
Pool Light Not Working? Troubleshoot From Breaker and GFCI to Bulb and Niche, Safely
Pool light not working? Check the switch, timer and breaker, reset a tripped GFCI once, then resync color lights and check the water level; a GFCI that trips again means a fault for a licensed electrician.
- ✓Power off before hands onBulb and gasket work happens on the deck with the breaker off (2024 IRC E4206.5.1).
- ✓A tripping GFCI is a warningIt cuts power at as little as 0.006 A of leakage (CPSC).
- ✓Out of sync is not brokenHayward resyncs with an 11 to 13 second off period.
Key takeaways
- Start with power you can see: switch, timer, automation schedule, breaker and GFCI. Pentair’s only troubleshooting line for a dark IntelliBrite 5g is to check the ground fault wiring and reset if necessary (Pentair guide, P/N 619827 Rev C).
- A GFCI cuts power when as little as 0.006 A leaks to ground, and CPSC says to test every GFCI at least once a month and after a power failure (CPSC fact sheet). One that trips again after a reset is reporting a fault.
- Under NEC 680.23(A)(3), mirrored in 2024 IRC E4206.4, any underwater light above the 15 V low-voltage contact limit must be on a GFCI to protect people relamping or servicing it. Never bypass it.
- Hayward color lights that fall out of step resync with a timed 11 to 13 second off period, and flashing or dim lights get a 2 minute power-down, per Hayward TSG-UCL100e.
- CPSC lists underwater lights that flicker, or are on when they should be off, among the warning signs of current in the water and knows of 33 pool and spa electrocution deaths since 2002 (CPSC).
Why is my pool light not working?
Eight faults cover nearly every dead or misbehaving pool light: no power from the switch, timer or breaker; a tripped GFCI; a failed 12 V transformer; thermal shutdown from low water; color lights out of sync; flicker from voltage drop; water inside the lens; and a burned-out incandescent lamp. The symptom table maps each one to a safe first check and the right person to fix it.
| Symptom | Most likely cause | Safe first check | Who fixes it | Source |
|---|---|---|---|---|
| Light dark, everything else on the circuit dark too | Tripped breaker or GFCI, or the timer or automation relay is not calling for the light | Check the switch, timer and automation schedule; reset the GFCI once | Owner; electrician if the GFCI trips again | Pentair IntelliBrite 5g guide; Hayward TSG-UCL100e |
| GFCI trips as soon as the light is switched on | Ground fault: water in the fixture or cord, or damaged wiring | Leave it off and keep people out of the water | Licensed electrician or qualified pool pro | CPSC GFCI fact sheet; 2024 IRC E4206.4 (NEC 680.23(A)(3)) |
| Light dark, GFCI and breaker fine, 12 V system | Failed transformer or loose low-voltage junction | Confirm the transformer's switch or relay is on | Pool pro with a meter: 120 V in, 12 to 14 V out | Hayward TSG-UCL100e, pages 18 to 20 |
| Light goes off after a few minutes, then back on | Thermal protection: the fixture is not fully under water | Check the water level against the light | Owner: top up the pool | Pentair IntelliBrite 5g guide (10 minute cool-down) |
| Color lights show different colors | Lights out of sync after a power outage, brownout or rapid toggling | Run the maker's resync sequence | Owner | Hayward TSG-UCL100e, pages 7 and 21 to 23 |
| Flickering or dim | Voltage drop, a poor connection or a failing light; flicker can also signal current in the water | Get swimmers out; power off 2 minutes, then retest | Electrician if it persists | Hayward TSG-UCL100e, pages 24 to 26; CPSC |
| Fog or water droplets inside the lens | Failed lens gasket or cord seal | Switch off at the breaker; do not use the light | Pool pro: new gasket or fixture | Pentair guide (new lens gasket P/N 79101600); 2024 IRC E4206.5 (NEC 680.23(B)(4)) |
| Incandescent light dark, nothing tripped | Burned-out lamp: about 2,000 hours average life for a 500 W R40 pool lamp | Breaker off, then lift the fixture onto the deck | Owner if comfortable; pool pro otherwise | Halco 104042 listing (ePoolSupply, Nov 2026) |
Sources: Pentair IntelliBrite 5g guide (P/N 619827 Rev C); Hayward TSG-UCL100e (2017); CPSC GFCI fact sheet; CPSC Don’t Swim With Shocks; 2024 IRC Chapter 42; ePoolSupply Halco listing. Accessed November 9, 2026. Download CSV
Two causes are easy to miss. Pentair says an IntelliBrite left out of the water and powered on for more than 10 minutes switches itself off for a 10 minute cool-down, so a light near a low waterline can cycle on and off. Hayward says switched color lights fall out of sync after power outages, brownouts, repeated toggling, voltage drop or an overloaded transformer; that looks like a fault but is fixed with a resync.
