Skip to content
Backyard hot tub with jets churning the water on an overcast afternoon
Hot tub care: troubleshooting

Hot Tub Jets Not Working: Symptom, Cause and Fix from 7 Maker Manuals

Hot tub jets not working usually means an airlock after a refill, low water, a dirty filter, or closed jets and air controls. Fix those first; a humming or silent pump points to the motor or controls.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓14 symptoms mappedEach symptom tied to the cause and fix printed in Jacuzzi, Sundance, Hot Spring, Caldera, Bullfrog, Master Spas or Hydropool manuals.
  • ✓Airlock purgeThe 30 second hose purge, the pump union bleed and the 2 minute dry-run limit, step by step.
  • ✓Dated costsJets repair $100 to $1,000 (Fixr, Jan 2025); pump parts $369.95 to $389.95 (Nov 2026).
Quick answer
Fill to 1 to 1.5 inches above the highest jet, clean the filter, and open every jet face, air control and diverter. If the tub was just refilled, purge the airlock with a hose in the filter wall fitting for 30 seconds. A humming, silent or hot pump needs a technician.
30 seconds
Hose purge
Source: Jacuzzi 2025
2 minutes
Max dry run
15 to 20 minutes
Jet timer
$100 to $1,000
Typical repair

Key takeaways

  • Every jets section in the 7 manuals we read starts with the same three checks: water level, filter and closed jets or air controls (Jacuzzi 15.4).
  • An airlock after a refill is the classic cause of a running pump with no water at the jets; Master Spas says airlock service is not covered by its warranty.
  • Jacuzzi and Sundance purge air with a garden hose sealed into the filter wall fitting for 30 seconds.
  • Bullfrog says never let a pump run without water at the jets for more than 2 minutes; Hydropool sets 5 minutes as the hard limit.
  • Jets that shut off after 15 minutes (Master Spas, Caldera) or 20 minutes (Sundance) are on a built-in timer, not broken.
  • Fixr (Jan 2025) puts a jets-not-working repair at $100 to $1,000 and a pump replacement at $250 to $1,000.

Why are my hot tub jets not working?

In order of likelihood: an airlock after a refill, low water, a dirty filter, closed jets or air controls, a diverter set to one side, or a jet timer that ran out. Only after those does the pump, its capacitor or the control board come into play. The table maps 14 symptoms to the cause and fix printed in 7 owner’s manuals.

Hot tub jets not working: symptom, cause and fix from 7 maker manuals
SymptomMost likely causeFixManual that prints it
Pump runs or hums after a refill, no water from any jetAirlock in the pumpPurge the air (steps below): hose in the filter wall fitting or loosen the pump discharge unionJacuzzi 15.3; Sundance 14.3; Caldera; Master Spas; Hydropool
All jets weak or surgingWater level too lowFill to the maker's level: 1 in above the highest jet (Caldera), about 1.5 in (Hot Spring)Caldera; Hot Spring
All jets weak, water hazyDirty filter cartridgeClean or replace the cartridgeHydropool; Jacuzzi 15.4; Bullfrog
Jets run but feel flat, no bubblesAir controls closedTurn the air control knobs to onJacuzzi 15.4; Sundance 14.4; Caldera; Master Spas
Some jets dead, others strongJet faces closed or a diverter set to one sideOpen each jet face; set the diverter to the middle or the seats you wantJacuzzi 15.3; Caldera diverter note; Bullfrog
One bank of jets never startsSecond pump not switched onPress Jets 2 or Aux; check that pump separatelyJacuzzi 15.4; Master Spas
Specific seat jets off (Hot Spring)COMFORT CONTROL lever closedOpen the leverHot Spring
Jets stop after 15 or 20 minutesBuilt-in jet timerPress the jets button againMaster Spas 15 min; Sundance 20 min; Caldera 15 min soak timer
Pump stops on its own and restarts minutes laterMotor thermal overloadLet it cool; Caldera says up to one hourMaster Spas; Caldera; Hot Spring
Single jet weak or spittingJet orifice blockedRemove the jet face and clean the orificeCaldera
Weak jets, suction fitting coveredBlocked suction or skimmer basketClear debris from suction covers and basketBullfrog; Caldera
Pump silent, panel works, jet symbol onPump motor or control switch failurePower off; call the dealerCaldera; Master Spas; Bullfrog
Pump hums but will not spinFailed capacitor, jammed impeller or corrosionPower off; book a technicianJacuzzi jets guide
Nothing runs, panel darkTripped breaker or GFCIReset after 30 seconds; if the GFCI trips again, call an electricianJacuzzi 15.2; Caldera

