Skip to content
Backyard pool deck with a coiled garden hose and an empty bucket in morning light
Pool care: filters

How to Clean a Pool Filter: Cartridge Hosing, Degreasing, Acid Soaks and DE Grids

How to clean a pool filter: at about 10 psi over the clean start, hose each cartridge or DE grid top to bottom, soak out oils for at least 1 hour, and acid soak only after degreasing.

Free Pool Quote Match

Tell us about your pool project. We match you with licensed local pros who cover your area.

Step 1 of 3: Your project

Free for homeownersNo obligationAbout 60 seconds

  • ✓Gauge, not calendarPentair cleans Clean & Clear Plus cartridges at about 10 psi over the starting pressure.
  • ✓Degrease before acidPentair and the 2024 Model Aquatic Health Code both bar acid before the oils are out.
  • ✓Replace on pressureHayward replaces SwimClear cartridges that restart more than 6 psi above new.
Quick answer
Turn the pump off at the breaker and open the air relief valve until the gauge reads 0 psi. Hose each cartridge top to bottom at a 45 degree angle. For oils, soak at least 1 hour in filter cleaner or 1 cup TSP per 5 gallons. Acid soak (1 part muriatic acid to 20 parts water) only after degreasing.
About 10 psi over start
Clean at
1 cup TSP per 5 gal, 1 hour+
Degrease soak
1:20, 10 min per half
Acid mix
6 psi over new after cleaning
Replace when

Key takeaways

  • Pentair’s Clean & Clear Plus guide says to clean the cartridges at about 10 psi over the Original Starting Pressure; Hayward’s SwimClear manual uses 7 to 10 psi and Unicel 8 psi (Pentair cartridge cleaning guide).
  • The 2024 Model Aquatic Health Code, section 5.7.2.4.3.3, bans pressure washers on cartridges and calls for an overnight degreasing soak in a labeled cleaner, 1 cup TSP or 1 cup automatic dishwasher detergent per 5 gallons (CDC MAHC 2024).
  • Pentair’s acid soak is 1 part muriatic acid to 20 parts water for 10 minutes per half, and only after every trace of oil and cleaner is rinsed out (Pentair).
  • DE grids get recoated after cleaning at 1.0 lb per 10 sq ft on Pentair FNS Plus and Quad DE filters and 1.25 lb per 10 sq ft on Hayward Pro-Grid filters (Pentair FNS Plus guide; Hayward Pro-Grid manual).
  • Hayward says to replace SwimClear cartridges once a cleaned set restarts more than 6 psi above its new-cartridge reading (Hayward SwimClear manual).
  • Hosing off a cartridge uses 20 to 30 gallons of water against hundreds of gallons for a backwash, according to Fort Worth Water.

When should you clean a pool filter?

Clean a pool filter when its pressure gauge climbs a set amount over the reading taken right after the last cleaning: about 10 psi for Pentair Clean & Clear Plus cartridges, 7 to 10 psi for Hayward SwimClear, 8 psi under Unicel’s rule and 8 to 10 psi for Hayward DE and sand filters. The calendar is a weak signal; the gauge is the maker’s trigger.

Cleaning triggers by filter, from each maker's manual
Filter (type)Clean or backwash when the gauge readsWhat the manual says to doSource
Pentair Clean & Clear Plus CCP320, CCP420, CCP520 (cartridge)About 10 psi over the Original Starting PressureOpen the filter and hose the cartridgesPentair cartridge cleaning guide
Hayward SwimClear C2030 to C7030 (cartridge)7 to 10 psi over the starting pressureClean or replace the cartridge elementsHayward SwimClear manual ISC2031EF Rev B
Unicel replacement cartridges (cartridge)8 psi over the new-cartridge start pressureClean the elementUnicel maintenance FAQ
Hayward Pro-Grid DE2420 to DE7220 (DE grids)8 to 10 psi over the pre-coat pressureBackwash, then add fresh DEHayward Pro-Grid manual ISDE2423EF Rev E
Pentair FNS Plus FNSP36, FNSP48, FNSP60 (DE grids)About 10 psi over the Original Starting PressureBackwash; hose the grids by hand if pressure stays highPentair FNS Plus guide (2025)
Hayward ProSeries S144T to S360T2 (sand)8 to 10 psi over the clean pressureBackwash about 2 minutes, rinse 1/2 to 1 minuteHayward ProSeries manual IS210TS Rev A
Any filter on a variable speed pumpCompare readings at the same pump RPMRecord the Original Pump RPM next to the starting pressurePentair cartridge cleaning guide; FNS Plus guide

Sources: Pentair Clean & Clear Plus cleaning guide; Hayward SwimClear manual; Unicel maintenance FAQ; Hayward Pro-Grid manual; Pentair FNS Plus guide (2025); Hayward ProSeries manual. Download CSV

