Doughboy Hydrosphere goes from 24 in to fully inground (Wilbar; Bar Top manual; Hydrosphere guide).
- Embassy PoolCo and Lomart warranties void all coverage if the wall is buried beyond leveling, and Sharkline requires separate retailer instructions for any depth (Embassy; Lomart; Sharkline).
- Under 2024 ISPSC 305.5 a pool wall is a barrier only if its bottom sits on grade and its top stands 48 in above grade, so a 52 in wall buried 24 in needs 20 in more on top or a fence (ISPSC 2024).
- HomeGuide prices a semi-inground pool at $7,000 to $25,000 installed, against $1,600 to $7,500 for above-ground and $44,499 to $87,349 for inground in Angi’s 2026 data (HomeGuide; Angi).
- A 16 x 32 ft pool set 24 in deep with a 2 ft over-dig moves about 53.3 cu yd of soil and takes about 6.4 cu yd of concrete for a 10 in collar (PC&S arithmetic from the Hydrosphere guide).
What is a semi inground pool?
A semi inground pool is a pool whose wall is partly buried and partly above grade, usually wrapped by a deck on the exposed side. Most are 52 or 54 in wall systems sold with burial instructions, such as the Doughboy Hydrosphere set 24 in deep. The 2024 ISPSC has no semi-inground category: Section 801.1 counts permanent pools that sit partly above grade as inground pools.
| Key number | Value | Source |
|---|---|---|
| Installed cost, semi inground pool | $7,000 to $25,000 | HomeGuide, July 2025 |
| Installed cost, above-ground pool | $1,600 to $7,500 | HomeGuide, June 2024 |
| Installed cost, inground pool | $44,499 to $87,349 (average $65,909) | Angi, August 2026 |
| Burial most kits allow, per retailer | Halfway: 26 in on a 52 in wall, 27 in on a 54 in wall | The Pool Factory (retailer), November 2024 |
| Depth range in 17 maker documents | 0 in (warranty void) to fully inground | PC&S table below, October 2026 |
| Concrete collar trigger, Radiant Metric | Any point of the wall 26 in or more in the ground | Radiant manual, 2023 |
| Pool wall as its own barrier | Bottom on grade and top 48 in or more above grade | 2024 ISPSC 305.5 |
| Building permit exemption | Only prefabricated pools less than 24 in deep | 2021 IRC R105.2 |
Sources: HomeGuide inground guide (July 16, 2025); HomeGuide above-ground guide (June 10, 2024); Angi (updated Aug 5, 2026); The Pool Factory; Radiant Metric manual; 2024 ISPSC Chapter 3; 2021 IRC R105.2. Download CSV
Three kinds of pool get sold under the name. The first is a steel, aluminum or resin wall kit with a burial document, such as Latham’s 52 in Bar Top system, which its manual says can go above-ground, partly or completely in-ground (Bar Top manual). The second is a panel system built for all three installs: Latham describes its Radiant panels as 2 in thick, with a foam core bonded between acrylic coated aluminum sheets (Latham).
The third is an inground-grade shell set high. ICC-ES report ESR-2014 lets the fiberglass models in its Table 3 stand up to 19 1/2 in above ground, painted with a UV-inhibiting coating unless soil or decking shades them (ICC-ES ESR-2014). Plungie, a precast pool maker, prices precast concrete set semi-recessed at $40,000 to $75,000 (Plungie, May 2026).
The code label matters for permits. ISPSC 801.1 says permanent inground residential pools include pools partly or entirely above grade, and leaves out pools made for above-ground use that can be taken apart and stored; those fall under Chapter 7, the onground storable chapter (ISPSC 801.1; ISPSC 701.1). Ask your building department which chapter it applies to the kit you are pricing.
Which pools can be partly buried, and how deep?
Only pools whose maker publishes burial rules. In the 17 documents we read, the allowed depth runs from 0 in, where Embassy, Lomart, Sharkline and Backyard Leisure void the warranty without separate instructions, through 12 in for Islamorada and 26 to 27 in for Latham’s Bar Top and Wilbar, to fully inground for Radiant Metric, Doughboy Hydrosphere and Aquasport 52.