Sources: Jacuzzi J-300 2025; Sundance 780 2025; Hot Spring Highlife 2026; Caldera Paradise 2025; Bullfrog 2018; Master Spas Getaway 2025; Hydropool Serenity 2024 owner’s manuals, accessed Nov 8 to 9, 2026. Capacitor row: Jacuzzi jets guide. Download CSV

Key numbers for hot tub jet troubleshooting
NumberValueSource
Hose purge into the filter wall fitting30 secondsJacuzzi 2025; Sundance 2025
Longest pump burst while priming5 to 10 secondsJacuzzi 2025; Sundance 2025
Longest run without water at the jets2 minutes (Bullfrog); 5 minutes max (Hydropool)Bullfrog 2018; Hydropool 2024
Power cycles to help primingNo more than 5Bullfrog 2018; Hydropool 2024
Water level1 to 1.5 in above the highest jetCaldera 2025; Hot Spring 2026
Jet timer15 minutes (Master Spas, Caldera); 20 minutes (Sundance)Owner's manuals
Jets not working repair$100 to $1,000Fixr, Jan 2025

Sources: Jacuzzi J-300 2025; Sundance 780 2025; Hot Spring Highlife 2026; Caldera Paradise 2025; Bullfrog 2018; Master Spas Getaway 2025; Hydropool Serenity 2024 owner’s manuals, accessed Nov 8 to 9, 2026. Cost: Fixr, Jan 2025. Download CSV

Check order for jets that will not run: power, pump sound, water at the jets, then all jets weak or only some. Compiled from 7 owner's manuals; the decision table at the end holds the same logic.
Check order for jets that will not run: power, pump sound, water at the jets, then all jets weak or only some. Compiled from 7 owner’s manuals; the decision table at the end holds the same logic.

How do you clear an airlock in a hot tub?

Turn the pump on in 5 to 10 second bursts; if no water comes, cut power, pull the filter and run a garden hose sealed into the filter wall fitting for 30 seconds (Jacuzzi, Sundance). If that fails, loosen the union on the pump’s discharge side until water weeps out, tighten it and restart (Master Spas, Hydropool, Caldera).