Gauge rise that triggers a filter cleaning, by maker manual (psi over the clean starting pressure)Low and high end of each published trigger; a single value shows as a point
Gauge rise that triggers a filter cleaning, by maker manual (psi over the clean starting pressure)Range chart: Hayward SwimClear cartridges are cleaned at 7 to 10 psi over start, Unicel at 8 psi, Pentair Clean & Clear Plus at 10 psi, Hayward Pro-Grid DE at 8 to 10 psi, Pentair FNS Plus DE at 10 psi and Hayward ProSeries sand at 8 to 10 psi.02.557.510Hayward SwimClear (cartridge): 7 to 10Hayward SwimClear (cartridge)Unicel cartridges: 8 to 8Unicel cartridgesPentair Clean & Clear Plus (cartridge): 10 to 10Pentair Clean & Clear Plus (cartridge)Hayward Pro-Grid (DE): 8 to 10Hayward Pro-Grid (DE)Pentair FNS Plus (DE): 10 to 10Pentair FNS Plus (DE)Hayward ProSeries (sand): 8 to 10Hayward ProSeries (sand)

Every maker measures from the reading taken right after the last cleaning, not from zero.

Source: Source: Hayward SwimClear, Pro-Grid and ProSeries manuals; Pentair Clean & Clear Plus cleaning guide and FNS Plus guide (2025); Unicel maintenance FAQ. Accessed October 2026.. Download chart data (CSV)

Why does the starting pressure matter? Every trigger is a rise over the clean reading, not an absolute number, so write the clean reading on the filter right after each cleaning. Pentair’s 2025 Clean & Clear Plus guide adds that on a variable speed pump the Original Starting Pressure depends on pump RPM, so it asks owners to record the RPM as well (Pentair install guide). Our variable speed pool pump guide covers how those speed programs work.

Does a filter need cleaning on a schedule? Not by the manuals. Simple Green, which sells a cleaner, suggests once a month in summer and every other month in winter, but Pentair ties cleaning to the gauge or a clear drop in flow, and the 2024 Model Aquatic Health Code (5.7.2.4.3) sets public-pool cartridge changes at the pressure rise the filter maker recommends. Unicel warns that cleaning too often also hurts, because a cartridge uses the dirt it holds to trap finer particles.

Two events push the gauge up fast: vacuuming through the filter and clearing an algae bloom. Hayward’s SwimClear manual says vacuuming can go straight into the filter, followed by a cartridge cleaning if required; our how to vacuum a pool guide covers when to switch to the WASTE setting instead. Spring pollen is a third; our guide to pollen in pool water covers skimmer socks, clarifier doses and peak weeks by region.

How do you clean a cartridge pool filter step by step?

Shut the pump off at the breaker, bleed the pressure to 0 psi, drain the tank, lift out the cartridges and hose each one top to bottom at a 45 degree angle. Degrease if oils are present, rinse, reinstall and restart with the air relief valve open. Pentair says the whole job takes at least 30 minutes on a Clean & Clear Plus.

  1. Kill power and bleed pressureTurn the pump and any timer or automation off, then switch off the breaker. Open the manual air relief valve a 1/4 turn and stand clear until the gauge reads 0 psi (Pentair).
  2. Drain and open the tankOpen the drain plug at the bottom. On a Clean & Clear Plus, loosen the clamp barrel nut with a 7/8-inch socket, lift the lid straight up and set the O-ring somewhere clean (Pentair).
  3. Remove the cartridgesTake off the top manifold and lift each cartridge out separately. Clean the pump strainer basket while the system is open (Pentair).
  4. Hose every pleatUse a straight-flow garden hose nozzle at a 45 degree angle and wash from top to bottom between the pleats. Hayward and the 2024 Model Aquatic Health Code both rule out a pressure washer, which can damage the media.
  5. Degrease when oils are presentSoak at least 1 hour in a commercial filter cleaner, 1 cup TSP per 5 gallons or 1 cup dishwasher detergent per 5 gallons (Pentair); MAHC 2024 calls for an overnight soak. Rinse until no cleaner remains.
  6. Wash the tank and check sealsHose out the tank and bottom manifold through the open drain, check that the bottom gasket sits evenly and that the tank O-ring is clean (Pentair).
  7. Reassemble and restartReinstall the cartridges and lid, tighten until the clamp spring coils touch, close the drain, open the air relief valve and start the pump. A solid stream of water should appear within 30 seconds; then close the valve (Pentair).
  8. Write down the new startRecord the new starting pressure, plus the pump RPM on a variable speed pump. The next cleaning falls about 10 psi above it.
Pentair's own cleaning steps: hose at a 45 degree angle, soak oily cartridges at least one hour in filter cleaner, 1 cup TSP or 1 cup dishwasher detergent per 5 gallons, and rinse before any acid (Pentair Clean & Clear Plus Cartridge Cleaning Guide, page 3; accessed 2026-10-26).
Pentair’s own cleaning steps: hose at a 45 degree angle, soak oily cartridges at least one hour in filter cleaner, 1 cup TSP or 1 cup dishwasher detergent per 5 gallons, and rinse before any acid (Pentair Clean & Clear Plus Cartridge Cleaning Guide, page 3; accessed 2026-10-26).