| Maker and product | Wall type | Partial burial allowed? | Maximum depth in ground | Backfill, base or collar | Wall heights named | Burial and the warranty | Document | Document URL |
|---|---|---|---|---|---|---|---|---|
| Radiant Metric (Radiant Pools, Latham) | Insulated panel: foam core between aluminum sheets | Yes | Fully inground; 8 x 16 in concrete collar once any point is 26 in or more down | Structural fill, no clay; hand compact every 8 to 12 in as the pool fills; French drain uphill | 52 in | Manual: not following it voids all warranties; Latham: lifetime non-prorated panel warranty | Radiant Metric Round Installation Manual (2023) and FAQ | https://www.radiantpools.com/application/files/7217/0179/1874/2023_Radiant_Metric_Round_Installation_Manual_R3_LR.pdf |
| Doughboy Hydrosphere (Doughboy Plus) | Steel panels with buttress braces | Yes | 24 in recommended (18 in minimum) up to fully inground | 2 in masonry sand floor; collar 8 to 10 in deep, 2 ft wide, 3,000 psi; sump pump if water table is high | 52 in | Structure: limited lifetime warranty | Semi-Inground Hydrosphere Pool Installation Guide | https://doughboyplus.com/content/guides/Semi-Inground_Hydrosphere_Pool_Installation_Guide.pdf |
| Doughboy below-grade kit (HII 573-3491) | Steel wall above-ground pool | Yes | To 6 in below the top rail (46 in on a 52 in wall); 9 in with a concrete deck | Slurry mix backfill; 18 in over-dig; fill to 1 to 2 in of the top first; earth cove, no foam cove | 48, 52, 54 in | Not following these instructions voids the warranty; professional installers only | Below-Grade Pool Installation Instructions 573-3491 | https://cdn.shopify.com/s/files/1/0535/5569/1698/files/573-3491-HII-BelowGrade-installation.pdf?v=1665412541 |
| Doughboy round pools (573-3615) | Steel wall above-ground pool | No | None with these instructions; use the below-grade kit | Not stated | Not stated | Burial only with the separate below-grade instructions | Doughboy Round Pools instructions | https://godoughboypromotions.com/iframe/wp-content/uploads/2015/08/AG-DOUGHBOY-RND-POOLS-2.pdf |
| Wilbar International (RTR) | Above-ground frame and wall | Yes | 27 in | Sand or sifted soil, no rocks; pool full before backfill; grade away 10 degrees; keep 3/4 full | Not stated | Corrosion warranty stays; no cover for structural damage, frost heave or inward collapse | 27 in Below Grade Instructions (RTR) | https://cdn.shopify.com/s/files/1/0535/5569/1698/files/27_BELOW_GRADE_INSTRUCTIONS_RESIN_GUARD_24_PNU.pdf?v=1721396319 |
| Latham Bar Top 52 in | Steel on-ground panels | Yes | No more than halfway (26 in); ovals at least 14 in down | Oval cement pad 24 x 10 in; graded backfill and a drain pipe; clear stone plus sump for high water | 52 in | Ignoring the guidelines voids all warranties | 52 in Bar Top Installation Manual (2015) | https://poolsupplies.nyc3.cdn.digitaloceanspaces.com/media/913e98630441198566652f23c1ebdf46.pdf |
| Aquasport 52 | Interlocking aluminum panels | Yes | Fully in-ground; no concrete collar required | 2 in stone dust base; 3 ft extra excavation; 6 weeks before decking if fully in-ground | 52 in | Not stated | Aquasport 52 installation procedure | https://irp-cdn.multiscreensite.com/cdc08688/files/uploaded/%20Aquasport%2052%20installation%20procedure%20.pdf |
| Hydra Pools 52 in | Panel wall with steel or polymer steps | Yes | Not stated | Collar 3 ft wide, 1 ft deep with rebar; step footing 10 in into undisturbed earth | 52 in | Not stated | Hydra Pools Semi-Inground Pool Instructions (2024) | https://www.hydrapools.com/wp-content/uploads/2024/05/52-install-c.pdf |
| Funtastic (Pro Pools) | Steel wall panels | Yes | At least 2 ft down; maximum not stated | Compacted stone dust; footer 24 in wide, 10 in deep minimum; 6 in of backfill on skirting at most | Not stated | Not stated | The Funtastic Pool product guide | https://www.propools.com/Manuals/65918_1_202342563325.pdf |
| Latham fiberglass (ICC-ES ESR-2014) | One-piece fiberglass shell, 1/4 in minimum | Yes | Inground; Table 3 models may stand up to 19 1/2 in above ground | Bedding 3 in minimum; water fill and backfill together, tamped | n/a | Evaluation report, not a warranty | ICC-ES Evaluation Report ESR-2014 (Nov 2025) | https://icc-es.org/wp-content/uploads/report-directory/ESR-2014.pdf |
| Islamorada round | Metal wall above-ground pool | No | Recess only: 12 in on a 48 in pool, keeping 36 in above ground | Pool full 7 days before backfilling; plastic film against the wall | 48 in (example) | Not designed to be buried | Round Above Ground Pool Installation Instructions | https://www.propools.com/instructions_owners_manuals/islamorada-roundpool-instructions.pdf |
| Imperial Java round | Above-ground pool | Dealer decision | Ask the dealer first | Not stated | Not stated | Not stated | Pearl/Java Round Installation Manual (06.2023) | https://www.imperialpools.com/info/distribution/ag/docs/Pearl-Round-Installation-Manual.pdf |
| Embassy PoolCo (Skyline) | Above-ground portable pool | No | 0 in beyond leveling | n/a | n/a | Burial voids all warranties (20-year prorated) | Embassy PoolCo limited warranty | https://cdn.shopify.com/s/files/1/0535/5569/1698/files/Skyline_Warranty.pdf?v=1686088473 |
| Lomart Grey Mist II | Above-ground portable pool | No | 0 in beyond leveling | n/a | n/a | Burial voids all warranties (35-year prorated) | Lomart limited warranty | https://cdn.shopify.com/s/files/1/0535/5569/1698/files/Lomart_Grey_Mist_Warranty_35_Years_fa23e7aa-7532-40b1-a61d-7cba0ffdc27e.pdf?v=1666897344 |
| Sharkline | Above-ground pool | With separate instructions | 0 in unless the retailer supplies instructions | n/a | n/a | Below grade without those instructions: warranty null and void | Sharkline warranty terms | https://images.inyopools.com/cloud/documents/REPRIEVE-TIBURON-WILBAR-SHARKLINE-WARRANTYTERMS-CONDITIONS.pdf |
| Backyard Leisure | Above-ground pool | With separate instructions | 0 in unless the retailer supplies instructions | n/a | n/a | Below grade without those instructions: warranty null and void | Backyard Leisure warranty terms | https://cdn.shopify.com/s/files/1/0535/5569/1698/files/920045-BACKYARDLEISURE_WarrantyTerms-Conditions_d755dc8a-3324-4a05-ac38-9eee4cfd5534.pdf?v=1682682432 |
Documents: Radiant Metric manual; Radiant FAQ; Doughboy Hydrosphere guide; Doughboy Plus Hydrosphere page; HII 573-3491 below-grade instructions; Doughboy 573-3615; Wilbar RTR 27 in instructions; Latham Bar Top 52 in manual; Aquasport 52 procedure; Hydra Pools instructions; Funtastic guide; ICC-ES ESR-2014; Islamorada manual; Imperial Java manual; Embassy PoolCo warranty; Lomart warranty; Sharkline warranty; Backyard Leisure warranty. All opened October 27, 2026. PC&S compiled the table; makers did not review it. Download CSV
Doughboy 46 in = 52 in wall with 6 in kept above backfill and no deck. Bar Top 26 in = halfway on a 52 in wall. Islamorada 12 in on a 48 in wall.