  1. Let priming mode runPower up and press each jets button; Bullfrog’s priming mode lasts 4 to 5 minutes and Hydropool’s shows RUN PMPS PURG AIR for 4 minutes.
  2. Watch the 15 second markHydropool says water should circulate within 15 seconds; if not, the pump likely holds trapped air.
  3. Pulse the pumpPress JETS 1 several times, never running the motor more than 5 to 10 seconds at a time (Jacuzzi 15.3).
  4. Hose purgePower off, remove the cartridge, seal a garden hose into the filter wall fitting with a rag and run water for 30 seconds; reinstall the filter (Jacuzzi 15.1).
  5. Bleed the unionPower off at the breaker, loosen the union on the pump discharge until water leaks, then hand-tighten (Master Spas; Caldera).
  6. Power cycle, 5 times at mostTurning the pump off and on can help it prime; Bullfrog and Hydropool cap this at 5 tries.
  7. Stop and callIf the pump will not prime, shut the power off and call for service; running dry past 2 minutes (Bullfrog) risks pump damage and an overheat.
Where air gets trapped and the three purge points the manuals use: the filter wall fitting (30 second hose purge), the pump discharge union and Bullfrog's air bleed line.
Where air gets trapped and the three purge points the manuals use: the filter wall fitting (30 second hose purge), the pump discharge union and Bullfrog’s air bleed line.
Airlock methods and limits, as printed in 7 owner's manuals
Maker manualAirlock method printedLimit printed
Jacuzzi J-300 (2025)Press JETS 1 in bursts; power off; remove the filter; hose sealed with a rag into the filter wall fitting for 30 secondsNever run the motor more than 5 to 10 seconds at a time
Sundance 780 (2025)Same as Jacuzzi: hose into the filter cartridge wall fitting for 30 seconds5 to 10 second bursts
Master Spas Getaway (2025)Loosen the pump union on the discharge side until water leaks, then tightenAirlock service is not covered by warranty
Hydropool Serenity (2024)Power off, loosen the discharge-side union, power on; cycle the pump off and onStop if not primed in 2 minutes; never past 5 minutes; cycle no more than 5 times
Caldera Paradise (2025)Power off at the breaker, loosen the union on top of the pump, hand-tighten, test for leaksNone printed
Bullfrog (2018)Remove the air bleed line clamp and line from the pump until water flows; or power cycle to restart priming modeNo more than 2 minutes unprimed; priming mode lasts 4 to 5 minutes; cycle no more than 5 times
Hot Spring Highlife (2026)Run the jet pumps on high for one minute after a fill to purge air from the heaterPrimed when jets are strong and non-surging

Sources: Jacuzzi J-300 2025; Sundance 780 2025; Hot Spring Highlife 2026; Caldera Paradise 2025; Bullfrog 2018; Master Spas Getaway 2025; Hydropool Serenity 2024 owner’s manuals, accessed Nov 8 to 9, 2026. Download CSV

Why are my hot tub jets not working after a refill?

Because air entered the pump and heater lines while the tub was empty, and filling from the open tub traps it. Caldera, Hot Spring and Master Spas all say fill through the filter compartment, and Hydropool through the skimmer, so water pushes air out from below. Then fill to 1 inch above the highest jet (Caldera) or 4 inches above the skimmer opening (Hydropool).

Water level and fill method by maker
MakerCorrect water levelFill tip printed
Caldera (2025)1 in above the highest jetFill through the filter compartment
Hot Spring (2026)About 1.5 in above the top of the highest jetRefill through the filter compartment
Jacuzzi (2025), Sundance (2025)Above all jets, below the lowest pillowHose in the filter well if an airlock forms
Master Spas (2025)At the minimum level label, at least 1 in above the filters or filter housing openingFill through the filter area
Hydropool (2024)About 4 in above the top of the skimmer openingFill through the skimmer opening; all jets open

Sources: Caldera Paradise 2025; Hot Spring Highlife 2026; Jacuzzi J-300 2025; Sundance 780 2025; Master Spas Getaway 2025; Hydropool Serenity 2024. Download CSV

Hot Spring adds a check after every fill: run the jet pumps on high for 1 minute, and priming is complete when the jets are strong and non-surging. The full drain and refill routine, including where the water can go, is in our guide on how to drain a hot tub.

Why are only half of the jets working in my hot tub?

Usually a diverter valve turned to one side, closed jet faces or a second pump that is off. Caldera says its spa is not designed to run every jet at full power with the diverter at mid, so close unused jets to boost the rest. If one whole bank never starts, press Jets 2 or Aux and prime that pump separately.