How do you troubleshoot a pool light, step by step?
Work from the outside in, and stop where the next step needs tools on a live circuit. Check the switch and schedule, then the breaker, then reset the GFCI once, then resync or power-cycle color lights, then check the water level and the lens. Anything inside the junction box, transformer or a 120 V circuit belongs to a licensed electrician or qualified pool pro.

- Clear the water firstIf anyone feels tingling, or the light flickers or is on when it should be off, get everyone out without the metal ladder and cut power at the breaker (CPSC).
- Check the switch, timer and automationConfirm the wall switch is on, the timer is not in its off window, and the automation relay or app is calling for the light (Hayward TSG-UCL100e, page 19).
- Check the breakerA tripped breaker sits in the middle or off position; switch it fully off, then on.
- Reset the GFCI oncePress reset on the GFCI receptacle or breaker that feeds the light. If it trips again with the light on, stop here: leave it off and call an electrician.
- Power-cycle or resync color lightsPentair: off more than 5 seconds restores the last saved show. Hayward: on at least 60 seconds, off 11 to 13 seconds, back on; then off 2 minutes to lock.
- Check the water levelThe top of the lens sits at least 18 in below normal water level (2024 IRC E4206.4.2); a low pool can trigger thermal shutdown on some LEDs.
- Look at the lens from the deckFog, droplets or a dark patch inside means water got past the gasket or cord seal: breaker off, do not use the light.
- Lamp or fixture work, breaker offWith the breaker off and the switch tested dark, a wet-niche light lifts onto the deck without draining; the relamp steps are in our pool lighting guide.
The full relamp and fixture-swap procedure, with Pentair’s 12 manual steps and the 4 ft of coiled cord, is in our pool lighting guide, so this page stops at diagnosis. Lights wired through a controller often fail at the relay or schedule, which our pool automation system guide explains.
Why does my pool light keep tripping the GFCI?
Because current is leaking to ground somewhere on the light circuit, most often water inside the fixture or cord, or damaged wiring in the conduit or junction box. A GFCI trips at as little as 0.006 A of difference between outgoing and returning current, according to CPSC. Reset it once; a second trip means the fault is still there, and it needs an electrician.
The code assumes water can reach the fixture. 2024 IRC E4206.5 (NEC 680.23(B)(4)) requires the cord ends inside a wet-niche light to be potted so water cannot enter through the cord, and E4206.4 puts a GFCI on every light above 15 V precisely to protect the person relamping it. A light that trips its GFCI after years of service usually has a failed lens gasket, which is why Pentair says to always fit a new gasket (P/N 79101600) whenever an IntelliBrite is opened.
Old GFCIs fail too. CPSC says blackouts and power disturbances can damage a GFCI, so test it monthly: press test, the protected device should go dark; press reset, it should come back. If it will not reset with the light disconnected by an electrician, the GFCI itself is bad. Bonding faults, a separate safety system, are covered in our pool bonding guide.
How do I reset my pool light?