Source: Radiant, Doughboy Plus, HII 573-3491, Aquasport, Wilbar, Latham Bar Top, Islamorada, Embassy, Lomart, Sharkline and Backyard Leisure documents, opened Oct 27, 2026. Download chart data (CSV)
Depth is not the only limit. Radiant requires a concrete collar at least 8 in deep and 16 in wide around the whole pool once any point of the wall is 26 in or more in the ground, and its table orders 3.75 yd of concrete for a 24 ft round (Radiant Metric manual, page 22). The Doughboy below-grade instructions keep at least 6 in between the top of the wall and the top of the backfill so the liner can still be replaced (HII 573-3491).

Retailer summaries round these rules up. The Pool Factory says most of its semi-inground models are warrantied for burial up to halfway, 26 in on a 52 in wall and 27 in on a 54 in wall, and its extruded aluminum Intrepid to 36 in (The Pool Factory). Wilbar’s own 27 in instructions keep only the corrosion warranty and exclude structural damage, frost heave and inward collapse (Wilbar).
Standard kits are a different product. Embassy PoolCo’s 20-year and Lomart’s 35-year prorated warranties both say burying the wall and frame below ground level, other than to level the pool, voids all warranties (Embassy; Lomart). Islamorada allows only a 12 in recess on a 48 in pool, keeping 36 in above ground; our guide on how to level ground for an above ground pool covers the dig-down method for those kits.
How much does a semi inground pool cost?
HomeGuide prices a semi inground pool at $7,000 to $25,000 installed (July 2025), between above-ground pools at $1,600 to $7,500 and inground pools at $44,499 to $87,349 (Angi, August 2026). Dealer and maker figures run higher: Fiesta Pools & Spas quotes $20,500 to $40,000 and Latham says a semi-inground install typically starts around $50,000.
| Pool type | Installed cost | Date | Source | Source type |
|---|---|---|---|---|
| Above-ground pool | $1,600 to $7,500 | June 2024 | HomeGuide | Cost guide |
| Semi-inground pool | $7,000 to $25,000 | July 2025 | HomeGuide | Cost guide |
| Semi-inground kit plus pro install | $11,000 to $30,000 (kit $6,000 to $15,000 plus install $5,000 to $15,000) | December 2025 | Royal Swimming Pools | Retailer blog |
| Semi-inground, dealer install | $20,500 to $40,000 | August 2025 | Fiesta Pools & Spas | Dealer |
| Semi-inground, Latham builder network | Typically starts around $50,000 | October 2026 | Latham Pool Products | Manufacturer |
| Fiberglass set semi-recessed | $45,000 to $90,000 | May 2026 | Plungie | Precast pool maker blog |
| Inground pool | $44,499 to $87,349 (average $65,909) | August 2026 | Angi | Cost guide |
Sources: HomeGuide above-ground guide (June 10, 2024); HomeGuide inground guide (July 16, 2025); Royal Swimming Pools (Dec 3, 2025); Fiesta Pools & Spas (Aug 5, 2025); Latham (opened Oct 27, 2026); Plungie (May 7, 2026); Angi (updated Aug 5, 2026). Download CSV
Royal row adds its kit and install ranges. Latham's 'starts around $50,000' is a single figure and sits in the table only.