When only some hot tub jets work
What you seeCauseWhat to doSource
One side of the tub weak, other side strongDiverter valve turned toward one sideTurn it back to mid; at mid, close unused jets to boost the restCaldera Paradise 2025
One pump's seats deadPump 2 off or airlockedPress Jets 2 or Aux; prime that pump separatelyJacuzzi 15.4; Bullfrog priming notes
Scattered single jets deadJet faces rotated closedRotate each face to full openJacuzzi 15.3; Master Spas
Jets on one seat only, no air mixAir control for that zone closedOpen that air controlSundance 14.4; Caldera
Bullfrog JetPak seat deadJetPak valve closedOpen the valveBullfrog 2018

Sources: Caldera Paradise 2025; Jacuzzi J-300 2025; Sundance 780 2025; Master Spas Getaway 2025; Bullfrog 2018. Download CSV

Diverters that are hard to turn usually hold sand or grit, and Caldera says to clean and lubricate them per its maintenance steps. Fixr puts a diverter valve replacement at $100 to $200 (Jan 2025) if the valve body is cracked.

Why are my hot tub jets weak?

Low water, a dirty filter and closed air controls cause most weak jets. Hot Spring says weak or surging jets indicate low water or clogged cartridges, and Hydropool lists reduced jet power as a sign the filter needs cleaning every 2 to 4 weeks. A single weak jet usually has a blocked orifice that Caldera says to clean.

Work through 3 free fixes before anything else. Top up to the level in the table above, rinse the cartridge (our hot tub filter cleaning guide lists each maker’s interval), and open every air control. Bullfrog‘s 2018 manual adds a fourth: clear debris from the suction fittings, since a blocked suction starves every jet on that pump.

Weak or surging jets usually trace to water level: Caldera keeps it 1 inch and Hot Spring about 1.5 inches above the highest jet.
Weak or surging jets usually trace to water level: Caldera keeps it 1 inch and Hot Spring about 1.5 inches above the highest jet.

Why do hot tub jets turn off after 15 minutes?

A built-in timer. Master Spas shuts high speed off after 15 minutes, Caldera’s Soak Timer ends jets at 15 minutes and Sundance jets run 20 minutes per press. A pump that stops early and restarts minutes later has usually tripped its thermal overload, which Caldera says resets on its own after cooling for up to one hour.

Jet timers and motor overheat behavior by maker
MakerJets or high speed turn off afterMotor overheat behavior
Master Spas Getaway (2025)15 minutes (high speed and Aux)Pump can shut itself off to cool for several minutes after repeated high-speed runs
Sundance 780 (2025)20 minutes per press of Jets 1 or Jets 2Not printed
Caldera Paradise (2025)15 minute Soak Timer turns jets offMotor overload resets on its own; let it cool for one hour
Hydropool Serenity (2024)High speed returns to low after 15 minutesRunning unprimed past 5 minutes can trigger an overheat condition
Hot Spring Highlife (2026)Jet screen returns home after 45 seconds; jets keep runningCirculation pump thermal cut-off resets when cool and power is reapplied

Sources: Master Spas Getaway 2025; Sundance 780 2025; Caldera Paradise 2025; Hydropool Serenity 2024; Hot Spring Highlife 2026. Download CSV

Master Spas notes that running the pumps on high again and again past the 15 minute timeout in warm weather can overheat the motor until it shuts itself off. If the cutout happens on every soak in mild weather, ask a technician to check the motor’s amp draw and the equipment bay vent.

How do you know if the hot tub pump is the problem?

The pump is the likely fault when you can hear it hum but it will not spin, when it is silent while the jet symbol shows on, or when it smells hot or grinds. Jacuzzi lists a failed capacitor, a jammed impeller or corrosion for a humming pump. Bullfrog’s 2018 manual says a burning smell or excessive noise means a defective motor.

Before you buy a pump, rule out the airlock and the GFCI, and confirm the control is sending power to it. A 2 HP 240 V Waterway Executive pump listed at $389.95 and a 1.5 HP 120 V version at $369.95 on Spa Depot on November 9, 2026, before labor; match the horsepower, voltage, frame and port size printed on your old pump’s label. Check the serial number against CPSC notices too: our pool product recalls registry lists 83 pool and spa recalls from December 2001 to October 2026.

How much does it cost to fix hot tub jets?

Between $100 and $1,000 for a jets-not-working repair, per Fixr’s January 2025 national figures. A jet replacement runs $50 to $200, a diverter valve $100 to $200 and a pump repair $200 to $500, while a new pump or motor runs $250 to $1,000 installed. An airlock or filter fix costs nothing but time.