Which pool cartridge filter cleaner should you use?

Use a cleaner whose label covers cartridges, or the soaks filter makers print themselves: 1 cup TSP or 1 cup automatic dishwasher detergent per 5 gallons (Pentair; MAHC 2024). Labels differ 36-fold in contact time, from a 10-minute Strip Kwik spray to a 6-hour minimum Filter Perfect soak, so follow the directions on the bottle you bought.

Cartridge cleaners and home soaks compared: mix, contact time and the limits on each label
Cleaner or soakMixContact timeUse it forDo notSource
Natural Chemistry Filter Perfect (enzyme, acid free)1 bottle (1 L, 33.9 oz) in 5 to 10 gallons of waterAt least 6 hours, preferably overnight; let the cartridge dry before reinstallingCartridges and DE gridsSkip the thorough rinseNatural Chemistry label directions
BioGuard Strip Kwik (pH above 11.9)Full strength in a spray bottle, or 1 part product to 3 parts waterSpray: 10 minutes, then rinse 5 minutes. Soak: 1 hourGrease and oil on cartridges and DE elementsUse on SoftSwim or other biguanide systemsBioGuard product sheet
Simple Green All-Purpose Cleaner1/4 cup in 2 1/2 cups of water; equal parts for a first cleaning10 minutes, then scrub gently and rinseCartridgesNot statedSimple Green pool filter page
Trisodium phosphate (TSP)1 cup per 5 gallons of waterAt least 1 hour (Pentair); overnight (MAHC 2024)Oils from sweat and sunscreenUse before stripping biguanide filmPentair cleaning guide; MAHC 2024 5.7.2.4.3.3.4; Unicel
Automatic dishwasher detergent1 cup per 5 gallons of waterAt least 1 hour (Pentair); overnight (MAHC 2024)Oils from sweat and sunscreenSubstitute hand dish soap (not listed by Pentair or MAHC)Pentair cleaning guide; MAHC 2024 5.7.2.4.3.3.4
Muriatic acid1 part acid to 20 parts water10 minutes per half, or until bubbling stopsCalcium carbonate, iron and mineral scaleUse before degreasing, or mix with chlorinePentair cleaning guide; Unicel; MAHC 2024 5.7.2.4.3.3.5
Household bleach1 quart per 5 gallons of water1 hour, then rinseSanitizing a degreased cartridge after algae or contaminationCombine with acidMAHC 2024 5.7.2.4.3.3.7; Unicel

Sources: Natural Chemistry Filter Perfect label; BioGuard Strip Kwik product sheet; Simple Green; Pentair cleaning guide; CDC MAHC 2024; Unicel. Download CSV

Minimum contact time on each cartridge cleaner label or maker recipe (minutes)MAHC 2024 calls for an overnight degreasing soak; overnight is not plotted
Minimum contact time on each cartridge cleaner label or maker recipe (minutes)Bar chart of minimum contact times: Strip Kwik spray 10 minutes, Simple Green spray 10, muriatic acid 20 in two halves, TSP or dishwasher detergent 60, Strip Kwik soak 60, bleach sanitize 60, Natural Chemistry Filter Perfect 360 minutes.Strip Kwik spray: 10Strip Kwik spray10Simple Green spray: 10Simple Green spray10Muriatic acid 1:20: 20Muriatic acid 1:2020TSP or detergent soak: 60TSP or detergent soak60Strip Kwik soak 1:3: 60Strip Kwik soak 1:360Bleach sanitize (MAHC): 60Bleach sanitize (MAHC)60Filter Perfect soak: 360Filter Perfect soak360

Filter Perfect at 360 minutes is 36 times the 10-minute spray minimum.

Source: Source: BioGuard Strip Kwik product sheet; Simple Green pool filter page; Pentair Clean & Clear Plus cleaning guide; CDC MAHC 2024 5.7.2.4.3.3; Natural Chemistry Filter Perfect label. Accessed October 2026.. Download chart data (CSV)

Worked arithmetic: how much TSP, detergent, bleach, acid or Filter Perfect to add for common container sizes
Container water volume (gallons)TSP or dishwasher detergent at 1 cup per 5 gal (cups)Household bleach at 1 quart per 5 gal (quarts)Muriatic acid at 1 part to 20 parts water (quarts)Natural Chemistry Filter Perfect (1 L bottles)
51111
102221
204442.0 to 4.0
326.46.46.43.2 to 6.4

Rates from the Pentair cleaning guide, MAHC 2024 5.7.2.4.3.3 and Natural Chemistry label; PC&S arithmetic (1 gallon = 4 quarts = 16 cups). Download CSV

Does a biguanide pool need a different cleaner? Yes. Unicel says the gray film that biguanide sanitizers (Baquacil, SoftSwim) leave on media must come off with the biguanide maker’s own filter cleaner first; TSP on top of that film forms a gum that cannot be removed, and the cartridge has to be replaced. BioGuard’s Strip Kwik sheet likewise says not to use it with SoftSwim or other biguanide systems.