Source: HomeGuide (2024, 2025), Royal Swimming Pools (2025), Fiesta Pools & Spas (2025), Plungie (2026), Angi (2026). Download chart data (CSV)
The kit is the smaller share. On October 27, 2026 The Pool Factory listed a 16 x 32 ft, 54 in Saltwater Titan oval at $5,650 and Pro Pools listed a 16 x 28 ft Doughboy Hydrosphere kit at $10,403.18 (The Pool Factory; Pro Pools). Royal Swimming Pools puts professional installation at $5,000 to $15,000 on top of a $6,000 to $15,000 kit (Royal). Fully inground vinyl kits from the same seller listed at $8,851.73 to $18,177.54 on November 2, 2026, compared size by size in our inground pool kits guide.
| Retailer | Kit | Wall | Listed price | Regular price | Seen |
|---|---|---|---|---|---|
| The Pool Factory | Melenia round, 24 ft | 54 in | $2,539 | $3,795 | Oct 27, 2026 |
| The Pool Factory | Saltwater Titan oval, 16 x 32 ft | 54 in | $5,650 | $8,095 | Oct 27, 2026 |
| The Pool Factory | Tribeca oval, 15 x 30 ft | 54 in | $5,769 | $7,695 | Oct 27, 2026 |
| The Pool Factory | Daytona oval, 18 x 40 ft | 54 in | $6,965 | $9,295 | Oct 27, 2026 |
| The Pool Factory | Intrepid aluminum oval, 12 x 24 ft | 54 in | $7,756 | $9,695 | Oct 27, 2026 |
| Pro Pools | Doughboy Hydrosphere freeform kit, 13 x 22 ft | 52 in | $9,014.21 | n/a | Oct 27, 2026 |
| Pro Pools | Doughboy Hydrosphere freeform kit, 16 x 28 ft | 52 in | $10,403.18 | n/a | Oct 27, 2026 |
| Pro Pools | Doughboy Hydrosphere freeform package, 18 x 32 ft | 52 in | $10,947.94 | n/a | Oct 27, 2026 |
Sources: The Pool Factory semi-inground collection; Pro Pools Hydrosphere listings. Sale prices change often; recheck before you budget. Download CSV
Site work moves the total most. Plungie lists cladding or a retaining wall at $5,000 to $20,000 or more, decking at $7,000 to $25,000 or more, fencing at $2,000 to $13,500, electrical at $2,000 to $5,000 and permits at $100 to $1,800 (Plungie). HomeGuide puts inground excavation at $1,000 to $5,000 (HomeGuide). For the ends of the range, compare our above ground pool cost guide and our inground pool cost breakdown.
How much digging and backfill does a 16 x 32 semi-inground pool need?
About 53.3 cubic yards of soil for a 16 x 32 ft pool set 24 in deep with the 2 ft over-dig the Hydrosphere guide specifies. A 10 in deep, 2 ft wide concrete collar takes about 6.4 cubic yards, about 9.0 cubic yards of backfill goes back on top of it, and about 44.3 cubic yards is left to spread or haul, measured before swell.
| Step | Input or formula | Result | Source |
|---|---|---|---|
| Pool footprint | 16 x 32 ft rectangle | 512 sq ft | PC&S arithmetic |
| Dig area with over-dig | 2 ft all round: 20 x 36 ft | 720 sq ft | Hydrosphere guide (2 ft over-dig) |
| Depth in the ground | 24 in, the depth the guide calls most common | 2 ft | Hydrosphere guide |
| Soil dug out | 720 sq ft x 2 ft = 1,440 cu ft, divided by 27 | 53.3 cu yd (before swell) | PC&S arithmetic |
| Sand floor | 512 sq ft x 2 in = 85.3 cu ft | 3.2 cu yd | Hydrosphere guide (2 in masonry sand) |
| Over-dig ring | 720 minus 512 sq ft | 208 sq ft | PC&S arithmetic |
| Concrete collar, Hydrosphere spec | 208 sq ft x 10 in = 173.3 cu ft | 6.4 cu yd (5.1 cu yd at 8 in) | Hydrosphere guide (8 to 10 in deep, 2 ft wide) |
| Concrete collar, Radiant spec | 16 in wide ring 135.1 sq ft x 8 in = 90.1 cu ft | 3.3 cu yd geometric; Radiant's table says 4.25 yd for a 30 ft round | Radiant manual, page 22 |
| Backfill above the collar | 208 sq ft x 14 in (24 minus 10) = 242.7 cu ft | 9.0 cu yd | PC&S arithmetic |
| Spoil to spread or haul | 53.3 minus 9.0 cu yd | 44.3 cu yd (before swell) | PC&S arithmetic |
| Wall left above grade | 52 in minus 24 in | 28 in | PC&S arithmetic |
| Top-mounted barrier to reach 48 in | 48 in minus 28 in | 20 in or more | 2024 ISPSC 305.5 |
| Water in the pool | 16 x 32 ft at 4 ft average depth | about 15,400 gal | City of Akron table |
| Water weight | 15,400 gal x 8.34 lb | about 128,400 lb | USGS water density |
Inputs: Doughboy Hydrosphere guide (2 ft over-dig, 24 in depth, 10 in by 2 ft collar, 2 in sand); Radiant Metric manual (16 x 8 in collar, concrete table); City of Akron (gallons); USGS (8.34 lb per gallon); 2024 ISPSC 305.5. Volumes are PC&S arithmetic, in place before swell. Download CSV

Order concrete from the maker’s table, not from bare geometry. A Radiant-spec collar, 16 in wide and 8 in deep, works out to 3.3 cu yd around this 96 ft perimeter, yet Radiant’s table lists 4.25 yd for a 30 ft round with a 94 ft perimeter (Radiant). The Hydrosphere guide asks for ready mix footer mix at 3,000 psi with a 3 in slump.
Water and soil have to rise together. This pool holds about 15,400 gallons at a 4 ft average depth in the City of Akron’s table, about 128,400 lb at 8.34 lb per gallon (City of Akron; USGS). That water presses on the wall at about 250 lb per sq ft at the floor, which is why ICC-ES ESR-2014 requires water fill and backfill to run at the same time and Radiant tells installers to backfill as the pool fills.