Hot tub jet repair costs and pump part prices, dated
Repair or partCostSource and date
Fix jets not working (all causes)$100 to $1,000Fixr, updated Jan 31, 2025
Jet replacement$50 to $200Fixr, updated Jan 31, 2025
Diverter valve replacement$100 to $200Fixr, updated Jan 31, 2025
Pump repair$200 to $500Fixr, updated Jan 31, 2025
Pump or motor replacement$250 to $1,000Fixr, updated Jan 31, 2025
Circuit board replacement$350 to $1,000Fixr, updated Jan 31, 2025
Diagnostic visit / labor$100 to $200 / $75 to $125 per hourFixr, updated Jan 31, 2025
Part: 2 HP Waterway Executive pump, 240 V (BX4104-S2)$389.95Spa Depot listing, Nov 9, 2026
Part: 1.5 HP Waterway Executive pump, 120 V (BX4102-S2)$369.95Spa Depot listing, Nov 9, 2026

Sources: Fixr, Hot Tub Repair Cost, updated Jan 31, 2025; Spa Depot BX4104-S2 and BX4102-S2 listings, Nov 9, 2026. Download CSV

Hot tub jet repair costs by job, USInstalled cost range, US dollars, Fixr (Jan 2025)
Hot tub jet repair costs by job, USRange chart: jet replacement $50 to $200, diverter valve $100 to $200, pump repair $200 to $500, pump or motor replacement $250 to $1,000.$0$250$500$750$1,000Jet replacement: $50 to $200Jet replacementDiverter valve: $100 to $200Diverter valveDiagnostic visit: $100 to $200Diagnostic visitPump repair: $200 to $500Pump repairPump or motor replacement: $250 to $1,000Pump or motor replacementJets not working, all causes: $100 to $1,000Jets not working, all causes

Pump parts alone listed at $369.95 to $389.95 on Spa Depot, Nov 9, 2026.

Source: Fixr, Hot Tub Repair Cost, updated Jan 31, 2025. Download chart data (CSV)

Repair math changes with the tub’s age. A $1,000 pump job on a 12 year old tub buys less remaining life than on a 4 year old one, which our hot tub lifespan guide works through with DOE survival data. New-tub prices by type are in our hot tub cost guide.

What should you do when your hot tub jets stop working?

Match your situation to a row. A refill with no water at the jets is an airlock; weak jets everywhere are level, filter or air controls; dead seats are diverters or a second pump; a timed stop is normal. A humming, silent or hot pump, or a pump that will not prime after 5 tries, needs a technician.

What to do for each jets problem
If your situation isDo thisWhy (source)
Just refilled, pump runs, no water at the jetsPurge the airlock; stop the pump within 2 minutes if it will not primeBullfrog 2 minute limit; Jacuzzi and Sundance hose purge
All jets weakTop up water, clean the filter, open the air controlsCaldera, Hot Spring, Jacuzzi troubleshooting tables
Only one side or one seat worksCheck the diverter, jet faces, Jets 2 buttonCaldera diverter note; Jacuzzi 15.4
Jets stop after 15 or 20 minutesNormal timer; press the button againMaster Spas, Caldera, Sundance
Pump stops mid-soak, restarts laterLet it cool; call if it repeats dailyMaster Spas thermal cutout; Caldera one hour reset
Pump hums, will not spin, or smells hotPower off and book a technicianJacuzzi jets guide; Bullfrog: defective motor
Pump will not prime after 5 power cyclesPower off and call for serviceBullfrog 2018; Hydropool 2024
Repair quote above about $1,000 on an old tubCompare it with replacement before you approve itFixr ranges; our hot tub lifespan guide

Sources: Jacuzzi J-300 2025; Sundance 780 2025; Hot Spring Highlife 2026; Caldera Paradise 2025; Bullfrog 2018; Master Spas Getaway 2025; Hydropool Serenity 2024 owner’s manuals, accessed Nov 8 to 9, 2026. Costs: Fixr, Jan 2025. Download CSV

If the jets work but the water stays cold, the same flow problems trip the heater; our hot tub not heating guide lists the flow codes from 7 maker manuals. Routine filter and water care that prevents most of these calls is in our hot tub maintenance schedule.