When does a cartridge need an acid soak?

Only when mineral scale stays after degreasing. Unicel’s test: once the cartridge is degreased and rinsed, put a few drops of acid on a small patch of media; bubbling means calcium or mineral build-up and a mild acid soak, no bubbling means skip it. Pentair’s recipe is 1 part muriatic acid to 20 parts water, 10 minutes per half or until bubbling stops.

  1. Degrease and rinse firstPentair and MAHC 2024 section 5.7.2.4.3.3.5 both forbid acid before degreasing: oils left under acid permanently restrict flow and cause premature cartridge failure.
  2. Put on protectionRubber gloves, safety glasses and an N-95 dust mask (Pentair).
  3. Mix 1 to 20 in plasticIn a large plastic container, add muriatic acid to the water as close to the surface as possible. 1 quart of acid in 5 gallons of water is a 1 to 20 mix.
  4. Soak each halfBottom half in for 10 minutes or until bubbling stops, then flip the cartridge and soak the top half the same way (Pentair).
  5. Rinse and disposeHose the cartridge top to bottom at 45 degrees and dispose of the acid solution under local rules (Pentair).
What several cleaning guides say, and what the filter manual or the CDC code says instead
What a guide saysWho says itWhat the primary source saysPrimary source
Hose the cartridge with a high-pressure hoseHayward filter-types article (May 2023)Do not pressure wash the cartridge; it can damage the element. MAHC: a pressure washer shall not be usedHayward SwimClear manual; MAHC 2024 5.7.2.4.3.3.2
Clean the filter once a month in summer and every other month in winterSimple Green pool filter pageClean at about 10 psi over the Original Starting Pressure, or when flow dropsPentair cartridge cleaning guide
Soak the cartridge for a minimum of 12 hoursAtomic Filters guide (June 2026)At least 1 hour (Pentair); overnight (MAHC); at least 6 hours for Filter Perfect (label)Pentair cleaning guide; MAHC 2024; Natural Chemistry label
Add 1 to 2 pounds of DE per 10 sq ft of filter areaRoyal Swimming Pools backwash guide1.0 lb per 10 sq ft (Pentair FNS Plus and Quad DE); 1.25 lb per 10 sq ft (Hayward Pro-Grid)Pentair FNS Plus and Quad DE guides; Hayward Pro-Grid manual
Acid wash the cartridge when it looks dirtyCommon adviceAcid washing is perhaps the biggest single cause of premature cartridge failure; degrease first and acid only if a drop test bubblesUnicel maintenance FAQ

Sources: Hayward filter-types article (2023); Hayward SwimClear manual; CDC MAHC 2024; Simple Green; Pentair cleaning guide; Atomic Filters; Natural Chemistry; Royal Swimming Pools; Pentair FNS Plus; Pentair Quad DE; Hayward Pro-Grid; Unicel. Download CSV

Should a cartridge be sanitized after algae? For public pools the 2024 Model Aquatic Health Code adds a step after degreasing: soak the cartridge 1 hour in 1 quart of household bleach per 5 gallons, then rinse (section 5.7.2.4.3.3.7). Home pools are not bound by it, but it is the same step our black algae guide uses so spores do not ride back in on the filter. The same bleach soak is the filter step in our white water mold treatment, where cartridges that keep reseeding flakes get replaced.

Filters hold what swimmers shed. CDC detected E. coli in 93 of 161 filter backwash samples (58%) taken at metro-Atlanta public pools in 2012, as our pool hygiene statistics report details from the MMWR study.

How do you clean DE filter grids?

Backwash first, and open the tank only when pressure stays high after a backwash or when closing for winter (Pentair FNS Plus). Lift out the grid assembly, hose off the old DE at a 45 degree angle, check the cloth for tears, reassemble, then recoat with the label amount of DE: 3.0 to 10 lb across the Hayward and Pentair models below.