How is a semi-inground pool installed, step by step?
Call 811, get the permit, dig the pool area plus an over-dig of 18 in to 3 ft depending on the manual, level it to within 1 in, set and plumb the wall, bond it, pour the collar, then fill the pool and backfill together. The steps below carry the measurement each manufacturer document sets, so you can check a contractor’s plan against it.
- Confirm the burial documentGet the maker’s below-grade instructions for your exact model: 27 in for Wilbar RTR, halfway for Bar Top, 24 in recommended for Hydrosphere.
- Call 811 and file the permitContact 811 a few business days before digging; the service is free. Most semi-inground pools are over the 24 in IRC R105.2 exemption.
- Dig with an over-digAdd 18 in all round (Doughboy 573-3491), 2 ft (Hydrosphere) or 3 ft (Hydra, Aquasport). Hydrosphere: 18 in minimum depth, 24 in most common.
- Level and lay the baseLevel to within 1 in (Hydra) or 1/2 in on 2 in of stone dust (Aquasport). Spread 2 in of masonry sand on the floor (Hydrosphere).
- Set and plumb the wallBolt the panels, set braces and plumb them with shims; Hydrosphere bans pressure-treated wood shims. Pump out groundwater first if the water table is high.
- Bond and plumb before you buryHave the electrician bond the pool before the collar pour (Radiant). Hard-plumb with rigid PVC so buried lines cannot collapse (Doughboy 573-3491).
- Pour the collarHydrosphere: 8 to 10 in deep, 2 ft wide, 3,000 psi. Radiant: 8 x 16 in once any point is 26 in down. Hydra: 3 ft wide, 1 ft deep with rebar.
- Fill and backfill togetherBackfill in 8 to 12 in lifts as the pool fills, hand compaction only (Radiant). Doughboy: fill to 1 to 2 in of the top before slurry. Islamorada: full for 7 days first.
- Grade away and waitSlope backfill away: 10 degrees (Wilbar) or 1/4 in per ft (Doughboy). Add a French drain uphill (Radiant). Wait 6 weeks before decking a fully buried Aquasport.
How do drainage and groundwater affect a semi-inground pool?
Groundwater pushes on a buried wall from outside, and only the pool water pushes back. Radiant warns that a high water table can damage walls, especially in an empty pool. Wilbar requires the pool to stay at least three-quarters full, and Doughboy’s below-grade instructions say to keep the pool water above the surrounding water table so the liner does not float.
- Radiant: redirect uphill run-off around the pool with a French drain, a perforated pipe and a relief area away from the pool, and never leave the pool empty (Radiant FAQ).
- Latham Bar Top: grade the backfill to drain away and run a drainage pipe around the pool to a low area; with a high water table, dig 6 in deeper, fill with clear stone and pump from a sump (Bar Top manual).
- Doughboy 573-3491: skip preformed foam coves, which a rising water table can lift; use a cove of screened damp earth and add a sump pump in heavy clay (HII 573-3491).
- Wilbar: drain the pool only in the dry season, when groundwater sits below the pool floor, or the wall can collapse inward (Wilbar).
- ICC-ES ESR-2014: stop and call a registered design professional if groundwater, uncompacted fill or expansive soil turns up in the excavation (ESR-2014).
The arithmetic shows why. With groundwater at grade, the bottom of a wall buried 24 in carries about 125 lb per sq ft of water pressure alone (62.4 lb per cubic foot times 2 ft, from USGS density), before soil adds its share. A full pool pushes back with about 250 lb per sq ft at the floor; an empty one pushes back with nothing.
Does a semi inground pool need a fence?
Usually, yes. Under 2024 ISPSC 305.5 a pool wall alone counts as the barrier only if its bottom sits on grade, its top is at least 48 in above grade all the way round and the maker allows it. A 52 in wall buried 24 in shows 28 in, so it needs a barrier mounted on top that reaches 48 in, or a separate fence.
| Setup | Wall above grade | Counts as the barrier? | Rule |
|---|---|---|---|
| 52 in wall set on grade, maker allows the wall as a barrier, ladder removable or lockable | 52 in | Yes | 2024 ISPSC 305.5 items 1, 3 and 4 |
| Same 52 in wall buried 24 in, nothing on top | 28 in | No | 305.5 item 1: bottom must be on grade and top 48 in above grade |
| 52 in wall buried 24 in with a barrier mounted on top, top 48 in or more above grade, gap 4 in or less | 28 in plus 20 in or more | Yes | 305.5 items 2 and 5; 305.2.1 |
| 54 in wall buried 6 in, nothing on top | 48 in | No under the ISPSC | 305.5 item 1 needs the bottom on grade; IRC AG105.2 item 1 has no on-grade test, so ask which edition your town uses |
| Deck or soil berm built against the outside of the wall | Measured from the deck or berm | Only if 48 in holds above that surface for 3 ft out | 305.2.1 item 1 |
| Separate fence around the pool | Any | The fence is the barrier | 305.2: 48 in minimum, 2 in gap over grass, 4 in over concrete, 4 in sphere |
Sources: 2024 ISPSC Sections 305.2.1 and 305.5 (same wording in the 2021 edition); IRC Appendix G AG105.2 (Philadelphia Residential Code 2018 copy); CPSC Publication 362. Download CSV

Older rules read differently. IRC Appendix G, still in force where a town adopted it, says the top of the barrier must be 48 in above grade measured on the side away from the pool and lets an above-ground pool structure serve as the barrier or carry one on top, with no on-grade test (AG105.2). CPSC Publication 362 gives the same two options for above-ground pools (CPSC).