How we compiled this

We read the jets, priming and troubleshooting sections of 7 owner’s manuals (Jacuzzi, Sundance, Hot Spring, Caldera, Bullfrog, Master Spas, Hydropool), Jacuzzi’s jets guide, Fixr’s January 2025 repair costs and 2 Spa Depot pump listings, in November 2026. We did not test any tub. Forum threads in the search results were read for question wording only.

Frequently Asked Questions

What are the possible reasons why my hot tub jets are not working?

An airlock after a refill, low water, a dirty filter, closed jets or air controls, a diverter turned to one side, a jet timer that ran out, or a pump fault. Jacuzzi‘s manual checks jets open, pump 1 on, air controls on and the filter, in that order. Pump faults such as a failed capacitor come last.

How do you clear an airlock in a hot tub?

Pulse the pump in 5 to 10 second bursts, then cut power, remove the filter and run a hose sealed into the filter wall fitting for 30 seconds (Sundance). If that fails, loosen the pump’s discharge union until water weeps out and tighten it. Stop after 2 minutes without water at the jets.

How do you fix spa jets not working?

Start free: fill to 1 to 1.5 inches above the highest jet, clean the filter, open every jet face and air control, and center the diverter. Purge any airlock. If the pump hums, stays silent or smells hot, power off and book a technician; Fixr puts the repair at $100 to $1,000 (Jan 2025).

Why are only half of the jets working my hot tub?

A diverter valve set to one side, closed jet faces or a second pump that is off or airlocked. Caldera says its spa cannot run every jet at full power with the diverter at mid. Press Jets 2 or Aux; if that pump runs without water, prime it separately.

Why are my hot tub jets weak?

Low water, a clogged filter or closed air controls in most cases. Hot Spring ties weak or surging jets to low water or dirty cartridges, and Hydropool lists reduced jet power as a cleaning signal every 2 to 4 weeks. A single weak jet usually needs its orifice cleaned.

Why are my hot tub jets not working after a refill?

Air is trapped in the pump. Fill through the filter compartment next time, as Caldera and Hot Spring direct, then run the jets on high for 1 minute. If no water flows within 15 seconds, purge the air at the filter wall fitting or the pump union.

Sources

  1. Jacuzzi Hot Tubs. J-300 Collection Owner's Manual, Rev E (2025). Accessed 2026-11-08.
  2. Sundance Spas. 780 Series Owner's Manual, 2025 Rev A. Accessed 2026-11-08.
  3. Hot Spring Spas (Watkins Wellness). Highlife Collection Owner's Manual, 2026. Accessed 2026-11-08.
  4. Caldera Spas (Watkins Wellness). Paradise Series Owner's Manual, 2025. Accessed 2026-11-08.
  5. Bullfrog Spas. Owner's Manual, 2018 (rev 3.1.8). Accessed 2026-11-08.
  6. Master Spas. 2025 Getaway Spas Owner's Manual. Accessed 2026-11-08.
  7. Hydropool. Serenity Hot Tubs Owner's Manual, 2024. Accessed 2026-11-08.
  8. Jacuzzi. Hot Tub Jets Not Working (jets guide). Accessed 2026-11-09.
  9. Fixr. Hot Tub Repair Cost (updated Jan 31, 2025). Accessed 2026-11-08.
  10. Spa Depot (retailer). 2 HP Waterway Executive Spa Pump, 240 V, BX4104-S2. Accessed 2026-11-09.
  11. Spa Depot (retailer). 1.5 HP Waterway Executive Spa Pump, 120 V, BX4102-S2. Accessed 2026-11-09.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.