By timing the power. Switched color lights reset and resync through the wall switch: Pentair IntelliBrite 5g returns to its last saved show after more than 5 seconds off, and Hayward Universal ColorLogic resyncs with an off period of exactly 11 to 13 seconds, then 2 minutes off to lock it in. A tripped GFCI resets with its button, once.
| Light | How to reset or resync | Source |
|---|---|---|
| Pentair IntelliBrite 5g (switched) | Power is off more than 5 seconds: the light returns to the last saved show or color. Switch off and on 1 to 12 times to pick a show or color; 13 times holds, 14 recalls | Pentair IntelliBrite 5g guide, P/N 619827 Rev C, pages 2 to 5 |
| Hayward Universal ColorLogic and CrystaLogic (switched) | Light on at least 60 seconds; off for 11 to 13 seconds, then straight back on; repeat until all lights match; then off at least 2 minutes | Hayward TSG-UCL100e, page 7 |
| Hayward lights on an OmniLogic | Tap the light on the dashboard, pick the body of water, tap the resync icon | Hayward TSG-UCL100e, page 8 |
| Hayward ColorLogic Light Controller | Lights on, wait 2 minutes, hold the resync button at least 3 seconds | Hayward TSG-UCL100e, page 9 |
| Any light, flashing or dim | Power down at least 2 minutes at the breaker or controller, then retest | Hayward TSG-UCL100e, page 25 |
| GFCI receptacle or breaker | Press reset once. If it trips again, stop and call an electrician | CPSC GFCI fact sheet (Pub. 099) |
Sources: Pentair IntelliBrite 5g guide, P/N 619827 Rev C; Hayward TSG-UCL100e (2017); CPSC Pub. 099. Accessed November 9, 2026. Download CSV

Why is my pool light flickering or dim?
Treat flicker as a safety signal first: CPSC lists flickering underwater lights among the signs of electricity in the water, so get swimmers out. Then the usual causes are voltage drop, a poor connection or a failing light. Hayward’s guide says its LEDs flash when they get too little power and need 12 to 14 V AC at the junction point.
Hayward’s sequence for a flashing or dim switched light is a 2 minute power-down at the breaker or controller, then a retest; if it still flashes, a technician checks for 12 to 14 V at the junction box and 120 V in and 14 V out at the transformer (TSG-UCL100e, pages 24 to 26). Long cords and several lights on one 300 W transformer add voltage drop; Pentair recommends no more than 3 pool lights and 1 spa light on one 300 W transformer and 100 ft of total cable.
Of 35 sampled emergency room cases of pool and spa electrical injury from 2015 to 2025, a pool light was the source in 2, per our pool electrocution statistics; cords, plugs and outlets caused more. Rare is not zero, which is why the flicker check comes before the meter.
What does NEC 680 say when you fix a pool light?
Article 680 of the National Electrical Code, mirrored in Chapter 42 of the 2024 International Residential Code, sets the rules a repair must keep: GFCI on lights above 15 V (680.23(A)(3)), a Class A GFCI (680.5), sealed cord ends (680.23(B)(4)), deck servicing without entering the water (680.23(B)(6)), and a junction box 4 ft from the pool (680.24(A)(2)).