State law can raise the bar. As of October 4, 2026, 20 of 51 jurisdictions required a residential pool barrier statewide, and Arizona and California set 60 in instead of 48 in (PC&S pool fence laws by state; A.R.S. 36-1681). Our pool fence cost guide prices the fence options per linear foot.
Do you need a permit for a semi-inground pool?
In most places, yes. IRC R105.2 exempts only prefabricated pools less than 24 in deep, and semi-inground walls run 48 to 54 in. Applied to the same $68,000 inground pool, official fee schedules in 18 US cities and counties charged from $110 in Chandler, Arizona to $3,940.31 in San Diego in October 2026, with a middle value of $500.
Expect the building department to ask how deep the wall goes. Latham’s Bar Top manual warns that a pool set more than halfway into the ground may be treated as an inground pool, and that a fully buried install may need engineering and extra permits (Bar Top manual). Radiant tells owners to check local building codes before any inground install (Radiant).
- Which chapter applies: ISPSC Chapter 7 (onground storable) or Chapter 8 (permanent inground, which includes pools partly above grade)?
- Does the wall need a stamped design at the depth you plan, or is the maker’s below-grade sheet enough?
- Is the barrier a top-mounted fence, a perimeter fence or the house wall with alarms, and when is it inspected?
- Are electrical bonding and the deck separate permits, and must bonding be inspected before backfill?
Fees depend on the formula. Phoenix and Fort Worth charge on declared valuation while San Diego charges a flat per-pool fee, so a lower semi-inground contract price lowers the fee only in valuation towns (PC&S pool permit cost ledger; San Diego Information Bulletin 501). Our pool permit guide lists inspection steps and waits by city.
What decking works around a semi-inground pool?
Most semi-inground pools get a raised wood or composite deck on one or more sides, because 24 to 28 in of wall stays above grade. HomeGuide prices pressure-treated pine pool decks at $25 to $50 per sq ft installed and composite at $40 to $80, while a simple concrete deck at grade runs $6 to $11 (ConcreteNetwork, February 2026).
| Deck option | Installed price | Code or maker rule | Source |
|---|---|---|---|
| Pressure-treated pine, raised | $25 to $50 per sq ft | Board gaps 1/8 to 1/2 in (ISPSC 306.6); guards 36 in high if more than 30 in above grade (IRC R312) | HomeGuide, Dec 2025 |
| Composite, raised | $40 to $80 per sq ft | Gaps per the board maker (ISPSC 306.6); slope at least 1/8 in per ft unless gapped | HomeGuide, Dec 2025 |
| Wood deck, general | $15 to $40+ per sq ft | Same as above | ConcreteNetwork, Feb 2026 |
| Concrete at grade, simple design | $6 to $11 per sq ft | Slope 1/8 to 1/2 in per ft; Radiant allows sonotubes at collar pour to carry a deck | ConcreteNetwork, Feb 2026; Radiant manual |
| Concrete or paver deck on a Doughboy below-grade pool | n/a | Keep 9 in between top rail and grade so the liner can be replaced | Doughboy 573-3491 |
| Any deck on a fully buried Aquasport 52 | n/a | Wait 6 weeks after backfill so the soil settles | Aquasport 52 procedure |
Sources: HomeGuide pool deck cost (Dec 22, 2025); ConcreteNetwork (updated Feb 13, 2026); 2024 ISPSC 306.5 and 306.6; 2021 IRC R312; Radiant manual; HII 573-3491; Aquasport 52 procedure. Download CSV
Deck height sets two separate rules. IRC R312 requires guards at least 36 in high on any walking surface more than 30 in above grade, so a deck level with a 28 in wall top needs no guard, yet the pool barrier rules in ISPSC 305 still apply to it (IRC R312). ISPSC 306.5 caps deck slope at 1/2 in per ft (ISPSC 306).
For 200 sq ft of deck, HomeGuide’s pool deck table gives $5,000 to $10,000 installed (HomeGuide). Our pool deck materials comparison covers slip, heat and freeze data for each surface.
Are semi inground pools a good idea?
They suit a sloped or rocky yard and a budget between above-ground and inground prices, provided the wall system carries burial instructions. They suit a flat yard less: a 52 in wall on grade can serve as its own barrier under ISPSC 305.5, while burying it adds a collar, drainage work and a top-mounted barrier or fence that the above-ground version skips. For a full inground pool on a steeper grade, the cut, fill, wall and setback options are compared in our pool on a slope guide.