  1. Backwash, then power offHayward says to backwash before any manual cleaning. Then cut power at the breaker and open the air relief valve until the gauge reads 0 psi.
  2. Flush the old DEWith the drain plug out, Hayward recommends hosing the element cluster with a strong stream, or its EC2024 cleaning wand, to flush dirty DE out of the drain before lifting it.
  3. Hose each gridOn a Pentair FNS Plus, lift the assembly by the manifold handles, remove the grids one at a time and hose each at a 45 degree angle. Brush gently and do not pressure wash (Hayward).
  4. Inspect and reassembleTorn cloth calls for repair or replacement (Hayward). Seat the smallest grid in the SMALL GRID slot and do not overtighten the wing nuts, which Pentair warns can let DE into the pool.
  5. Recoat with DEMix the label amount with water into a thin, milky slurry and pour it into the skimmer with the pump running (Pentair Quad DE). Never run the filter more than 3 minutes without DE (Pentair).
DE charge by filter model after a cleaning, with the coffee-can count Pentair uses
Filter modelFilter area (sq ft)DE charge (lb)lb per 10 sq ft1-lb coffee cans at about 0.5 lb eachSource
Hayward Pro-Grid DE2420243.01.256.0Hayward Pro-Grid manual
Hayward Pro-Grid DE3620364.51.259.0Hayward Pro-Grid manual
Hayward Pro-Grid DE4820486.01.2512.0Hayward Pro-Grid manual
Hayward Pro-Grid DE6020607.51.2515.0Hayward Pro-Grid manual
Hayward Pro-Grid DE7220729.01.2518.0Hayward Pro-Grid manual
Pentair FNS Plus FNSP36363.61.007.2Pentair FNS Plus guide (2025)
Pentair FNS Plus FNSP48484.81.009.6Pentair FNS Plus guide (2025)
Pentair FNS Plus FNSP60606.01.0012.0Pentair FNS Plus guide (2025)
Pentair Quad DE 60606.01.0012.0Pentair Quad DE guide
Pentair Quad DE 80808.01.0016.0Pentair Quad DE guide
Pentair Quad DE 10010010.01.0020.0Pentair Quad DE guide

Sources: Hayward Pro-Grid manual (ISDE2423EF Rev E); Pentair FNS Plus guide (2025); Pentair Quad DE guide; per-10-sq-ft and can counts are PC&S arithmetic. Download CSV

DE charge after a cleaning, by filter model (pounds, maker manuals, 2026)Pentair uses 1.0 lb per 10 sq ft of grid area; Hayward Pro-Grid uses 1.25 lb
DE charge after a cleaning, by filter model (pounds, maker manuals, 2026)Bar chart of DE charge: Hayward Pro-Grid DE2420 3.0 lb, DE3620 4.5, DE4820 6.0, DE6020 7.5, DE7220 9.0; Pentair FNS Plus 36, 48 and 60 take 3.6, 4.8 and 6.0 lb; Pentair Quad DE 60, 80 and 100 take 6, 8 and 10 lb.Hayward Pro-Grid DE2420: 3Hayward Pro-Grid DE24203Hayward Pro-Grid DE3620: 4.5Hayward Pro-Grid DE36204.5Hayward Pro-Grid DE4820: 6Hayward Pro-Grid DE48206Hayward Pro-Grid DE6020: 7.5Hayward Pro-Grid DE60207.5Hayward Pro-Grid DE7220: 9Hayward Pro-Grid DE72209Pentair FNS Plus FNSP36: 3.6Pentair FNS Plus FNSP363.6Pentair FNS Plus FNSP48: 4.8Pentair FNS Plus FNSP484.8Pentair FNS Plus FNSP60: 6Pentair FNS Plus FNSP606Pentair Quad DE 60: 6Pentair Quad DE 606Pentair Quad DE 80: 8Pentair Quad DE 808Pentair Quad DE 100: 10Pentair Quad DE 10010

Use the amount printed on your own filter label when it differs.

Source: Source: Hayward Pro-Grid manual (ISDE2423EF Rev E); Pentair FNS Plus guide (2025) and Quad DE guide. Accessed October 2026.. Download chart data (CSV)

Pentair’s Quad DE guide notes that a level 1-lb coffee can holds roughly half a pound of DE, so a 48 sq ft filter needs about 9.6 cans at Pentair’s rate and 12 at Hayward’s. Pentair tells owners to wear a NIOSH approved dust mask and safety glasses when handling DE, and the EPA WaterSense pool guide lists DE as harmful if inhaled. Spent DE stays out of storm drains: the City of Meadows Place, Texas, sends it to the garbage and bars it from septic systems (Meadows Place, 2022).

How do you clean a sand filter?

You backwash it: reversed flow lifts the bed and flushes trapped dirt out the waste line, about 2 minutes on a Hayward ProSeries and 3 to 5 minutes on a Pentair Triton. When pressure is still 4 to 6 psi over the clean reading right after a backwash, Pentair calls for a chemical clean of the sand bed instead of more backwashing.