| Rule that matters when a light fails | 2024 IRC | 2023 NEC | What it means for troubleshooting |
|---|---|---|---|
| GFCI on lights above the low-voltage contact limit, to protect people lamping, relamping or servicing | E4206.4 | 680.23(A)(3) | A 120 V light that trips its GFCI is doing its job; find the fault, do not bypass it |
| Low-voltage contact limit: 15 V RMS sinusoidal AC | Chapter 35 definition | 680.2 | 12 V lights on a listed transformer need no GFCI on the light side |
| Class A GFCI where the chapter requires ground-fault protection | E4206.2 | 680.5(A) and (B) | Replace a failed GFCI with a listed Class A device |
| Cord ends potted inside the fixture to keep water out | E4206.5 | 680.23(B)(4) | Water in the lens or cord means the seal failed; the fixture needs service |
| Wet-niche light lifts out to the deck without anyone entering the water | E4206.5.1 | 680.23(B)(6) | Bulb and gasket work happens on the deck with the breaker off |
| Junction box 4 ft from the inside wall, 4 in above deck or 8 in above max water level | E4206.9.1 | 680.24(A)(2) | The box you may see on the deck; opening it is electrician work |
| Strain relief where the light cord ends in the box | E4206.9.5 | 680.24(E) | A cord pulled loose at the box can cut power to the light |
| Supply circuit no more than 150 V between conductors | E4206.4.1 | 680.23(A)(4) | Pool lights run on 120 V or 12 V systems |
Sources: 2024 IRC Chapter 42 (bracketed 2023 NEC sections), via UpCodes; 2024 IRC Chapter 35 definitions. Accessed November 8 and 9, 2026. Download CSV
Older pools are not forced to upgrade until work is done: CPSC notes the NEC typically applies to new construction or major renovations, and its GFCI rule for underwater pool lighting dates to 1968. A new light circuit or fixture swap may need a permit; unincorporated Miami-Dade charges $148.68 for a residential pool electrical permit that covers lights, and our pool permits guide explains when one applies. Spa lights and the GFCI rules for hot tubs, 680.43 and 680.44, are covered in our hot tub wiring guide.
How much does it cost to fix a pool light, and how long do they last?
A repair runs $65 to $150 per light and a full replacement $500 to $1,700 with fixture and labor, according to Angi (July 2026) and HomeGuide (2025). A 500 W incandescent R40 pool lamp averages 2,000 hours, about 1.4 years at 4 hours a night, and costs $24.69 (ePoolSupply, November 2026). Hayward says its LEDs last 10 times longer.

| Item | Cost | Source and date |
|---|---|---|
| Repair per light (diagnose, reseal, reconnect) | $65 to $150 | Angi, updated July 9, 2026 |
| Pool repair labor | $45 to $65 per hour | Angi, 2026 |
| 500 W incandescent R40 lamp, Halco 104042 | $24.69 | ePoolSupply, November 9, 2026 |
| Bulbs alone | $20 to $100 | Angi, 2026 |
| LED fixture alone (12 models listed) | $374.95 to $1,469.00 | ePoolSupply and Inyo Pools, November 1, 2026 |
| Replace a light, fixture and labor | $500 to $1,700 | HomeGuide, 2025 |
| Electrical permit, residential pool or spa incl. lights (unincorporated Miami-Dade) | $148.68 | Miami-Dade Implementing Order 4-63 |
Sources: Angi (Wayback, July 2026); HomeGuide 2025; ePoolSupply, Nov 9, 2026; ePoolSupply fixture listings, Nov 1, 2026; Miami-Dade IO 4-63. Download CSV
Source: Angi (updated July 9, 2026); ePoolSupply and Inyo Pools listings (Nov 1, 2026); HomeGuide (2025).. Download chart data (CSV)
| Question | Input or formula | Result |
|---|---|---|
| How long does a 500 W lamp last at 4 hours a night? | 2,000 hours average life / 4 hours per night | 500 nights, about 1.4 years |
| At 1 hour a night? | 2,000 / 1 | 2,000 nights, about 5.5 years |
| Lamp vs new LED fixture | $24.69 lamp vs $824.95 Pentair IntelliBrite 5g Color, 50 ft (ePoolSupply) | The lamp costs about 3% of the fixture |
| Repair vs replace | $65 to $150 repair (Angi) vs $500 to $1,700 replacement (HomeGuide) | Repair first unless the fixture or niche is damaged |
| Hayward LED warranty window | 3 years parts, 1 year labor (CrystaLogic 320 page) | Check the receipt before paying for a repair |
Sources: Halco 104042 listing; ePoolSupply; Angi; HomeGuide; Hayward CrystaLogic 320 page. PC&S arithmetic, November 2026. Download CSV
Fixture specs, LED running costs and the 6.6 year payback of swapping a 500 W lamp for a 26 W LED are worked out in our pool lighting guide. Other jobs often bundled with a light repair are priced in our pool repair guide.