| If your situation is | Do this |
|---|---|
| The yard falls 12 in or more across the pool site | Pick a wall system whose manual allows burial, set the uphill side into the slope and add a French drain uphill (Radiant) |
| You already own a standard above-ground kit | Read its warranty first: Embassy, Lomart, Sharkline and Backyard Leisure void coverage for burial without separate instructions |
| You want the pool wall to be the only barrier | Keep the wall on grade with 48 in or more showing (ISPSC 305.5); any burial needs a top-mounted barrier or a fence |
| The water table is high or the soil is clay | Plan a sump (Hydrosphere, Bar Top) and structural fill (Radiant bans clay backfill); keep the pool at least 3/4 full (Wilbar) |
| The budget is under $10,000 all in | Price an above-ground pool on grade: $1,600 to $7,500 installed (HomeGuide) |
| You want water deeper than about 4 ft | Ask for an expandable liner or a deep-end design; Hydrosphere is flat bottom, Latham lists deep ends up to 8 ft |
| More than half the wall will be below grade | Ask the building department if it treats the pool as inground (ISPSC 801.1) and whether stamped engineering is needed (Bar Top manual) |
| The deck will sit more than 30 in above grade | Add 36 in guards (IRC R312) on top of the pool barrier rules |
Sources: Radiant; Embassy; Lomart; Sharkline; Backyard Leisure; ISPSC 305.5; Hydrosphere; Bar Top; Wilbar; HomeGuide; Latham; ISPSC 801.1; IRC R312. Download CSV
| What a ranking page says | What the primary document says | Sources |
|---|---|---|
| Many semi-inground kits allow 36 to 48 in of burial (Royal Swimming Pools, Dec 2025) | Wilbar allows 27 in, Latham's Bar Top caps burial at halfway (26 in on 52 in) and Islamorada allows a 12 in recess; only some systems go fully inground | Royal; Wilbar; Bar Top; Islamorada |
| Most models are warrantied for burial up to halfway (The Pool Factory) | Wilbar's 27 in instructions keep the corrosion warranty only; structural damage, frost heave and inward collapse are excluded | Pool Factory; Wilbar |
| A semi-inground install typically starts around $50,000 (Latham) | HomeGuide lists $7,000 to $25,000 and Fiesta quotes $20,500 to $40,000; the gap is scope (decking, panels, builder labor) | Latham; HomeGuide; Fiesta |
| Most places require a barrier at least 48 in tall (Royal) | True, and a buried wall usually fails it: ISPSC 305.5 counts the wall only when its bottom is on grade | Royal; 2024 ISPSC 305.5 |
Sources: Royal Swimming Pools (Dec 3, 2025); The Pool Factory; Latham; HomeGuide; Fiesta; Wilbar; Bar Top; Islamorada; ISPSC 305.5. Download CSV
If the budget points at a small inground pool instead, our small inground pool cost guide shows permit-declared values by size, and our fiberglass pool cost guide covers one-piece shells, which ICC-ES ESR-2014 allows to stand up to 19 1/2 in above ground for listed models.
How we compiled this
We read 17 manufacturer installation documents, warranties and one ICC-ES evaluation report, the 2024 ISPSC, the 2021 IRC and IRC Appendix G on UpCodes, CPSC Publication 362, and dated price pages from HomeGuide, Angi, ConcreteNetwork, two online retailers, two dealers and Plungie, all opened October 27, 2026. Volumes and pressures are our arithmetic from the inputs shown. We did not install, test or inspect any pool, and we excluded forum posts as sources.
Frequently Asked Questions
How deep can a semi-inground pool be in the ground?
As deep as the maker’s document allows: 12 in on a 48 in Islamorada pool, halfway (26 in) on Latham’s 52 in Bar Top, 27 in under Wilbar’s instructions, and fully inground for Radiant Metric and the Doughboy Hydrosphere (Bar Top; Wilbar). Hydrosphere recommends 24 in. Standard Embassy and Lomart kits lose their warranty if buried.
Are semi-inground pools cheaper?
Cheaper than inground, dearer than above-ground. HomeGuide lists $7,000 to $25,000 installed for semi-inground pools against $1,600 to $7,500 for above-ground (HomeGuide), and Angi puts inground pools at $44,499 to $87,349 in 2026. Builder quotes run higher: Fiesta Pools & Spas quotes $20,500 to $40,000, and Latham says installs typically start around $50,000.
What are the downsides of a semi-inground pool?
A buried wall usually stops counting as the pool barrier under ISPSC 305.5, so you add a top-mounted barrier or a fence. Groundwater can push the wall in if the pool is drained, which is why Wilbar requires it to stay three-quarters full (Wilbar). Many standard kits void their warranty when buried, and decks, collars and drains add cost.
What is the life expectancy of a semi-inground pool?
Warranties give the best guide. Radiant panels carry a lifetime non-prorated warranty, the Hydrosphere structure a limited lifetime warranty, and Latham warrants its vinyl liners for 20 years (Latham). Liners wear out before walls: HomeGuide puts vinyl liner replacement at $3,000 to $7,500 about every 10 years for inground pools.
Can you bury a regular above ground pool?
Only with the maker’s below-grade instructions. Doughboy’s round pool instructions say its pools are not designed to be buried without them, Islamorada allows a 12 in recess at most, and Embassy PoolCo’s warranty says burying the wall below ground level voids all warranties (Doughboy; Embassy). Outside soil pressure can collapse a thin wall.
What is the deepest semi-inground pool you can get?
Latham says its semi-inground pools can range from a 3 ft shallow end to an 8 ft deep end, with some at a uniform 4 or 5 ft (Latham). The Doughboy Hydrosphere has a flat bottom, and Doughboy’s round instructions allow a deeper swim area only with a liner labeled 20 or 25 mil expandable. None of these is a diving pool.
Do semi-inground pools need a concrete base?