Pentair’s chemical cleaning sequence for its Sand Dollar and Triton filters: backwash, drain the tank, set the valve to BACKWASH, pour a label-mixed filter cleaner into the pump strainer with the pump running, then switch off and let it stand overnight (12 hours in the Sand Dollar guide) before backwashing again. Natural Chemistry’s Filter Perfect label for sand filters calls for at least 6 hours with the valve on FILTER or closed.

Hayward’s ProSeries manual adds one manual fix: if the sand surface crusts or cakes, remove about 1 inch of sand. The full procedure, the water each backwash sends down the drain and the sand weights for a media change are in our how to backwash a pool filter guide.

Filter-by-filter cleaning procedure, chemical step and replacement rule, from each maker's documents
Filter (type)Routine cleaningChemical stepRefresh or replaceSource
Pentair Clean & Clear Plus (cartridge)Hose at a 45 degree angle, top to bottom, between pleats; at least 30 minutes start to finishSoak at least 1 hour in filter cleaner, 1 cup TSP or 1 cup dishwasher detergent per 5 gallons; acid 1:20 only after degreasingReplace when pressure stays high after manual cleaning and an acid soakPentair cleaning guide; Pentair install guide (2025); Pentair education center
Hayward SwimClear (cartridge)Wash inside and outside with a garden hose, then brush the pleats; no pressure washerNot specified in the manualReplace when the cleaned start pressure is more than 6 psi above newHayward SwimClear manual
Hayward Pro-Grid (DE grids)Backwash about 2 minutes; for a teardown, hose the element cluster and brush; no pressure washerNot specified in the manualInspect the grid cloth for tears at each cleaningHayward Pro-Grid manual; Hayward filter-types article (2023)
Pentair FNS Plus (DE grids)Backwash until the discharge runs clear; hand clean when pressure stays high after backwashing or at winterizingNot specified in the manualGrid lifetime 2 to 3 years in EPA WaterSense table; 6 months to 15 years per UnicelPentair FNS Plus guide; EPA WaterSense (2022); Unicel
Hayward ProSeries (sand)Backwash about 2 minutes, rinse 1/2 to 1 minuteRemove 1 inch of crusted sand if the surface cakesFirst sand change after roughly 5 yearsHayward ProSeries manual; Hayward filter-types article (2023)
Pentair Sand Dollar and Triton (sand)Backwash about 3 minutes (Sand Dollar) or 3 to 5 minutes (Triton), rinse about 30 secondsChemical clean overnight (12 hours) when pressure is still 4 to 6 psi over start after a backwashSand media lifetime 3 to 6 years in EPA WaterSense tablePentair sand filter guide; Pentair Triton guide; EPA WaterSense (2022)

Sources: Pentair cleaning guide; Pentair install guide (2025); Pentair education center; Hayward SwimClear; Hayward Pro-Grid; Hayward filter-types article; Pentair FNS Plus; EPA WaterSense (2022); Unicel; Hayward ProSeries; Pentair Sand Dollar; Pentair Triton. Download CSV

Should you clean or replace the cartridge?

Replace when cleaning stops restoring the start pressure. Hayward’s rule: a cleaned SwimClear set that restarts more than 6 psi above its new-cartridge reading gets replaced. Unicel adds shorter cycles between cleanings, low flow with high pressure, and torn media or a collapsed core. EPA’s WaterSense guide puts typical cartridge life at 2 to 4 years. If the whole filter is due for replacement, our pool filter types comparison sets cartridge, sand and DE filters side by side on water use, media prices and 10-year cost.

Decision table: hose, degrease, acid soak, sanitize or replace
If your situation isDo thisSource
Cartridge gauge reads about 10 psi over the clean start (7 to 10 psi on a SwimClear)Open the filter and hose each cartridge top to bottom; record the new starting pressurePentair; Hayward
Cartridge feels slick, or the pool sees heavy sunscreen and swimmer useDegrease: soak at least 1 hour (overnight is better) in label cleaner, TSP or dishwasher detergent, then rinsePentair; MAHC 2024; Unicel
White or gray crust remains, and an acid drop on the degreased media fizzesAcid soak at 1 part muriatic acid to 20 parts water, 10 minutes per halfUnicel; Pentair
The pool just had an algae bloom or a fecal incidentDegrease, then soak 1 hour in 1 quart household bleach per 5 gallons and rinseMAHC 2024 5.7.2.4.3.3.7
The pool runs a biguanide sanitizer (Baquacil, SoftSwim)Use the biguanide maker's filter cleaner first; skip TSP and Strip KwikUnicel; BioGuard product sheet
A cleaned cartridge restarts more than 6 psi above its new-cartridge readingReplace the cartridge setHayward SwimClear manual
Torn media, collapsed core or cracked end capReplace the cartridge; cleaning will not fix itUnicel
DE filter pressure stays high right after a backwashOpen the tank, hose the grids at a 45 degree angle, recoat with the label amount of DEPentair FNS Plus guide
Sand filter at 8 to 10 psi over cleanBackwash; a sand bed is cleaned in place, not taken apartHayward ProSeries manual