Which pool light fixes are DIY, and when do you call an electrician?
DIY stops at switches, schedules, a single GFCI reset, resync sequences, the water level and looking at the lens. Call a licensed electrician when a GFCI trips again, anyone feels tingling, the lens holds water, a 12 V system shows no output, the cord will not pull, or the junction box is corroded. A bulb swap with the breaker off is DIY only if you are comfortable doing it.
| Number | What it means | Source |
|---|---|---|
| 0.006 A | Leakage current at which a GFCI cuts power | CPSC GFCI fact sheet |
| Once a month | How often to test every GFCI, plus after a power failure | CPSC GFCI fact sheet |
| 15 V | Low-voltage contact limit (AC RMS); above it, an underwater light needs a GFCI | 2024 IRC Ch. 35; NEC 680.2, 680.23(A)(3) |
| 11 to 13 seconds | Timed off period to resync Hayward switched color lights | Hayward TSG-UCL100e |
| 10 minutes | Pentair IntelliBrite cool-down if run out of water more than 10 minutes | Pentair guide |
| 12 to 14 V AC | Voltage a Hayward low-voltage light needs at the junction point | Hayward TSG-UCL100e |
| 2,000 hours | Average life of a 500 W R40 pool lamp | Halco 104042 listing, Nov 2026 |
| 33 | Pool and spa electrocution deaths known to CPSC since 2002 | CPSC |
Sources: CPSC GFCI fact sheet; 2024 IRC Ch. 35; Hayward TSG-UCL100e; Pentair guide; ePoolSupply; CPSC. Download CSV
| If your situation is | Do this | Why (source) |
|---|---|---|
| Anyone feels tingling, or the light flickers or is on when it should be off | Get everyone out without the metal ladder, cut power at the breaker, call an electrician | CPSC lists these as warning signs of current in the water |
| Light dark, switch or timer off | Turn it on or fix the schedule; check the automation relay is calling for the light | Hayward: make sure the lights are being called for |
| GFCI tripped once | Reset it once and test the light | CPSC: test and reset procedure |
| GFCI trips again | Leave it off and book a licensed electrician; do not swap in a non-GFCI device | 2024 IRC E4206.4 (NEC 680.23(A)(3)) requires the GFCI |
| Color lights out of step | Run the maker's resync: Hayward 11 to 13 s off; Pentair off more than 5 s | Hayward TSG-UCL100e; Pentair guide |
| Light cycles off and on, water low | Top up above the light | Pentair 10 minute thermal cool-down |
| Fog or water in the lens | Breaker off; new gasket or fixture by a pro | Pentair: always fit a new lens gasket when opened |
| Incandescent dark, nothing tripped | Breaker off, lift fixture to the deck, replace the lamp and gasket, or hire a pool pro | 2024 IRC E4206.5.1; Pentair relamp steps |
| 12 V light dark, GFCI fine | Pool pro checks 120 V in and 12 to 14 V out at the transformer | Hayward TSG-UCL100e |
| Cord will not pull, niche cracked or junction box corroded | Licensed electrician; ask whether a permit is needed | Miami-Dade charges $148.68 for a pool electrical permit |
Sources: Pentair IntelliBrite 5g guide (P/N 619827 Rev C); Hayward TSG-UCL100e (2017); CPSC GFCI fact sheet; CPSC Don’t Swim With Shocks; 2024 IRC Chapter 42; ePoolSupply Halco listing. Accessed November 9, 2026. Download CSV
How we compiled this
In November 2026 we read Pentair’s IntelliBrite 5g guide (P/N 619827 Rev C), Hayward’s 43-page Universal ColorLogic troubleshooting guide (TSG-UCL100e), Chapter 42 of the 2024 IRC with its bracketed 2023 NEC sections, CPSC’s GFCI fact sheet and pool shock page, a retailer lamp listing and the six readable top-ranking pages: 8 primary documents, plus cost figures reused from our pool lighting guide. We did not test any light; forum posts were read for question wording only.