Most need a concrete collar around the base of the wall, not a slab under the floor. Radiant requires an 8 x 16 in collar once any point is 26 in down, the Hydrosphere guide an 8 to 10 in deep, 2 ft wide collar, and Latham’s Bar Top ovals a 24 x 10 in pad (Radiant). Aquasport says its 52 in pool needs no collar.
Sources
- Radiant Pools. Radiant Metric Round Installation Manual (2023, R3). Accessed 2026-10-27.
- Radiant Pools. Frequently Asked Questions (backfill, drainage, concrete collar). Accessed 2026-10-27.
- Doughboy Plus. Semi-Inground Hydrosphere Pool Installation Guide. Accessed 2026-10-27.
- Doughboy Plus. Hydrosphere Series Pool Packages. Accessed 2026-10-27.
- HII Industries (Doughboy), hosted by Pool Nation. Below-Grade Pool Installation Instructions 573-3491. Accessed 2026-10-27.
- Doughboy. Doughboy Round Pools assembly and installation instructions 573-3615. Accessed 2026-10-27.
- Wilbar International, hosted by Pool Nation. 27 in Below Grade Instructions (RTR). Accessed 2026-10-27.
- Sharkline, hosted by Inyo Pools. Sharkline Warranty and Consumer Support Program. Accessed 2026-10-27.
- Backyard Leisure, hosted by Pool Nation. Backyard Leisure Warranty terms and conditions. Accessed 2026-10-27.
- Embassy PoolCo, hosted by Pool Nation. Embassy PoolCo 20 year limited warranty (Skyline). Accessed 2026-10-27.
- Lomart, hosted by Pool Nation. Lomart 35 year limited warranty (Grey Mist II). Accessed 2026-10-27.
- Pro Pools (host). Round Above Ground Pool Installation Instructions (Islamorada). Accessed 2026-10-27.
- Imperial Pools. Pearl/Java Round Installation Manual (06.2023). Accessed 2026-10-27.
- Latham Pool Products. 52 in Bar Top On Ground Pool System General Installation Guide (2015). Accessed 2026-10-27.
- Aquasport (dealer-hosted). Basic Installations procedure for Aquasport 52 Pool. Accessed 2026-10-27.
- Hydra Pools. Hydra Pools Semi-Inground Pool Instructions. Accessed 2026-10-27.
- Pro Pools. The Funtastic Pool product guide. Accessed 2026-10-27.
- ICC Evaluation Service. ICC-ES Evaluation Report ESR-2014 (effective November 2025). Accessed 2026-10-27.
- Latham Pool Products. Semi-Inground Pools. Accessed 2026-10-27.
- The Pool Factory. Semi Inground Pools collection. Accessed 2026-10-27.
- The Pool Factory. How deep can the semi-inground pools be installed?. Accessed 2026-10-27.
- Pro Pools. HydroSphere Semi-Inground Pools listings. Accessed 2026-10-27.
- HomeGuide. How Much Does An Inground Pool Cost? (July 16, 2025). Accessed 2026-10-27.
- HomeGuide. How Much Does an Above-ground Pool Cost? (June 10, 2024). Accessed 2026-10-27.
- HomeGuide. Pool Deck Cost (Dec 22, 2025). Accessed 2026-10-27.
- Angi. How Much Does an In-Ground Pool Cost? (updated Aug 5, 2026, Wayback capture). Accessed 2026-10-27.
- Fiesta Pools & Spas. What a Semi-Inground Pool Really Costs (Aug 5, 2025). Accessed 2026-10-27.
- Royal Swimming Pools. Is a Semi-Inground Pool Worth It? (Dec 3, 2025). Accessed 2026-10-27.
- Plungie. Partial Inground Pools: Costs, Design Ideas and Installation (May 7, 2026). Accessed 2026-10-27.
- ConcreteNetwork. Concrete Pool Deck Cost (updated Feb 13, 2026). Accessed 2026-10-27.
- International Code Council via UpCodes. 2024 ISPSC Chapter 3 (Sections 305, 306). Accessed 2026-10-27.
- International Code Council via UpCodes. 2024 ISPSC Chapter 7 (Section 701.1). Accessed 2026-10-27.
- International Code Council via UpCodes. 2024 ISPSC Chapter 8 (Section 801.1). Accessed 2026-10-27.
- International Code Council via UpCodes. IRC Appendix G, AG105.2 Outdoor Swimming Pool (Philadelphia Residential Code 2018). Accessed 2026-10-27.
- International Code Council via UpCodes. 2021 IRC Chapter 1 (R105.2). Accessed 2026-10-27.
- International Code Council via UpCodes. 2021 IRC Chapter 3 (R312). Accessed 2026-10-27.
- U.S. Consumer Product Safety Commission. Safety Barrier Guidelines for Residential Pools (Publication 362). Accessed 2026-10-27.
- Common Ground Alliance (call811.com). What is 811?. Accessed 2026-10-27.
- City of Akron. How to calculate the gallons in a swimming pool. Accessed 2026-10-27.
- U.S. Geological Survey. Water Density. Accessed 2026-10-27.
- City of San Diego. Information Bulletin 501 (pool fees). Accessed 2026-10-27.
- City of Chandler. Development Department Fee Schedule (April 2026). Accessed 2026-10-27.
- Arizona State Legislature. A.R.S. 36-1681 Pool enclosures. Accessed 2026-10-27.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.