Sources: Pentair; Hayward SwimClear; CDC MAHC 2024; Unicel; BioGuard Strip Kwik sheet; Pentair FNS Plus; Hayward ProSeries. Download CSV

Cartridge decision path: hose at about 10 psi over start, degrease oily media, acid soak only when a drop test fizzes, sanitize after algae, replace at more than 6 psi over new (Pentair, Hayward, Unicel, MAHC 2024; compiled October 2026).
Cartridge decision path: hose at about 10 psi over start, degrease oily media, acid soak only when a drop test fizzes, sanitize after algae, replace at more than 6 psi over new (Pentair, Hayward, Unicel, MAHC 2024; compiled October 2026).
Published replacement rules and intervals for cartridges, DE grids and sand
Filter mediaPublished replacement rule or intervalPublisherType of source
CartridgeReplace when the cleaned start pressure is more than 6 psi above the new-cartridge startHayward (SwimClear manual)Filter maker manual
CartridgeNo defined end point: shorter cycles between cleanings, low flow with high differential pressure, or a tear or collapsed coreUnicelCartridge maker FAQ
CartridgeMedia lifetime 2 to 4 yearsU.S. EPA WaterSense (Sept 2022)Federal guide citing a 2010 study
Cartridge (public pools)Keep one full spare set on site, clean and dryCDC MAHC 2024 5.7.2.4.4Model code
DE gridsGrid lifetime 2 to 3 yearsU.S. EPA WaterSense (Sept 2022)Federal guide
DE gridsAnywhere from 6 months to 15 years, depending on maintenance, water temperature and chemistryUnicelGrid maker FAQ
SandRoughly 5 years before the first sand changeHayward (filter-types article, May 2023)Filter maker article
SandMedia lifetime 3 to 6 yearsU.S. EPA WaterSense (Sept 2022)Federal guide

Sources: Hayward SwimClear manual; Unicel; EPA WaterSense (Sept 2022); CDC MAHC 2024; Hayward (May 2023). Download CSV

A professional filter cleaning is usually billed outside weekly service: from $145 at Pearlin Pools in Brevard County, Florida, and $80 or $100 at two Arizona companies quoted by Thumbtack in August 2026. Our pool service cost survey has the other line items. A whole new filter costs far more: our pool equipment price index puts the 2026 median at $1,819 for a 325 to 525 sq ft inground cartridge filter and $1,539 for a 48 to 60 sq ft DE filter.

When should you call a pro? When the clean start pressure keeps creeping up after a full degrease and acid cycle, when the lid leaks at the clamp after reassembly, or when the gauge does not return to 0 psi with the pump off, which Pentair lists as a reason to replace the gauge. Ask the company whether its price includes a degreasing soak and a new start-pressure reading; our pool cleaning service guide covers what weekly plans include.

How we compiled this

In October 2026 we read 10 filter and cartridge maker documents (Pentair Clean & Clear Plus cleaning and install guides, FNS Plus, Quad DE, Sand Dollar and Triton guides; Hayward SwimClear, Pro-Grid and ProSeries manuals; the Unicel FAQ), 3 cleaner labels, CDC’s 2024 Model Aquatic Health Code, the EPA WaterSense pool guide and 3 local government pages. Prices come from our service survey and equipment index. We did not test cleaners or filters; products appear only because their documents state the numbers.

Frequently Asked Questions

What's the best way to clean your pool filter?

Follow the gauge and the maker’s method for your filter type. Cartridges: hose top to bottom at a 45 degree angle at about 10 psi over the clean start, and degrease oily ones for at least 1 hour (Pentair). Sand: backwash 2 to 5 minutes. DE: backwash, then recoat with 1.0 to 1.25 lb of DE per 10 sq ft of grid area (Pentair; Hayward).

Can I use Dawn to clean my pool filter cartridge?

Hand dish soap is not on any maker list we found. Pentair and the 2024 Model Aquatic Health Code list 1 cup of automatic dishwasher detergent per 5 gallons, alongside TSP and labeled filter cleaners (MAHC 2024). Whatever you use, rinse until no suds remain: Pentair warns that cleaner left in the media before an acid soak permanently restricts flow.

How many times should a pool filter be cleaned?

As often as the gauge says, not a set number. Pentair cleans at about 10 psi over the starting pressure, Hayward at 7 to 10 psi for cartridges and 8 to 10 psi for DE and sand. Unicel notes that cleaning a cartridge too often lowers filtration, because the light dirt layer it holds helps trap fine particles.

Can I use vinegar to clean pool filters?