Frequently Asked Questions
How do I reset my pool light?
Time the power off. A Pentair IntelliBrite 5g returns to its last saved show after more than 5 seconds off. A Hayward switched color light resyncs when you leave it on 60 seconds, switch it off for 11 to 13 seconds and straight back on, then off for 2 minutes. If a GFCI tripped, press reset once; a second trip needs an electrician.
What causes pool lights to stop working?
Usually power, not the light: a switch, timer or automation schedule, a tripped breaker, or a GFCI that tripped on a ground fault such as water in the fixture. Then come color lights out of sync, a failed 12 V transformer, thermal shutdown from low water and burned-out lamps; a 500 W R40 pool lamp averages 2,000 hours (Halco listing, 2026).
How much does a pool light cost to fix?
$65 to $150 per light for a repair such as resealing or reconnecting, according to Angi (updated July 2026), and $500 to $1,700 per light to replace the fixture with labor, according to HomeGuide (2025). A 500 W incandescent lamp alone was $24.69 at ePoolSupply in November 2026, and LED fixtures listed at $374.95 to $1,469.00.
What is the average lifespan of a pool light?
A 500 W incandescent R40 pool lamp averages 2,000 hours, per the Halco 104042 listing (2026): about 1.4 years at 4 hours a night or 5.5 years at 1 hour. Hayward says its CrystaLogic LEDs last 10 times longer than incandescent bulbs, and covers them for 3 years on parts and 1 year on labor.
Why does my pool light keep tripping the GFCI?
A ground fault: current leaking to ground, often through water inside the fixture or cord, or damaged wiring. A GFCI trips at as little as 0.006 A (CPSC), and NEC 680.23(A)(3) requires one on any underwater light above 15 V. Reset it once; if it trips again, leave it off and call a licensed electrician.
Is a flickering pool light dangerous?
It can be. CPSC lists underwater lights that flicker, or are on when they should be off, among the warning signs of electricity in the water. Get everyone out without using a metal ladder and cut power at the breaker. Once the pool is clear, Hayward’s guide traces most flicker to voltage drop, poor connections or a failing light.
Sources
- International Code Council via UpCodes. 2024 International Residential Code, Chapter 42 Swimming Pools (bracketed 2023 NEC sections). Accessed 2026-11-08.
- International Code Council via UpCodes. 2024 International Residential Code, Chapter 35 definitions (low-voltage contact limit). Accessed 2026-11-01.
- Pentair. IntelliBrite 5g Pool LED Light Installation and User's Guide, P/N 619827 Rev C. Accessed 2026-11-09.
- Hayward. Universal ColorLogic & CrystaLogic Troubleshooting Guide Residential, TSG-UCL100e (2017). Accessed 2026-11-09.
- CPSC. GFCI Fact Sheet, Pub. 099. Accessed 2026-11-09.
- CPSC. Don't Swim With Shocks: Electrical Safety In and Around Pools, Spas and Hot Tubs. Accessed 2026-11-09.
- ePoolSupply. Halco 104042 Incandescent R40 Lamp 500 W listing. Accessed 2026-11-09.
- Hayward. CrystaLogic 320 product page. Accessed 2026-11-01.
- Angi. How Much Do Swimming Pool Repairs Cost? (updated July 9, 2026), Wayback copy. Accessed 2026-10-08.
- HomeGuide. How Much Does It Cost to Repair a Pool? (2025). Accessed 2026-10-08.
- ePoolSupply. Pool light listings. Accessed 2026-11-01.
- Miami-Dade County. Implementing Order 4-63, fee schedule. Accessed 2026-10-07.
Related pages
Get Quotes From Licensed Local Pool Pros
Tell us what you need and your ZIP code. We match you with pool companies that cover your area.