None of the filter manuals, cartridge makers or the CDC code we read lists vinegar. For mineral scale, Pentair specifies 1 part muriatic acid to 20 parts water for 10 minutes per half, after degreasing. Unicel suggests a drop test first: if a few drops of acid on the clean media do not bubble, the cartridge does not need acid at all.

Are cartridge filters washable?

Yes, with a garden hose, not a pressure washer. Pentair says to hold a straight-flow nozzle at a 45 degree angle and wash top to bottom between the pleats; Hayward adds gentle brushing and warns that pressure washing can damage the element. Fort Worth Water puts a hose-off at 20 to 30 gallons of water.

How long does it take to clean a pool filter?

Pentair puts a Clean & Clear Plus cleaning at least 30 minutes to open, hose, reassemble and restart. Soaks add time: at least 1 hour for TSP or dishwasher detergent, 6 hours or overnight for Natural Chemistry Filter Perfect, and two 10-minute acid baths if scale needs them. Unicel suggests alternating two cartridge sets so one can soak. Spa cartridges follow their own makers’ intervals, from 3 months to 3 years, as our guide on how to clean a hot tub filter shows.

Can I make homemade pool cartridge filter cleaner?

Yes. Filter makers print two home recipes: 1 cup of trisodium phosphate or 1 cup of automatic dishwasher detergent per 5 gallons of water, soaked at least 1 hour (Pentair) or overnight (MAHC 2024). Skip TSP in a biguanide pool, where Unicel says it can bond with the sanitizer film into a gum that ruins the cartridge.

Sources

  1. Pentair. Clean and Clear Plus Cartridge Filter: Cartridge Cleaning Guide. Accessed 2026-10-26.
  2. Pentair. Clean and Clear Plus Cartridge Filter Installation and User Guide (2025). Accessed 2026-10-26.
  3. Pentair. Cleaning and Maintaining Your Pool Filters. Accessed 2026-10-26.
  4. Pentair. FNS Plus Vertical Grid D.E. Filter Installation and User Guide (2025). Accessed 2026-10-26.
  5. Pentair. Quad D.E. Cartridge Style D.E. Filter Installation and User Guide. Accessed 2026-10-26.
  6. Pentair. Sand Dollar and Cristal-Flo II Top Mount Sand Filter Installation and User Guide. Accessed 2026-10-26.
  7. Pentair. Triton Side Mount Sand Filter Installation and User Guide. Accessed 2026-10-26.
  8. Hayward. SwimClear Cartridge Filter Owner Manual (ISC2031EF Rev B). Accessed 2026-10-26.
  9. Hayward. Pro-Grid Vertical DE Filter Owner Manual (ISDE2423EF Rev E). Accessed 2026-10-26.
  10. Hayward. ProSeries High Rate Sand Filters Owner Manual (IS210TS Rev A). Accessed 2026-10-26.
  11. Hayward. What are the Differences Between Filter Types? (May 22, 2023). Accessed 2026-10-26.
  12. Unicel. Maintenance and FAQ. Accessed 2026-10-26.
  13. CDC. Model Aquatic Health Code, 5th Edition (2024), section 5.7.2. Accessed 2026-10-26.
  14. Natural Chemistry. Filter Perfect directions for use. Accessed 2026-10-26.
  15. BioGuard. Strip Kwik product sheet (hosted by Ace Swim). Accessed 2026-10-26.
  16. Simple Green. How to Clean a Cartridge Pool Filter. Accessed 2026-10-26.
  17. U.S. EPA. WaterSense: Making a Splash, Pool Water Efficiency (2022). Accessed 2026-10-26.
  18. City of Fort Worth. Pools (Save Fort Worth Water). Accessed 2026-10-26.
  19. County of San Diego. Pool, Spa, and Fountain Pollution Prevention Practices (June 5, 2026). Accessed 2026-10-26.
  20. City of Meadows Place, Texas. Only Rain Down the Storm Drain: Not Diatomaceous Earth (2022). Accessed 2026-10-26.
  21. CDC. Microbes in Pool Filter Backwash, Metro-Atlanta, 2012 (MMWR 2013;62(19)). Accessed 2026-10-08.
  22. Pearlin Pools. Pool Service Cost in Brevard County FL. Accessed 2026-10-08.
  23. Thumbtack. 2026 Pool Cleaning Costs (archived August 14, 2026). Accessed 2026-10-08.
  24. PC&S. Pool Equipment Prices 2026 (PC&S research). Accessed 2026-10-26.
  25. Atomic Filters. How to Clean Pool Filter Cartridge Guide (claim checked). Accessed 2026-10-26.
  26. Royal Swimming Pools. How to Backwash a Pool Filter (claim checked). Accessed 2026-10-26.
Free for homeowners

Get Quotes From Licensed Local Pool Pros

Tell us what you need and your ZIP code. We match you with pool companies that cover your area.